[PATCH 10/11] ARM: mmp: remove device definitions
Arnd Bergmann
arnd at kernel.org
Fri Oct 21 08:49:40 PDT 2022
From: Arnd Bergmann <arnd at arndb.de>
Since all board support is now gone, a lot of code in the
platform is no longer called and can be removed as well.
The remaining parts are:
* The interrupt numbers for pxa910 are still needed for the
power management support.
* The 'mfp' device is still statically initialized from
platform code, though this could be moved into the
pinctrl code
* The CPU identification code is used for the cpu_is_mmp*()
macros.
Signed-off-by: Arnd Bergmann <arnd at arndb.de>
---
arch/arm/mach-mmp/Makefile | 2 +-
arch/arm/mach-mmp/common.c | 5 -
arch/arm/mach-mmp/common.h | 2 -
arch/arm/mach-mmp/devices.c | 359 --------------------------------
arch/arm/mach-mmp/devices.h | 57 -----
arch/arm/mach-mmp/irqs.h | 173 ---------------
arch/arm/mach-mmp/mfp.h | 35 ----
arch/arm/mach-mmp/mmp2.c | 71 +------
arch/arm/mach-mmp/mmp2.h | 83 --------
arch/arm/mach-mmp/pm-mmp2.c | 34 ---
arch/arm/mach-mmp/pm-mmp2.h | 2 +-
arch/arm/mach-mmp/pm-pxa910.c | 106 ----------
arch/arm/mach-mmp/pxa168.c | 126 +----------
arch/arm/mach-mmp/pxa168.h | 123 -----------
arch/arm/mach-mmp/pxa910.c | 99 +--------
arch/arm/mach-mmp/pxa910.h | 79 -------
arch/arm/mach-mmp/regs-apbc.h | 19 --
arch/arm/mach-mmp/regs-apmu.h | 28 ---
arch/arm/mach-mmp/regs-timers.h | 5 -
arch/arm/mach-mmp/regs-usb.h | 155 --------------
arch/arm/mach-mmp/time.c | 9 +-
21 files changed, 7 insertions(+), 1565 deletions(-)
delete mode 100644 arch/arm/mach-mmp/devices.c
delete mode 100644 arch/arm/mach-mmp/devices.h
delete mode 100644 arch/arm/mach-mmp/mfp.h
delete mode 100644 arch/arm/mach-mmp/regs-apbc.h
delete mode 100644 arch/arm/mach-mmp/regs-apmu.h
delete mode 100644 arch/arm/mach-mmp/regs-usb.h
diff --git a/arch/arm/mach-mmp/Makefile b/arch/arm/mach-mmp/Makefile
index cd874c5a6cb8..95d4217132eb 100644
--- a/arch/arm/mach-mmp/Makefile
+++ b/arch/arm/mach-mmp/Makefile
@@ -2,7 +2,7 @@
#
# Makefile for Marvell's PXA168 processors line
#
-obj-y += common.o devices.o time.o
+obj-y += common.o time.o
# SoC support
obj-$(CONFIG_CPU_PXA168) += pxa168.o
diff --git a/arch/arm/mach-mmp/common.c b/arch/arm/mach-mmp/common.c
index e94349d4726c..b3c1a248db31 100644
--- a/arch/arm/mach-mmp/common.c
+++ b/arch/arm/mach-mmp/common.c
@@ -58,8 +58,3 @@ void __init mmp2_map_io(void)
mmp_map_io();
iotable_init(mmp2_io_desc, ARRAY_SIZE(mmp2_io_desc));
}
-
-void mmp_restart(enum reboot_mode mode, const char *cmd)
-{
- soft_restart(0);
-}
diff --git a/arch/arm/mach-mmp/common.h b/arch/arm/mach-mmp/common.h
index ed56b3f15b45..e18f05d5d68d 100644
--- a/arch/arm/mach-mmp/common.h
+++ b/arch/arm/mach-mmp/common.h
@@ -1,9 +1,7 @@
/* SPDX-License-Identifier: GPL-2.0 */
#include <linux/reboot.h>
-#define ARRAY_AND_SIZE(x) (x), ARRAY_SIZE(x)
extern void mmp_timer_init(int irq, unsigned long rate);
extern void __init mmp_map_io(void);
extern void __init mmp2_map_io(void);
-extern void mmp_restart(enum reboot_mode, const char *);
diff --git a/arch/arm/mach-mmp/devices.c b/arch/arm/mach-mmp/devices.c
deleted file mode 100644
index 9968239d8041..000000000000
--- a/arch/arm/mach-mmp/devices.c
+++ /dev/null
@@ -1,359 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-mmp/devices.c
- */
-
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/dma-mapping.h>
-#include <linux/delay.h>
-
-#include <asm/irq.h>
-#include "irqs.h"
-#include "devices.h"
-#include <linux/soc/mmp/cputype.h>
-#include "regs-usb.h"
-
-int __init mmp_register_device(struct mmp_device_desc *desc,
- void *data, size_t size)
-{
- struct platform_device *pdev;
- struct resource res[2 + MAX_RESOURCE_DMA];
- int i, ret = 0, nres = 0;
-
- pdev = platform_device_alloc(desc->drv_name, desc->id);
- if (pdev == NULL)
- return -ENOMEM;
-
- pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
-
- memset(res, 0, sizeof(res));
-
- if (desc->start != -1ul && desc->size > 0) {
- res[nres].start = desc->start;
- res[nres].end = desc->start + desc->size - 1;
- res[nres].flags = IORESOURCE_MEM;
- nres++;
- }
-
- if (desc->irq != NO_IRQ) {
- res[nres].start = desc->irq;
- res[nres].end = desc->irq;
- res[nres].flags = IORESOURCE_IRQ;
- nres++;
- }
-
- for (i = 0; i < MAX_RESOURCE_DMA; i++, nres++) {
- if (desc->dma[i] == 0)
- break;
-
- res[nres].start = desc->dma[i];
- res[nres].end = desc->dma[i];
- res[nres].flags = IORESOURCE_DMA;
- }
-
- ret = platform_device_add_resources(pdev, res, nres);
- if (ret) {
- platform_device_put(pdev);
- return ret;
- }
-
- if (data && size) {
- ret = platform_device_add_data(pdev, data, size);
- if (ret) {
- platform_device_put(pdev);
- return ret;
- }
- }
-
- return platform_device_add(pdev);
-}
-
-#if IS_ENABLED(CONFIG_USB) || IS_ENABLED(CONFIG_USB_GADGET)
-#if IS_ENABLED(CONFIG_USB_MV_UDC) || IS_ENABLED(CONFIG_USB_EHCI_MV)
-#if IS_ENABLED(CONFIG_CPU_PXA910) || IS_ENABLED(CONFIG_CPU_PXA168)
-
-/*****************************************************************************
- * The registers read/write routines
- *****************************************************************************/
-
-static unsigned int u2o_get(void __iomem *base, unsigned int offset)
-{
- return readl_relaxed(base + offset);
-}
-
-static void u2o_set(void __iomem *base, unsigned int offset,
- unsigned int value)
-{
- u32 reg;
-
- reg = readl_relaxed(base + offset);
- reg |= value;
- writel_relaxed(reg, base + offset);
- readl_relaxed(base + offset);
-}
-
-static void u2o_clear(void __iomem *base, unsigned int offset,
- unsigned int value)
-{
- u32 reg;
-
- reg = readl_relaxed(base + offset);
- reg &= ~value;
- writel_relaxed(reg, base + offset);
- readl_relaxed(base + offset);
-}
-
-static void u2o_write(void __iomem *base, unsigned int offset,
- unsigned int value)
-{
- writel_relaxed(value, base + offset);
- readl_relaxed(base + offset);
-}
-
-
-static DEFINE_MUTEX(phy_lock);
-static int phy_init_cnt;
-
-static int usb_phy_init_internal(void __iomem *base)
-{
- int loops;
-
- pr_info("Init usb phy!!!\n");
-
- /* Initialize the USB PHY power */
- if (cpu_is_pxa910()) {
- u2o_set(base, UTMI_CTRL, (1<<UTMI_CTRL_INPKT_DELAY_SOF_SHIFT)
- | (1<<UTMI_CTRL_PU_REF_SHIFT));
- }
-
- u2o_set(base, UTMI_CTRL, 1<<UTMI_CTRL_PLL_PWR_UP_SHIFT);
- u2o_set(base, UTMI_CTRL, 1<<UTMI_CTRL_PWR_UP_SHIFT);
-
- /* UTMI_PLL settings */
- u2o_clear(base, UTMI_PLL, UTMI_PLL_PLLVDD18_MASK
- | UTMI_PLL_PLLVDD12_MASK | UTMI_PLL_PLLCALI12_MASK
- | UTMI_PLL_FBDIV_MASK | UTMI_PLL_REFDIV_MASK
- | UTMI_PLL_ICP_MASK | UTMI_PLL_KVCO_MASK);
-
- u2o_set(base, UTMI_PLL, 0xee<<UTMI_PLL_FBDIV_SHIFT
- | 0xb<<UTMI_PLL_REFDIV_SHIFT | 3<<UTMI_PLL_PLLVDD18_SHIFT
- | 3<<UTMI_PLL_PLLVDD12_SHIFT | 3<<UTMI_PLL_PLLCALI12_SHIFT
- | 1<<UTMI_PLL_ICP_SHIFT | 3<<UTMI_PLL_KVCO_SHIFT);
-
- /* UTMI_TX */
- u2o_clear(base, UTMI_TX, UTMI_TX_REG_EXT_FS_RCAL_EN_MASK
- | UTMI_TX_TXVDD12_MASK | UTMI_TX_CK60_PHSEL_MASK
- | UTMI_TX_IMPCAL_VTH_MASK | UTMI_TX_REG_EXT_FS_RCAL_MASK
- | UTMI_TX_AMP_MASK);
- u2o_set(base, UTMI_TX, 3<<UTMI_TX_TXVDD12_SHIFT
- | 4<<UTMI_TX_CK60_PHSEL_SHIFT | 4<<UTMI_TX_IMPCAL_VTH_SHIFT
- | 8<<UTMI_TX_REG_EXT_FS_RCAL_SHIFT | 3<<UTMI_TX_AMP_SHIFT);
-
- /* UTMI_RX */
- u2o_clear(base, UTMI_RX, UTMI_RX_SQ_THRESH_MASK
- | UTMI_REG_SQ_LENGTH_MASK);
- u2o_set(base, UTMI_RX, 7<<UTMI_RX_SQ_THRESH_SHIFT
- | 2<<UTMI_REG_SQ_LENGTH_SHIFT);
-
- /* UTMI_IVREF */
- if (cpu_is_pxa168())
- /* fixing Microsoft Altair board interface with NEC hub issue -
- * Set UTMI_IVREF from 0x4a3 to 0x4bf */
- u2o_write(base, UTMI_IVREF, 0x4bf);
-
- /* toggle VCOCAL_START bit of UTMI_PLL */
- udelay(200);
- u2o_set(base, UTMI_PLL, VCOCAL_START);
- udelay(40);
- u2o_clear(base, UTMI_PLL, VCOCAL_START);
-
- /* toggle REG_RCAL_START bit of UTMI_TX */
- udelay(400);
- u2o_set(base, UTMI_TX, REG_RCAL_START);
- udelay(40);
- u2o_clear(base, UTMI_TX, REG_RCAL_START);
- udelay(400);
-
- /* Make sure PHY PLL is ready */
- loops = 0;
- while ((u2o_get(base, UTMI_PLL) & PLL_READY) == 0) {
- mdelay(1);
- loops++;
- if (loops > 100) {
- printk(KERN_WARNING "calibrate timeout, UTMI_PLL %x\n",
- u2o_get(base, UTMI_PLL));
- break;
- }
- }
-
- if (cpu_is_pxa168()) {
- u2o_set(base, UTMI_RESERVE, 1 << 5);
- /* Turn on UTMI PHY OTG extension */
- u2o_write(base, UTMI_OTG_ADDON, 1);
- }
-
- return 0;
-}
-
-static int usb_phy_deinit_internal(void __iomem *base)
-{
- pr_info("Deinit usb phy!!!\n");
-
- if (cpu_is_pxa168())
- u2o_clear(base, UTMI_OTG_ADDON, UTMI_OTG_ADDON_OTG_ON);
-
- u2o_clear(base, UTMI_CTRL, UTMI_CTRL_RXBUF_PDWN);
- u2o_clear(base, UTMI_CTRL, UTMI_CTRL_TXBUF_PDWN);
- u2o_clear(base, UTMI_CTRL, UTMI_CTRL_USB_CLK_EN);
- u2o_clear(base, UTMI_CTRL, 1<<UTMI_CTRL_PWR_UP_SHIFT);
- u2o_clear(base, UTMI_CTRL, 1<<UTMI_CTRL_PLL_PWR_UP_SHIFT);
-
- return 0;
-}
-
-int pxa_usb_phy_init(void __iomem *phy_reg)
-{
- mutex_lock(&phy_lock);
- if (phy_init_cnt++ == 0)
- usb_phy_init_internal(phy_reg);
- mutex_unlock(&phy_lock);
- return 0;
-}
-
-void pxa_usb_phy_deinit(void __iomem *phy_reg)
-{
- WARN_ON(phy_init_cnt == 0);
-
- mutex_lock(&phy_lock);
- if (--phy_init_cnt == 0)
- usb_phy_deinit_internal(phy_reg);
- mutex_unlock(&phy_lock);
-}
-#endif
-#endif
-#endif
-
-#if IS_ENABLED(CONFIG_USB_SUPPORT)
-static u64 __maybe_unused usb_dma_mask = ~(u32)0;
-
-#if IS_ENABLED(CONFIG_PHY_PXA_USB)
-static struct resource pxa168_usb_phy_resources[] = {
- [0] = {
- .start = PXA168_U2O_PHYBASE,
- .end = PXA168_U2O_PHYBASE + USB_PHY_RANGE,
- .flags = IORESOURCE_MEM,
- },
-};
-
-struct platform_device pxa168_device_usb_phy = {
- .name = "pxa-usb-phy",
- .id = -1,
- .resource = pxa168_usb_phy_resources,
- .num_resources = ARRAY_SIZE(pxa168_usb_phy_resources),
- .dev = {
- .dma_mask = &usb_dma_mask,
- .coherent_dma_mask = 0xffffffff,
- }
-};
-#endif /* CONFIG_PHY_PXA_USB */
-
-#if IS_ENABLED(CONFIG_USB_MV_UDC)
-static struct resource pxa168_u2o_resources[] = {
- /* regbase */
- [0] = {
- .start = PXA168_U2O_REGBASE + U2x_CAPREGS_OFFSET,
- .end = PXA168_U2O_REGBASE + USB_REG_RANGE,
- .flags = IORESOURCE_MEM,
- .name = "capregs",
- },
- /* phybase */
- [1] = {
- .start = PXA168_U2O_PHYBASE,
- .end = PXA168_U2O_PHYBASE + USB_PHY_RANGE,
- .flags = IORESOURCE_MEM,
- .name = "phyregs",
- },
- [2] = {
- .start = IRQ_PXA168_USB1,
- .end = IRQ_PXA168_USB1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device pxa168_device_u2o = {
- .name = "mv-udc",
- .id = -1,
- .resource = pxa168_u2o_resources,
- .num_resources = ARRAY_SIZE(pxa168_u2o_resources),
- .dev = {
- .dma_mask = &usb_dma_mask,
- .coherent_dma_mask = 0xffffffff,
- }
-};
-#endif /* CONFIG_USB_MV_UDC */
-
-#if IS_ENABLED(CONFIG_USB_EHCI_MV_U2O)
-static struct resource pxa168_u2oehci_resources[] = {
- [0] = {
- .start = PXA168_U2O_REGBASE,
- .end = PXA168_U2O_REGBASE + USB_REG_RANGE,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_PXA168_USB1,
- .end = IRQ_PXA168_USB1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device pxa168_device_u2oehci = {
- .name = "pxa-u2oehci",
- .id = -1,
- .dev = {
- .dma_mask = &usb_dma_mask,
- .coherent_dma_mask = 0xffffffff,
- },
-
- .num_resources = ARRAY_SIZE(pxa168_u2oehci_resources),
- .resource = pxa168_u2oehci_resources,
-};
-#endif
-
-#if IS_ENABLED(CONFIG_USB_MV_OTG)
-static struct resource pxa168_u2ootg_resources[] = {
- /* regbase */
- [0] = {
- .start = PXA168_U2O_REGBASE + U2x_CAPREGS_OFFSET,
- .end = PXA168_U2O_REGBASE + USB_REG_RANGE,
- .flags = IORESOURCE_MEM,
- .name = "capregs",
- },
- /* phybase */
- [1] = {
- .start = PXA168_U2O_PHYBASE,
- .end = PXA168_U2O_PHYBASE + USB_PHY_RANGE,
- .flags = IORESOURCE_MEM,
- .name = "phyregs",
- },
- [2] = {
- .start = IRQ_PXA168_USB1,
- .end = IRQ_PXA168_USB1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device pxa168_device_u2ootg = {
- .name = "mv-otg",
- .id = -1,
- .dev = {
- .dma_mask = &usb_dma_mask,
- .coherent_dma_mask = 0xffffffff,
- },
-
- .num_resources = ARRAY_SIZE(pxa168_u2ootg_resources),
- .resource = pxa168_u2ootg_resources,
-};
-#endif /* CONFIG_USB_MV_OTG */
-
-#endif
diff --git a/arch/arm/mach-mmp/devices.h b/arch/arm/mach-mmp/devices.h
deleted file mode 100644
index d4920ebfebc5..000000000000
--- a/arch/arm/mach-mmp/devices.h
+++ /dev/null
@@ -1,57 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __MACH_DEVICE_H
-#define __MACH_DEVICE_H
-
-#include <linux/types.h>
-
-#define MAX_RESOURCE_DMA 2
-
-/* structure for describing the on-chip devices */
-struct mmp_device_desc {
- const char *dev_name;
- const char *drv_name;
- int id;
- int irq;
- unsigned long start;
- unsigned long size;
- int dma[MAX_RESOURCE_DMA];
-};
-
-#define PXA168_DEVICE(_name, _drv, _id, _irq, _start, _size, _dma...) \
-struct mmp_device_desc pxa168_device_##_name __initdata = { \
- .dev_name = "pxa168-" #_name, \
- .drv_name = _drv, \
- .id = _id, \
- .irq = IRQ_PXA168_##_irq, \
- .start = _start, \
- .size = _size, \
- .dma = { _dma }, \
-};
-
-#define PXA910_DEVICE(_name, _drv, _id, _irq, _start, _size, _dma...) \
-struct mmp_device_desc pxa910_device_##_name __initdata = { \
- .dev_name = "pxa910-" #_name, \
- .drv_name = _drv, \
- .id = _id, \
- .irq = IRQ_PXA910_##_irq, \
- .start = _start, \
- .size = _size, \
- .dma = { _dma }, \
-};
-
-#define MMP2_DEVICE(_name, _drv, _id, _irq, _start, _size, _dma...) \
-struct mmp_device_desc mmp2_device_##_name __initdata = { \
- .dev_name = "mmp2-" #_name, \
- .drv_name = _drv, \
- .id = _id, \
- .irq = IRQ_MMP2_##_irq, \
- .start = _start, \
- .size = _size, \
- .dma = { _dma }, \
-}
-
-extern int mmp_register_device(struct mmp_device_desc *, void *, size_t);
-extern int pxa_usb_phy_init(void __iomem *phy_reg);
-extern void pxa_usb_phy_deinit(void __iomem *phy_reg);
-
-#endif /* __MACH_DEVICE_H */
diff --git a/arch/arm/mach-mmp/irqs.h b/arch/arm/mach-mmp/irqs.h
index 5acc4d532a43..b8446a17ea55 100644
--- a/arch/arm/mach-mmp/irqs.h
+++ b/arch/arm/mach-mmp/irqs.h
@@ -2,56 +2,6 @@
#ifndef __ASM_MACH_IRQS_H
#define __ASM_MACH_IRQS_H
-/*
- * Interrupt numbers for PXA168
- */
-#define IRQ_PXA168_NONE (-1)
-#define IRQ_PXA168_SSP4 0
-#define IRQ_PXA168_SSP3 1
-#define IRQ_PXA168_SSP2 2
-#define IRQ_PXA168_SSP1 3
-#define IRQ_PXA168_PMIC_INT 4
-#define IRQ_PXA168_RTC_INT 5
-#define IRQ_PXA168_RTC_ALARM 6
-#define IRQ_PXA168_TWSI0 7
-#define IRQ_PXA168_GPU 8
-#define IRQ_PXA168_KEYPAD 9
-#define IRQ_PXA168_ONEWIRE 12
-#define IRQ_PXA168_TIMER1 13
-#define IRQ_PXA168_TIMER2 14
-#define IRQ_PXA168_TIMER3 15
-#define IRQ_PXA168_CMU 16
-#define IRQ_PXA168_SSP5 17
-#define IRQ_PXA168_MSP_WAKEUP 19
-#define IRQ_PXA168_CF_WAKEUP 20
-#define IRQ_PXA168_XD_WAKEUP 21
-#define IRQ_PXA168_MFU 22
-#define IRQ_PXA168_MSP 23
-#define IRQ_PXA168_CF 24
-#define IRQ_PXA168_XD 25
-#define IRQ_PXA168_DDR_INT 26
-#define IRQ_PXA168_UART1 27
-#define IRQ_PXA168_UART2 28
-#define IRQ_PXA168_UART3 29
-#define IRQ_PXA168_WDT 35
-#define IRQ_PXA168_MAIN_PMU 36
-#define IRQ_PXA168_FRQ_CHANGE 38
-#define IRQ_PXA168_SDH1 39
-#define IRQ_PXA168_SDH2 40
-#define IRQ_PXA168_LCD 41
-#define IRQ_PXA168_CI 42
-#define IRQ_PXA168_USB1 44
-#define IRQ_PXA168_NAND 45
-#define IRQ_PXA168_HIFI_DMA 46
-#define IRQ_PXA168_DMA_INT0 47
-#define IRQ_PXA168_DMA_INT1 48
-#define IRQ_PXA168_GPIOX 49
-#define IRQ_PXA168_USB2 51
-#define IRQ_PXA168_AC97 57
-#define IRQ_PXA168_TWSI1 58
-#define IRQ_PXA168_AP_PMU 60
-#define IRQ_PXA168_SM_INT 63
-
/*
* Interrupt numbers for PXA910
*/
@@ -114,127 +64,4 @@
#define IRQ_PXA910_AP_PMU 60
#define IRQ_PXA910_SM_INT 63 /* from PinMux */
-/*
- * Interrupt numbers for MMP2
- */
-#define IRQ_MMP2_NONE (-1)
-#define IRQ_MMP2_SSP1 0
-#define IRQ_MMP2_SSP2 1
-#define IRQ_MMP2_SSPA1 2
-#define IRQ_MMP2_SSPA2 3
-#define IRQ_MMP2_PMIC_MUX 4 /* PMIC & Charger */
-#define IRQ_MMP2_RTC_MUX 5
-#define IRQ_MMP2_TWSI1 7
-#define IRQ_MMP2_GPU 8
-#define IRQ_MMP2_KEYPAD_MUX 9
-#define IRQ_MMP2_ROTARY 10
-#define IRQ_MMP2_TRACKBALL 11
-#define IRQ_MMP2_ONEWIRE 12
-#define IRQ_MMP2_TIMER1 13
-#define IRQ_MMP2_TIMER2 14
-#define IRQ_MMP2_TIMER3 15
-#define IRQ_MMP2_RIPC 16
-#define IRQ_MMP2_TWSI_MUX 17 /* TWSI2 ~ TWSI6 */
-#define IRQ_MMP2_HDMI 19
-#define IRQ_MMP2_SSP3 20
-#define IRQ_MMP2_SSP4 21
-#define IRQ_MMP2_USB_HS1 22
-#define IRQ_MMP2_USB_HS2 23
-#define IRQ_MMP2_UART3 24
-#define IRQ_MMP2_UART1 27
-#define IRQ_MMP2_UART2 28
-#define IRQ_MMP2_MIPI_DSI 29
-#define IRQ_MMP2_CI2 30
-#define IRQ_MMP2_PMU_TIMER1 31
-#define IRQ_MMP2_PMU_TIMER2 32
-#define IRQ_MMP2_PMU_TIMER3 33
-#define IRQ_MMP2_USB_FS 34
-#define IRQ_MMP2_MISC_MUX 35
-#define IRQ_MMP2_WDT1 36
-#define IRQ_MMP2_NAND_DMA 37
-#define IRQ_MMP2_USIM 38
-#define IRQ_MMP2_MMC 39
-#define IRQ_MMP2_WTM 40
-#define IRQ_MMP2_LCD 41
-#define IRQ_MMP2_CI 42
-#define IRQ_MMP2_IRE 43
-#define IRQ_MMP2_USB_OTG 44
-#define IRQ_MMP2_NAND 45
-#define IRQ_MMP2_UART4 46
-#define IRQ_MMP2_DMA_FIQ 47
-#define IRQ_MMP2_DMA_RIQ 48
-#define IRQ_MMP2_GPIO 49
-#define IRQ_MMP2_MIPI_HSI1_MUX 51
-#define IRQ_MMP2_MMC2 52
-#define IRQ_MMP2_MMC3 53
-#define IRQ_MMP2_MMC4 54
-#define IRQ_MMP2_MIPI_HSI0_MUX 55
-#define IRQ_MMP2_MSP 58
-#define IRQ_MMP2_MIPI_SLIM_DMA 59
-#define IRQ_MMP2_PJ4_FREQ_CHG 60
-#define IRQ_MMP2_MIPI_SLIM 62
-#define IRQ_MMP2_SM 63
-
-#define IRQ_MMP2_MUX_BASE 64
-
-/* secondary interrupt of INT #4 */
-#define IRQ_MMP2_PMIC_BASE (IRQ_MMP2_MUX_BASE)
-#define IRQ_MMP2_CHARGER (IRQ_MMP2_PMIC_BASE + 0)
-#define IRQ_MMP2_PMIC (IRQ_MMP2_PMIC_BASE + 1)
-
-/* secondary interrupt of INT #5 */
-#define IRQ_MMP2_RTC_BASE (IRQ_MMP2_PMIC_BASE + 2)
-#define IRQ_MMP2_RTC_ALARM (IRQ_MMP2_RTC_BASE + 0)
-#define IRQ_MMP2_RTC (IRQ_MMP2_RTC_BASE + 1)
-
-/* secondary interrupt of INT #9 */
-#define IRQ_MMP2_KEYPAD_BASE (IRQ_MMP2_RTC_BASE + 2)
-#define IRQ_MMP2_KPC (IRQ_MMP2_KEYPAD_BASE + 0)
-#define IRQ_MMP2_ROTORY (IRQ_MMP2_KEYPAD_BASE + 1)
-#define IRQ_MMP2_TBALL (IRQ_MMP2_KEYPAD_BASE + 2)
-
-/* secondary interrupt of INT #17 */
-#define IRQ_MMP2_TWSI_BASE (IRQ_MMP2_KEYPAD_BASE + 3)
-#define IRQ_MMP2_TWSI2 (IRQ_MMP2_TWSI_BASE + 0)
-#define IRQ_MMP2_TWSI3 (IRQ_MMP2_TWSI_BASE + 1)
-#define IRQ_MMP2_TWSI4 (IRQ_MMP2_TWSI_BASE + 2)
-#define IRQ_MMP2_TWSI5 (IRQ_MMP2_TWSI_BASE + 3)
-#define IRQ_MMP2_TWSI6 (IRQ_MMP2_TWSI_BASE + 4)
-
-/* secondary interrupt of INT #35 */
-#define IRQ_MMP2_MISC_BASE (IRQ_MMP2_TWSI_BASE + 5)
-#define IRQ_MMP2_PERF (IRQ_MMP2_MISC_BASE + 0)
-#define IRQ_MMP2_L2_PA_ECC (IRQ_MMP2_MISC_BASE + 1)
-#define IRQ_MMP2_L2_ECC (IRQ_MMP2_MISC_BASE + 2)
-#define IRQ_MMP2_L2_UECC (IRQ_MMP2_MISC_BASE + 3)
-#define IRQ_MMP2_DDR (IRQ_MMP2_MISC_BASE + 4)
-#define IRQ_MMP2_FAB0_TIMEOUT (IRQ_MMP2_MISC_BASE + 5)
-#define IRQ_MMP2_FAB1_TIMEOUT (IRQ_MMP2_MISC_BASE + 6)
-#define IRQ_MMP2_FAB2_TIMEOUT (IRQ_MMP2_MISC_BASE + 7)
-#define IRQ_MMP2_THERMAL (IRQ_MMP2_MISC_BASE + 9)
-#define IRQ_MMP2_MAIN_PMU (IRQ_MMP2_MISC_BASE + 10)
-#define IRQ_MMP2_WDT2 (IRQ_MMP2_MISC_BASE + 11)
-#define IRQ_MMP2_CORESIGHT (IRQ_MMP2_MISC_BASE + 12)
-#define IRQ_MMP2_COMMTX (IRQ_MMP2_MISC_BASE + 13)
-#define IRQ_MMP2_COMMRX (IRQ_MMP2_MISC_BASE + 14)
-
-/* secondary interrupt of INT #51 */
-#define IRQ_MMP2_MIPI_HSI1_BASE (IRQ_MMP2_MISC_BASE + 15)
-#define IRQ_MMP2_HSI1_CAWAKE (IRQ_MMP2_MIPI_HSI1_BASE + 0)
-#define IRQ_MMP2_MIPI_HSI_INT1 (IRQ_MMP2_MIPI_HSI1_BASE + 1)
-
-/* secondary interrupt of INT #55 */
-#define IRQ_MMP2_MIPI_HSI0_BASE (IRQ_MMP2_MIPI_HSI1_BASE + 2)
-#define IRQ_MMP2_HSI0_CAWAKE (IRQ_MMP2_MIPI_HSI0_BASE + 0)
-#define IRQ_MMP2_MIPI_HSI_INT0 (IRQ_MMP2_MIPI_HSI0_BASE + 1)
-
-#define IRQ_MMP2_MUX_END (IRQ_MMP2_MIPI_HSI0_BASE + 2)
-
-#define IRQ_GPIO_START 128
-#define MMP_NR_BUILTIN_GPIO 192
-#define MMP_GPIO_TO_IRQ(gpio) (IRQ_GPIO_START + (gpio))
-
-#define IRQ_BOARD_START (IRQ_GPIO_START + MMP_NR_BUILTIN_GPIO)
-#define MMP_NR_IRQS IRQ_BOARD_START
-
#endif /* __ASM_MACH_IRQS_H */
diff --git a/arch/arm/mach-mmp/mfp.h b/arch/arm/mach-mmp/mfp.h
deleted file mode 100644
index 6f3057987756..000000000000
--- a/arch/arm/mach-mmp/mfp.h
+++ /dev/null
@@ -1,35 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __ASM_MACH_MFP_H
-#define __ASM_MACH_MFP_H
-
-#include <linux/soc/pxa/mfp.h>
-
-/*
- * NOTE: the MFPR register bit definitions on PXA168 processor lines are a
- * bit different from those on PXA3xx. Bit [7:10] are now reserved, which
- * were SLEEP_OE_N, SLEEP_DATA, SLEEP_SEL and the LSB of DRIVE bits.
- *
- * To cope with this difference and re-use the pxa3xx mfp code as much as
- * possible, we make the following compromise:
- *
- * 1. SLEEP_OE_N will always be programmed to '1' (by MFP_LPM_FLOAT)
- * 2. DRIVE strength definitions redefined to include the reserved bit
- * - the reserved bit differs between pxa168 and pxa910, and the
- * MFP_DRIVE_* macros are individually defined in mfp-pxa{168,910}.h
- * 3. Override MFP_CFG() and MFP_CFG_DRV()
- * 4. Drop the use of MFP_CFG_LPM() and MFP_CFG_X()
- */
-
-#undef MFP_CFG
-#undef MFP_CFG_DRV
-#undef MFP_CFG_LPM
-#undef MFP_CFG_X
-#undef MFP_CFG_DEFAULT
-
-#define MFP_CFG(pin, af) \
- (MFP_LPM_FLOAT | MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_DRIVE_MEDIUM)
-
-#define MFP_CFG_DRV(pin, af, drv) \
- (MFP_LPM_FLOAT | MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_DRIVE_##drv)
-
-#endif /* __ASM_MACH_MFP_H */
diff --git a/arch/arm/mach-mmp/mmp2.c b/arch/arm/mach-mmp/mmp2.c
index bbc4c2274de3..8ee6a4547731 100644
--- a/arch/arm/mach-mmp/mmp2.c
+++ b/arch/arm/mach-mmp/mmp2.c
@@ -19,11 +19,8 @@
#include <asm/mach/time.h>
#include "addr-map.h"
-#include "regs-apbc.h"
#include <linux/soc/mmp/cputype.h>
-#include "irqs.h"
-#include "mfp.h"
-#include "devices.h"
+#include <linux/soc/pxa/mfp.h>
#include "mmp2.h"
#include "pm-mmp2.h"
@@ -91,14 +88,6 @@ void mmp2_clear_pmic_int(void)
__raw_writel(data, mfpr_pmic);
}
-void __init mmp2_init_irq(void)
-{
- mmp2_init_icu();
-#ifdef CONFIG_PM
- icu_irq_chip.irq_set_wake = mmp2_set_wake;
-#endif
-}
-
static int __init mmp2_init(void)
{
if (cpu_is_mmp2()) {
@@ -115,61 +104,3 @@ static int __init mmp2_init(void)
return 0;
}
postcore_initcall(mmp2_init);
-
-#define APBC_TIMERS APBC_REG(0x024)
-
-void __init mmp2_timer_init(void)
-{
- unsigned long clk_rst;
-
- __raw_writel(APBC_APBCLK | APBC_RST, APBC_TIMERS);
-
- /*
- * enable bus/functional clock, enable 6.5MHz (divider 4),
- * release reset
- */
- clk_rst = APBC_APBCLK | APBC_FNCLK | APBC_FNCLKSEL(1);
- __raw_writel(clk_rst, APBC_TIMERS);
-
- mmp_timer_init(IRQ_MMP2_TIMER1, 6500000);
-}
-
-/* on-chip devices */
-MMP2_DEVICE(uart1, "pxa2xx-uart", 0, UART1, 0xd4030000, 0x30, 4, 5);
-MMP2_DEVICE(uart2, "pxa2xx-uart", 1, UART2, 0xd4017000, 0x30, 20, 21);
-MMP2_DEVICE(uart3, "pxa2xx-uart", 2, UART3, 0xd4018000, 0x30, 22, 23);
-MMP2_DEVICE(uart4, "pxa2xx-uart", 3, UART4, 0xd4016000, 0x30, 18, 19);
-MMP2_DEVICE(twsi1, "pxa2xx-i2c", 0, TWSI1, 0xd4011000, 0x70);
-MMP2_DEVICE(twsi2, "pxa2xx-i2c", 1, TWSI2, 0xd4031000, 0x70);
-MMP2_DEVICE(twsi3, "pxa2xx-i2c", 2, TWSI3, 0xd4032000, 0x70);
-MMP2_DEVICE(twsi4, "pxa2xx-i2c", 3, TWSI4, 0xd4033000, 0x70);
-MMP2_DEVICE(twsi5, "pxa2xx-i2c", 4, TWSI5, 0xd4033800, 0x70);
-MMP2_DEVICE(twsi6, "pxa2xx-i2c", 5, TWSI6, 0xd4034000, 0x70);
-MMP2_DEVICE(nand, "pxa3xx-nand", -1, NAND, 0xd4283000, 0x100, 28, 29);
-MMP2_DEVICE(sdh0, "sdhci-pxav3", 0, MMC, 0xd4280000, 0x120);
-MMP2_DEVICE(sdh1, "sdhci-pxav3", 1, MMC2, 0xd4280800, 0x120);
-MMP2_DEVICE(sdh2, "sdhci-pxav3", 2, MMC3, 0xd4281000, 0x120);
-MMP2_DEVICE(sdh3, "sdhci-pxav3", 3, MMC4, 0xd4281800, 0x120);
-MMP2_DEVICE(asram, "asram", -1, NONE, 0xe0000000, 0x4000);
-/* 0xd1000000 ~ 0xd101ffff is reserved for secure processor */
-MMP2_DEVICE(isram, "isram", -1, NONE, 0xd1020000, 0x18000);
-
-struct resource mmp2_resource_gpio[] = {
- {
- .start = 0xd4019000,
- .end = 0xd4019fff,
- .flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_MMP2_GPIO,
- .end = IRQ_MMP2_GPIO,
- .name = "gpio_mux",
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device mmp2_device_gpio = {
- .name = "mmp2-gpio",
- .id = -1,
- .num_resources = ARRAY_SIZE(mmp2_resource_gpio),
- .resource = mmp2_resource_gpio,
-};
diff --git a/arch/arm/mach-mmp/mmp2.h b/arch/arm/mach-mmp/mmp2.h
index 5c80836aea76..6616d3f7a0ac 100644
--- a/arch/arm/mach-mmp/mmp2.h
+++ b/arch/arm/mach-mmp/mmp2.h
@@ -2,90 +2,7 @@
#ifndef __ASM_MACH_MMP2_H
#define __ASM_MACH_MMP2_H
-#include <linux/platform_data/pxa_sdhci.h>
-
-extern void mmp2_timer_init(void);
-extern void __init mmp2_init_irq(void);
extern void mmp2_clear_pmic_int(void);
-#include <linux/i2c.h>
-#include <linux/platform_data/i2c-pxa.h>
-#include <linux/irqchip/mmp.h>
-
-#include "devices.h"
-
-extern struct mmp_device_desc mmp2_device_uart1;
-extern struct mmp_device_desc mmp2_device_uart2;
-extern struct mmp_device_desc mmp2_device_uart3;
-extern struct mmp_device_desc mmp2_device_uart4;
-extern struct mmp_device_desc mmp2_device_twsi1;
-extern struct mmp_device_desc mmp2_device_twsi2;
-extern struct mmp_device_desc mmp2_device_twsi3;
-extern struct mmp_device_desc mmp2_device_twsi4;
-extern struct mmp_device_desc mmp2_device_twsi5;
-extern struct mmp_device_desc mmp2_device_twsi6;
-extern struct mmp_device_desc mmp2_device_sdh0;
-extern struct mmp_device_desc mmp2_device_sdh1;
-extern struct mmp_device_desc mmp2_device_sdh2;
-extern struct mmp_device_desc mmp2_device_sdh3;
-
-extern struct platform_device mmp2_device_gpio;
-
-static inline int mmp2_add_uart(int id)
-{
- struct mmp_device_desc *d = NULL;
-
- switch (id) {
- case 1: d = &mmp2_device_uart1; break;
- case 2: d = &mmp2_device_uart2; break;
- case 3: d = &mmp2_device_uart3; break;
- case 4: d = &mmp2_device_uart4; break;
- default:
- return -EINVAL;
- }
-
- return mmp_register_device(d, NULL, 0);
-}
-
-static inline int mmp2_add_twsi(int id, struct i2c_pxa_platform_data *data,
- struct i2c_board_info *info, unsigned size)
-{
- struct mmp_device_desc *d = NULL;
- int ret;
-
- switch (id) {
- case 1: d = &mmp2_device_twsi1; break;
- case 2: d = &mmp2_device_twsi2; break;
- case 3: d = &mmp2_device_twsi3; break;
- case 4: d = &mmp2_device_twsi4; break;
- case 5: d = &mmp2_device_twsi5; break;
- case 6: d = &mmp2_device_twsi6; break;
- default:
- return -EINVAL;
- }
-
- ret = i2c_register_board_info(id - 1, info, size);
- if (ret)
- return ret;
-
- return mmp_register_device(d, data, sizeof(*data));
-}
-
-static inline int mmp2_add_sdhost(int id, struct sdhci_pxa_platdata *data)
-{
- struct mmp_device_desc *d = NULL;
-
- switch (id) {
- case 0: d = &mmp2_device_sdh0; break;
- case 1: d = &mmp2_device_sdh1; break;
- case 2: d = &mmp2_device_sdh2; break;
- case 3: d = &mmp2_device_sdh3; break;
- default:
- return -EINVAL;
- }
-
- return mmp_register_device(d, data, sizeof(*data));
-}
-
#endif /* __ASM_MACH_MMP2_H */
diff --git a/arch/arm/mach-mmp/pm-mmp2.c b/arch/arm/mach-mmp/pm-mmp2.c
index 7a6f74c32d42..bd6563962d77 100644
--- a/arch/arm/mach-mmp/pm-mmp2.c
+++ b/arch/arm/mach-mmp/pm-mmp2.c
@@ -21,40 +21,6 @@
#include "addr-map.h"
#include "pm-mmp2.h"
#include "regs-icu.h"
-#include "irqs.h"
-
-int mmp2_set_wake(struct irq_data *d, unsigned int on)
-{
- unsigned long data = 0;
- int irq = d->irq;
-
- /* enable wakeup sources */
- switch (irq) {
- case IRQ_MMP2_RTC:
- case IRQ_MMP2_RTC_ALARM:
- data = MPMU_WUCRM_PJ_WAKEUP(4) | MPMU_WUCRM_PJ_RTC_ALARM;
- break;
- case IRQ_MMP2_PMIC:
- data = MPMU_WUCRM_PJ_WAKEUP(7);
- break;
- case IRQ_MMP2_MMC2:
- /* mmc use WAKEUP2, same as GPIO wakeup source */
- data = MPMU_WUCRM_PJ_WAKEUP(2);
- break;
- }
- if (on) {
- if (data) {
- data |= __raw_readl(MPMU_WUCRM_PJ);
- __raw_writel(data, MPMU_WUCRM_PJ);
- }
- } else {
- if (data) {
- data = ~data & __raw_readl(MPMU_WUCRM_PJ);
- __raw_writel(data, MPMU_WUCRM_PJ);
- }
- }
- return 0;
-}
static void pm_scu_clk_disable(void)
{
diff --git a/arch/arm/mach-mmp/pm-mmp2.h b/arch/arm/mach-mmp/pm-mmp2.h
index 70299a9450d3..70cff8bf0cc8 100644
--- a/arch/arm/mach-mmp/pm-mmp2.h
+++ b/arch/arm/mach-mmp/pm-mmp2.h
@@ -55,5 +55,5 @@ enum {
};
extern void mmp2_pm_enter_lowpower_mode(int state);
-extern int mmp2_set_wake(struct irq_data *d, unsigned int on);
+
#endif
diff --git a/arch/arm/mach-mmp/pm-pxa910.c b/arch/arm/mach-mmp/pm-pxa910.c
index 1d71d73c1862..f6ba6db0aa36 100644
--- a/arch/arm/mach-mmp/pm-pxa910.c
+++ b/arch/arm/mach-mmp/pm-pxa910.c
@@ -22,112 +22,6 @@
#include "addr-map.h"
#include "pm-pxa910.h"
#include "regs-icu.h"
-#include "irqs.h"
-
-int pxa910_set_wake(struct irq_data *data, unsigned int on)
-{
- uint32_t awucrm = 0, apcr = 0;
- int irq = data->irq;
-
- /* setting wakeup sources */
- switch (irq) {
- /* wakeup line 2 */
- case IRQ_PXA910_AP_GPIO:
- awucrm = MPMU_AWUCRM_WAKEUP(2);
- apcr |= MPMU_APCR_SLPWP2;
- break;
- /* wakeup line 3 */
- case IRQ_PXA910_KEYPAD:
- awucrm = MPMU_AWUCRM_WAKEUP(3) | MPMU_AWUCRM_KEYPRESS;
- apcr |= MPMU_APCR_SLPWP3;
- break;
- case IRQ_PXA910_ROTARY:
- awucrm = MPMU_AWUCRM_WAKEUP(3) | MPMU_AWUCRM_NEWROTARY;
- apcr |= MPMU_APCR_SLPWP3;
- break;
- case IRQ_PXA910_TRACKBALL:
- awucrm = MPMU_AWUCRM_WAKEUP(3) | MPMU_AWUCRM_TRACKBALL;
- apcr |= MPMU_APCR_SLPWP3;
- break;
- /* wakeup line 4 */
- case IRQ_PXA910_AP1_TIMER1:
- awucrm = MPMU_AWUCRM_WAKEUP(4) | MPMU_AWUCRM_AP1_TIMER_1;
- apcr |= MPMU_APCR_SLPWP4;
- break;
- case IRQ_PXA910_AP1_TIMER2:
- awucrm = MPMU_AWUCRM_WAKEUP(4) | MPMU_AWUCRM_AP1_TIMER_2;
- apcr |= MPMU_APCR_SLPWP4;
- break;
- case IRQ_PXA910_AP1_TIMER3:
- awucrm = MPMU_AWUCRM_WAKEUP(4) | MPMU_AWUCRM_AP1_TIMER_3;
- apcr |= MPMU_APCR_SLPWP4;
- break;
- case IRQ_PXA910_AP2_TIMER1:
- awucrm = MPMU_AWUCRM_WAKEUP(4) | MPMU_AWUCRM_AP2_TIMER_1;
- apcr |= MPMU_APCR_SLPWP4;
- break;
- case IRQ_PXA910_AP2_TIMER2:
- awucrm = MPMU_AWUCRM_WAKEUP(4) | MPMU_AWUCRM_AP2_TIMER_2;
- apcr |= MPMU_APCR_SLPWP4;
- break;
- case IRQ_PXA910_AP2_TIMER3:
- awucrm = MPMU_AWUCRM_WAKEUP(4) | MPMU_AWUCRM_AP2_TIMER_3;
- apcr |= MPMU_APCR_SLPWP4;
- break;
- case IRQ_PXA910_RTC_ALARM:
- awucrm = MPMU_AWUCRM_WAKEUP(4) | MPMU_AWUCRM_RTC_ALARM;
- apcr |= MPMU_APCR_SLPWP4;
- break;
- /* wakeup line 5 */
- case IRQ_PXA910_USB1:
- case IRQ_PXA910_USB2:
- awucrm = MPMU_AWUCRM_WAKEUP(5);
- apcr |= MPMU_APCR_SLPWP5;
- break;
- /* wakeup line 6 */
- case IRQ_PXA910_MMC:
- awucrm = MPMU_AWUCRM_WAKEUP(6)
- | MPMU_AWUCRM_SDH1
- | MPMU_AWUCRM_SDH2;
- apcr |= MPMU_APCR_SLPWP6;
- break;
- /* wakeup line 7 */
- case IRQ_PXA910_PMIC_INT:
- awucrm = MPMU_AWUCRM_WAKEUP(7);
- apcr |= MPMU_APCR_SLPWP7;
- break;
- default:
- if (irq >= IRQ_GPIO_START && irq < IRQ_BOARD_START) {
- awucrm = MPMU_AWUCRM_WAKEUP(2);
- apcr |= MPMU_APCR_SLPWP2;
- } else {
- /* FIXME: This should return a proper error code ! */
- printk(KERN_ERR "Error: no defined wake up source irq: %d\n",
- irq);
- }
- }
-
- if (on) {
- if (awucrm) {
- awucrm |= __raw_readl(MPMU_AWUCRM);
- __raw_writel(awucrm, MPMU_AWUCRM);
- }
- if (apcr) {
- apcr = ~apcr & __raw_readl(MPMU_APCR);
- __raw_writel(apcr, MPMU_APCR);
- }
- } else {
- if (awucrm) {
- awucrm = ~awucrm & __raw_readl(MPMU_AWUCRM);
- __raw_writel(awucrm, MPMU_AWUCRM);
- }
- if (apcr) {
- apcr |= __raw_readl(MPMU_APCR);
- __raw_writel(apcr, MPMU_APCR);
- }
- }
- return 0;
-}
void pxa910_pm_enter_lowpower_mode(int state)
{
diff --git a/arch/arm/mach-mmp/pxa168.c b/arch/arm/mach-mmp/pxa168.c
index 1e9389245d0e..565d4a6c3bd5 100644
--- a/arch/arm/mach-mmp/pxa168.c
+++ b/arch/arm/mach-mmp/pxa168.c
@@ -12,7 +12,6 @@
#include <linux/clk.h>
#include <linux/clk/mmp.h>
#include <linux/platform_device.h>
-#include <linux/platform_data/mv_usb.h>
#include <linux/dma-mapping.h>
#include <asm/mach/time.h>
@@ -21,13 +20,9 @@
#include "addr-map.h"
#include "common.h"
#include <linux/soc/mmp/cputype.h>
+#include <linux/soc/pxa/mfp.h>
#include "devices.h"
-#include "irqs.h"
-#include "mfp.h"
#include "pxa168.h"
-#include "regs-apbc.h"
-#include "regs-apmu.h"
-#include "regs-usb.h"
#define MFPR_VIRT_BASE (APB_VIRT_BASE + 0x1e000)
@@ -41,11 +36,6 @@ static struct mfp_addr_map pxa168_mfp_addr_map[] __initdata =
MFP_ADDR_END,
};
-void __init pxa168_init_irq(void)
-{
- icu_init_irq();
-}
-
static int __init pxa168_init(void)
{
if (cpu_is_pxa168()) {
@@ -59,117 +49,3 @@ static int __init pxa168_init(void)
return 0;
}
postcore_initcall(pxa168_init);
-
-/* system timer - clock enabled, 3.25MHz */
-#define TIMER_CLK_RST (APBC_APBCLK | APBC_FNCLK | APBC_FNCLKSEL(3))
-#define APBC_TIMERS APBC_REG(0x34)
-
-void __init pxa168_timer_init(void)
-{
- /* this is early, we have to initialize the CCU registers by
- * ourselves instead of using clk_* API. Clock rate is defined
- * by APBC_TIMERS_CLK_RST (3.25MHz) and enabled free-running
- */
- __raw_writel(APBC_APBCLK | APBC_RST, APBC_TIMERS);
-
- /* 3.25MHz, bus/functional clock enabled, release reset */
- __raw_writel(TIMER_CLK_RST, APBC_TIMERS);
-
- mmp_timer_init(IRQ_PXA168_TIMER1, 3250000);
-}
-
-void pxa168_clear_keypad_wakeup(void)
-{
- uint32_t val;
- uint32_t mask = APMU_PXA168_KP_WAKE_CLR;
-
- /* wake event clear is needed in order to clear keypad interrupt */
- val = __raw_readl(APMU_WAKE_CLR);
- __raw_writel(val | mask, APMU_WAKE_CLR);
-}
-
-/* on-chip devices */
-PXA168_DEVICE(uart1, "pxa2xx-uart", 0, UART1, 0xd4017000, 0x30, 21, 22);
-PXA168_DEVICE(uart2, "pxa2xx-uart", 1, UART2, 0xd4018000, 0x30, 23, 24);
-PXA168_DEVICE(uart3, "pxa2xx-uart", 2, UART3, 0xd4026000, 0x30, 23, 24);
-PXA168_DEVICE(twsi0, "pxa2xx-i2c", 0, TWSI0, 0xd4011000, 0x28);
-PXA168_DEVICE(twsi1, "pxa2xx-i2c", 1, TWSI1, 0xd4025000, 0x28);
-PXA168_DEVICE(pwm1, "pxa168-pwm", 0, NONE, 0xd401a000, 0x10);
-PXA168_DEVICE(pwm2, "pxa168-pwm", 1, NONE, 0xd401a400, 0x10);
-PXA168_DEVICE(pwm3, "pxa168-pwm", 2, NONE, 0xd401a800, 0x10);
-PXA168_DEVICE(pwm4, "pxa168-pwm", 3, NONE, 0xd401ac00, 0x10);
-PXA168_DEVICE(nand, "pxa3xx-nand", -1, NAND, 0xd4283000, 0x80, 97, 99);
-PXA168_DEVICE(ssp1, "pxa168-ssp", 0, SSP1, 0xd401b000, 0x40, 52, 53);
-PXA168_DEVICE(ssp2, "pxa168-ssp", 1, SSP2, 0xd401c000, 0x40, 54, 55);
-PXA168_DEVICE(ssp3, "pxa168-ssp", 2, SSP3, 0xd401f000, 0x40, 56, 57);
-PXA168_DEVICE(ssp4, "pxa168-ssp", 3, SSP4, 0xd4020000, 0x40, 58, 59);
-PXA168_DEVICE(ssp5, "pxa168-ssp", 4, SSP5, 0xd4021000, 0x40, 60, 61);
-PXA168_DEVICE(fb, "pxa168-fb", -1, LCD, 0xd420b000, 0x1c8);
-PXA168_DEVICE(keypad, "pxa27x-keypad", -1, KEYPAD, 0xd4012000, 0x4c);
-PXA168_DEVICE(eth, "pxa168-eth", -1, MFU, 0xc0800000, 0x0fff);
-
-struct resource pxa168_resource_gpio[] = {
- {
- .start = 0xd4019000,
- .end = 0xd4019fff,
- .flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_PXA168_GPIOX,
- .end = IRQ_PXA168_GPIOX,
- .name = "gpio_mux",
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device pxa168_device_gpio = {
- .name = "mmp-gpio",
- .id = -1,
- .num_resources = ARRAY_SIZE(pxa168_resource_gpio),
- .resource = pxa168_resource_gpio,
-};
-
-struct resource pxa168_usb_host_resources[] = {
- /* USB Host conroller register base */
- [0] = {
- .start = PXA168_U2H_REGBASE + U2x_CAPREGS_OFFSET,
- .end = PXA168_U2H_REGBASE + USB_REG_RANGE,
- .flags = IORESOURCE_MEM,
- .name = "capregs",
- },
- /* USB PHY register base */
- [1] = {
- .start = PXA168_U2H_PHYBASE,
- .end = PXA168_U2H_PHYBASE + USB_PHY_RANGE,
- .flags = IORESOURCE_MEM,
- .name = "phyregs",
- },
- [2] = {
- .start = IRQ_PXA168_USB2,
- .end = IRQ_PXA168_USB2,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static u64 pxa168_usb_host_dmamask = DMA_BIT_MASK(32);
-struct platform_device pxa168_device_usb_host = {
- .name = "pxa-sph",
- .id = -1,
- .dev = {
- .dma_mask = &pxa168_usb_host_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
-
- .num_resources = ARRAY_SIZE(pxa168_usb_host_resources),
- .resource = pxa168_usb_host_resources,
-};
-
-int __init pxa168_add_usb_host(struct mv_usb_platform_data *pdata)
-{
- pxa168_device_usb_host.dev.platform_data = pdata;
- return platform_device_register(&pxa168_device_usb_host);
-}
-
-void pxa168_restart(enum reboot_mode mode, const char *cmd)
-{
- soft_restart(0xffff0000);
-}
diff --git a/arch/arm/mach-mmp/pxa168.h b/arch/arm/mach-mmp/pxa168.h
index c1547e098f09..279783ef239d 100644
--- a/arch/arm/mach-mmp/pxa168.h
+++ b/arch/arm/mach-mmp/pxa168.h
@@ -10,130 +10,7 @@ extern void pxa168_restart(enum reboot_mode, const char *);
extern void pxa168_clear_keypad_wakeup(void);
#include <linux/i2c.h>
-#include <linux/platform_data/i2c-pxa.h>
-#include <linux/platform_data/mtd-nand-pxa3xx.h>
-#include <video/pxa168fb.h>
-#include <linux/platform_data/keypad-pxa27x.h>
-#include <linux/pxa168_eth.h>
-#include <linux/platform_data/mv_usb.h>
#include <linux/soc/mmp/cputype.h>
#include <linux/irqchip/mmp.h>
-#include "devices.h"
-
-extern struct mmp_device_desc pxa168_device_uart1;
-extern struct mmp_device_desc pxa168_device_uart2;
-extern struct mmp_device_desc pxa168_device_uart3;
-extern struct mmp_device_desc pxa168_device_twsi0;
-extern struct mmp_device_desc pxa168_device_twsi1;
-extern struct mmp_device_desc pxa168_device_pwm1;
-extern struct mmp_device_desc pxa168_device_pwm2;
-extern struct mmp_device_desc pxa168_device_pwm3;
-extern struct mmp_device_desc pxa168_device_pwm4;
-extern struct mmp_device_desc pxa168_device_ssp1;
-extern struct mmp_device_desc pxa168_device_ssp2;
-extern struct mmp_device_desc pxa168_device_ssp3;
-extern struct mmp_device_desc pxa168_device_ssp4;
-extern struct mmp_device_desc pxa168_device_ssp5;
-extern struct mmp_device_desc pxa168_device_nand;
-extern struct mmp_device_desc pxa168_device_fb;
-extern struct mmp_device_desc pxa168_device_keypad;
-extern struct mmp_device_desc pxa168_device_eth;
-
-/* pdata can be NULL */
-extern int __init pxa168_add_usb_host(struct mv_usb_platform_data *pdata);
-
-
-extern struct platform_device pxa168_device_gpio;
-
-static inline int pxa168_add_uart(int id)
-{
- struct mmp_device_desc *d = NULL;
-
- switch (id) {
- case 1: d = &pxa168_device_uart1; break;
- case 2: d = &pxa168_device_uart2; break;
- case 3: d = &pxa168_device_uart3; break;
- }
-
- if (d == NULL)
- return -EINVAL;
-
- return mmp_register_device(d, NULL, 0);
-}
-
-static inline int pxa168_add_twsi(int id, struct i2c_pxa_platform_data *data,
- struct i2c_board_info *info, unsigned size)
-{
- struct mmp_device_desc *d = NULL;
- int ret;
-
- switch (id) {
- case 0: d = &pxa168_device_twsi0; break;
- case 1: d = &pxa168_device_twsi1; break;
- default:
- return -EINVAL;
- }
-
- ret = i2c_register_board_info(id, info, size);
- if (ret)
- return ret;
-
- return mmp_register_device(d, data, sizeof(*data));
-}
-
-static inline int pxa168_add_pwm(int id)
-{
- struct mmp_device_desc *d = NULL;
-
- switch (id) {
- case 1: d = &pxa168_device_pwm1; break;
- case 2: d = &pxa168_device_pwm2; break;
- case 3: d = &pxa168_device_pwm3; break;
- case 4: d = &pxa168_device_pwm4; break;
- default:
- return -EINVAL;
- }
-
- return mmp_register_device(d, NULL, 0);
-}
-
-static inline int pxa168_add_ssp(int id)
-{
- struct mmp_device_desc *d = NULL;
-
- switch (id) {
- case 1: d = &pxa168_device_ssp1; break;
- case 2: d = &pxa168_device_ssp2; break;
- case 3: d = &pxa168_device_ssp3; break;
- case 4: d = &pxa168_device_ssp4; break;
- case 5: d = &pxa168_device_ssp5; break;
- default:
- return -EINVAL;
- }
- return mmp_register_device(d, NULL, 0);
-}
-
-static inline int pxa168_add_nand(struct pxa3xx_nand_platform_data *info)
-{
- return mmp_register_device(&pxa168_device_nand, info, sizeof(*info));
-}
-
-static inline int pxa168_add_fb(struct pxa168fb_mach_info *mi)
-{
- return mmp_register_device(&pxa168_device_fb, mi, sizeof(*mi));
-}
-
-static inline int pxa168_add_keypad(struct pxa27x_keypad_platform_data *data)
-{
- if (cpu_is_pxa168())
- data->clear_wakeup_event = pxa168_clear_keypad_wakeup;
-
- return mmp_register_device(&pxa168_device_keypad, data, sizeof(*data));
-}
-
-static inline int pxa168_add_eth(struct pxa168_eth_platform_data *data)
-{
- return mmp_register_device(&pxa168_device_eth, data, sizeof(*data));
-}
#endif /* __ASM_MACH_PXA168_H */
diff --git a/arch/arm/mach-mmp/pxa910.c b/arch/arm/mach-mmp/pxa910.c
index b19a069d9fab..f389b99cd9bd 100644
--- a/arch/arm/mach-mmp/pxa910.c
+++ b/arch/arm/mach-mmp/pxa910.c
@@ -17,13 +17,10 @@
#include <asm/hardware/cache-tauros2.h>
#include <asm/mach/time.h>
#include "addr-map.h"
-#include "regs-apbc.h"
#include <linux/soc/mmp/cputype.h>
+#include <linux/soc/pxa/mfp.h>
#include "irqs.h"
-#include "mfp.h"
-#include "devices.h"
#include "pm-pxa910.h"
-#include "pxa910.h"
#include "common.h"
@@ -77,14 +74,6 @@ static struct mfp_addr_map pxa910_mfp_addr_map[] __initdata =
MFP_ADDR_END,
};
-void __init pxa910_init_irq(void)
-{
- icu_init_irq();
-#ifdef CONFIG_PM
- icu_irq_chip.irq_set_wake = pxa910_set_wake;
-#endif
-}
-
static int __init pxa910_init(void)
{
if (cpu_is_pxa910()) {
@@ -102,89 +91,3 @@ static int __init pxa910_init(void)
return 0;
}
postcore_initcall(pxa910_init);
-
-/* system timer - clock enabled, 3.25MHz */
-#define TIMER_CLK_RST (APBC_APBCLK | APBC_FNCLK | APBC_FNCLKSEL(3))
-#define APBC_TIMERS APBC_REG(0x34)
-
-void __init pxa910_timer_init(void)
-{
- /* reset and configure */
- __raw_writel(APBC_APBCLK | APBC_RST, APBC_TIMERS);
- __raw_writel(TIMER_CLK_RST, APBC_TIMERS);
-
- mmp_timer_init(IRQ_PXA910_AP1_TIMER1, 3250000);
-}
-
-/* on-chip devices */
-
-/* NOTE: there are totally 3 UARTs on PXA910:
- *
- * UART1 - Slow UART (can be used both by AP and CP)
- * UART2/3 - Fast UART
- *
- * To be backward compatible with the legacy FFUART/BTUART/STUART sequence,
- * they are re-ordered as:
- *
- * pxa910_device_uart1 - UART2 as FFUART
- * pxa910_device_uart2 - UART3 as BTUART
- *
- * UART1 is not used by AP for the moment.
- */
-PXA910_DEVICE(uart1, "pxa2xx-uart", 0, UART2, 0xd4017000, 0x30, 21, 22);
-PXA910_DEVICE(uart2, "pxa2xx-uart", 1, UART3, 0xd4018000, 0x30, 23, 24);
-PXA910_DEVICE(twsi0, "pxa2xx-i2c", 0, TWSI0, 0xd4011000, 0x28);
-PXA910_DEVICE(twsi1, "pxa2xx-i2c", 1, TWSI1, 0xd4025000, 0x28);
-PXA910_DEVICE(pwm1, "pxa910-pwm", 0, NONE, 0xd401a000, 0x10);
-PXA910_DEVICE(pwm2, "pxa910-pwm", 1, NONE, 0xd401a400, 0x10);
-PXA910_DEVICE(pwm3, "pxa910-pwm", 2, NONE, 0xd401a800, 0x10);
-PXA910_DEVICE(pwm4, "pxa910-pwm", 3, NONE, 0xd401ac00, 0x10);
-PXA910_DEVICE(nand, "pxa3xx-nand", -1, NAND, 0xd4283000, 0x80, 97, 99);
-PXA910_DEVICE(disp, "mmp-disp", 0, LCD, 0xd420b000, 0x1ec);
-PXA910_DEVICE(fb, "mmp-fb", -1, NONE, 0, 0);
-PXA910_DEVICE(panel, "tpo-hvga", -1, NONE, 0, 0);
-
-struct resource pxa910_resource_gpio[] = {
- {
- .start = 0xd4019000,
- .end = 0xd4019fff,
- .flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_PXA910_AP_GPIO,
- .end = IRQ_PXA910_AP_GPIO,
- .name = "gpio_mux",
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device pxa910_device_gpio = {
- .name = "mmp-gpio",
- .id = -1,
- .num_resources = ARRAY_SIZE(pxa910_resource_gpio),
- .resource = pxa910_resource_gpio,
-};
-
-static struct resource pxa910_resource_rtc[] = {
- {
- .start = 0xd4010000,
- .end = 0xd401003f,
- .flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_PXA910_RTC_INT,
- .end = IRQ_PXA910_RTC_INT,
- .name = "rtc 1Hz",
- .flags = IORESOURCE_IRQ,
- }, {
- .start = IRQ_PXA910_RTC_ALARM,
- .end = IRQ_PXA910_RTC_ALARM,
- .name = "rtc alarm",
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device pxa910_device_rtc = {
- .name = "sa1100-rtc",
- .id = -1,
- .num_resources = ARRAY_SIZE(pxa910_resource_rtc),
- .resource = pxa910_resource_rtc,
-};
diff --git a/arch/arm/mach-mmp/pxa910.h b/arch/arm/mach-mmp/pxa910.h
index 7d229214065a..66a691d89ae1 100644
--- a/arch/arm/mach-mmp/pxa910.h
+++ b/arch/arm/mach-mmp/pxa910.h
@@ -6,85 +6,6 @@ extern void pxa910_timer_init(void);
extern void __init pxa910_init_irq(void);
#include <linux/i2c.h>
-#include <linux/platform_data/i2c-pxa.h>
-#include <linux/platform_data/mtd-nand-pxa3xx.h>
-#include <video/mmp_disp.h>
#include <linux/irqchip/mmp.h>
-#include "devices.h"
-
-extern struct mmp_device_desc pxa910_device_uart1;
-extern struct mmp_device_desc pxa910_device_uart2;
-extern struct mmp_device_desc pxa910_device_twsi0;
-extern struct mmp_device_desc pxa910_device_twsi1;
-extern struct mmp_device_desc pxa910_device_pwm1;
-extern struct mmp_device_desc pxa910_device_pwm2;
-extern struct mmp_device_desc pxa910_device_pwm3;
-extern struct mmp_device_desc pxa910_device_pwm4;
-extern struct mmp_device_desc pxa910_device_nand;
-extern struct platform_device pxa168_device_usb_phy;
-extern struct platform_device pxa168_device_u2o;
-extern struct platform_device pxa168_device_u2ootg;
-extern struct platform_device pxa168_device_u2oehci;
-extern struct mmp_device_desc pxa910_device_disp;
-extern struct mmp_device_desc pxa910_device_fb;
-extern struct mmp_device_desc pxa910_device_panel;
-extern struct platform_device pxa910_device_gpio;
-extern struct platform_device pxa910_device_rtc;
-
-static inline int pxa910_add_uart(int id)
-{
- struct mmp_device_desc *d = NULL;
-
- switch (id) {
- case 1: d = &pxa910_device_uart1; break;
- case 2: d = &pxa910_device_uart2; break;
- }
-
- if (d == NULL)
- return -EINVAL;
-
- return mmp_register_device(d, NULL, 0);
-}
-
-static inline int pxa910_add_twsi(int id, struct i2c_pxa_platform_data *data,
- struct i2c_board_info *info, unsigned size)
-{
- struct mmp_device_desc *d = NULL;
- int ret;
-
- switch (id) {
- case 0: d = &pxa910_device_twsi0; break;
- case 1: d = &pxa910_device_twsi1; break;
- default:
- return -EINVAL;
- }
-
- ret = i2c_register_board_info(id, info, size);
- if (ret)
- return ret;
-
- return mmp_register_device(d, data, sizeof(*data));
-}
-
-static inline int pxa910_add_pwm(int id)
-{
- struct mmp_device_desc *d = NULL;
-
- switch (id) {
- case 1: d = &pxa910_device_pwm1; break;
- case 2: d = &pxa910_device_pwm2; break;
- case 3: d = &pxa910_device_pwm3; break;
- case 4: d = &pxa910_device_pwm4; break;
- default:
- return -EINVAL;
- }
-
- return mmp_register_device(d, NULL, 0);
-}
-
-static inline int pxa910_add_nand(struct pxa3xx_nand_platform_data *info)
-{
- return mmp_register_device(&pxa910_device_nand, info, sizeof(*info));
-}
#endif /* __ASM_MACH_PXA910_H */
diff --git a/arch/arm/mach-mmp/regs-apbc.h b/arch/arm/mach-mmp/regs-apbc.h
deleted file mode 100644
index d0d00c2cce38..000000000000
--- a/arch/arm/mach-mmp/regs-apbc.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Application Peripheral Bus Clock Unit
- */
-
-#ifndef __ASM_MACH_REGS_APBC_H
-#define __ASM_MACH_REGS_APBC_H
-
-#include "addr-map.h"
-
-/* Common APB clock register bit definitions */
-#define APBC_APBCLK (1 << 0) /* APB Bus Clock Enable */
-#define APBC_FNCLK (1 << 1) /* Functional Clock Enable */
-#define APBC_RST (1 << 2) /* Reset Generation */
-
-/* Functional Clock Selection Mask */
-#define APBC_FNCLKSEL(x) (((x) & 0xf) << 4)
-
-#endif /* __ASM_MACH_REGS_APBC_H */
diff --git a/arch/arm/mach-mmp/regs-apmu.h b/arch/arm/mach-mmp/regs-apmu.h
deleted file mode 100644
index e36f6503adfb..000000000000
--- a/arch/arm/mach-mmp/regs-apmu.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Application Subsystem Power Management Unit
- */
-
-#ifndef __ASM_MACH_REGS_APMU_H
-#define __ASM_MACH_REGS_APMU_H
-
-#include "addr-map.h"
-
-#define APMU_FNCLK_EN (1 << 4)
-#define APMU_AXICLK_EN (1 << 3)
-#define APMU_FNRST_DIS (1 << 1)
-#define APMU_AXIRST_DIS (1 << 0)
-
-/* Wake Clear Register */
-#define APMU_WAKE_CLR APMU_REG(0x07c)
-
-#define APMU_PXA168_KP_WAKE_CLR (1 << 7)
-#define APMU_PXA168_CFI_WAKE_CLR (1 << 6)
-#define APMU_PXA168_XD_WAKE_CLR (1 << 5)
-#define APMU_PXA168_MSP_WAKE_CLR (1 << 4)
-#define APMU_PXA168_SD4_WAKE_CLR (1 << 3)
-#define APMU_PXA168_SD3_WAKE_CLR (1 << 2)
-#define APMU_PXA168_SD2_WAKE_CLR (1 << 1)
-#define APMU_PXA168_SD1_WAKE_CLR (1 << 0)
-
-#endif /* __ASM_MACH_REGS_APMU_H */
diff --git a/arch/arm/mach-mmp/regs-timers.h b/arch/arm/mach-mmp/regs-timers.h
index a69f4d7e3443..0cc4aca40e2c 100644
--- a/arch/arm/mach-mmp/regs-timers.h
+++ b/arch/arm/mach-mmp/regs-timers.h
@@ -6,11 +6,6 @@
#ifndef __ASM_MACH_REGS_TIMERS_H
#define __ASM_MACH_REGS_TIMERS_H
-#include "addr-map.h"
-
-#define TIMERS1_VIRT_BASE (APB_VIRT_BASE + 0x14000)
-#define TIMERS2_VIRT_BASE (APB_VIRT_BASE + 0x16000)
-
#define TMR_CCR (0x0000)
#define TMR_TN_MM(n, m) (0x0004 + ((n) << 3) + (((n) + (m)) << 2))
#define TMR_CR(n) (0x0028 + ((n) << 2))
diff --git a/arch/arm/mach-mmp/regs-usb.h b/arch/arm/mach-mmp/regs-usb.h
deleted file mode 100644
index ed0d1aa0ad6c..000000000000
--- a/arch/arm/mach-mmp/regs-usb.h
+++ /dev/null
@@ -1,155 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2011 Marvell International Ltd. All rights reserved.
- */
-
-#ifndef __ASM_ARCH_REGS_USB_H
-#define __ASM_ARCH_REGS_USB_H
-
-#define PXA168_U2O_REGBASE (0xd4208000)
-#define PXA168_U2O_PHYBASE (0xd4207000)
-
-#define PXA168_U2H_REGBASE (0xd4209000)
-#define PXA168_U2H_PHYBASE (0xd4206000)
-
-#define MMP3_HSIC1_REGBASE (0xf0001000)
-#define MMP3_HSIC1_PHYBASE (0xf0001800)
-
-#define MMP3_HSIC2_REGBASE (0xf0002000)
-#define MMP3_HSIC2_PHYBASE (0xf0002800)
-
-#define MMP3_FSIC_REGBASE (0xf0003000)
-#define MMP3_FSIC_PHYBASE (0xf0003800)
-
-
-#define USB_REG_RANGE (0x1ff)
-#define USB_PHY_RANGE (0xff)
-
-/* registers */
-#define U2x_CAPREGS_OFFSET 0x100
-
-/* phy regs */
-#define UTMI_REVISION 0x0
-#define UTMI_CTRL 0x4
-#define UTMI_PLL 0x8
-#define UTMI_TX 0xc
-#define UTMI_RX 0x10
-#define UTMI_IVREF 0x14
-#define UTMI_T0 0x18
-#define UTMI_T1 0x1c
-#define UTMI_T2 0x20
-#define UTMI_T3 0x24
-#define UTMI_T4 0x28
-#define UTMI_T5 0x2c
-#define UTMI_RESERVE 0x30
-#define UTMI_USB_INT 0x34
-#define UTMI_DBG_CTL 0x38
-#define UTMI_OTG_ADDON 0x3c
-
-/* For UTMICTRL Register */
-#define UTMI_CTRL_USB_CLK_EN (1 << 31)
-/* pxa168 */
-#define UTMI_CTRL_SUSPEND_SET1 (1 << 30)
-#define UTMI_CTRL_SUSPEND_SET2 (1 << 29)
-#define UTMI_CTRL_RXBUF_PDWN (1 << 24)
-#define UTMI_CTRL_TXBUF_PDWN (1 << 11)
-
-#define UTMI_CTRL_INPKT_DELAY_SHIFT 30
-#define UTMI_CTRL_INPKT_DELAY_SOF_SHIFT 28
-#define UTMI_CTRL_PU_REF_SHIFT 20
-#define UTMI_CTRL_ARC_PULLDN_SHIFT 12
-#define UTMI_CTRL_PLL_PWR_UP_SHIFT 1
-#define UTMI_CTRL_PWR_UP_SHIFT 0
-
-/* For UTMI_PLL Register */
-#define UTMI_PLL_PLLCALI12_SHIFT 29
-#define UTMI_PLL_PLLCALI12_MASK (0x3 << 29)
-
-#define UTMI_PLL_PLLVDD18_SHIFT 27
-#define UTMI_PLL_PLLVDD18_MASK (0x3 << 27)
-
-#define UTMI_PLL_PLLVDD12_SHIFT 25
-#define UTMI_PLL_PLLVDD12_MASK (0x3 << 25)
-
-#define UTMI_PLL_CLK_BLK_EN_SHIFT 24
-#define CLK_BLK_EN (0x1 << 24)
-#define PLL_READY (0x1 << 23)
-#define KVCO_EXT (0x1 << 22)
-#define VCOCAL_START (0x1 << 21)
-
-#define UTMI_PLL_KVCO_SHIFT 15
-#define UTMI_PLL_KVCO_MASK (0x7 << 15)
-
-#define UTMI_PLL_ICP_SHIFT 12
-#define UTMI_PLL_ICP_MASK (0x7 << 12)
-
-#define UTMI_PLL_FBDIV_SHIFT 4
-#define UTMI_PLL_FBDIV_MASK (0xFF << 4)
-
-#define UTMI_PLL_REFDIV_SHIFT 0
-#define UTMI_PLL_REFDIV_MASK (0xF << 0)
-
-/* For UTMI_TX Register */
-#define UTMI_TX_REG_EXT_FS_RCAL_SHIFT 27
-#define UTMI_TX_REG_EXT_FS_RCAL_MASK (0xf << 27)
-
-#define UTMI_TX_REG_EXT_FS_RCAL_EN_SHIFT 26
-#define UTMI_TX_REG_EXT_FS_RCAL_EN_MASK (0x1 << 26)
-
-#define UTMI_TX_TXVDD12_SHIFT 22
-#define UTMI_TX_TXVDD12_MASK (0x3 << 22)
-
-#define UTMI_TX_CK60_PHSEL_SHIFT 17
-#define UTMI_TX_CK60_PHSEL_MASK (0xf << 17)
-
-#define UTMI_TX_IMPCAL_VTH_SHIFT 14
-#define UTMI_TX_IMPCAL_VTH_MASK (0x7 << 14)
-
-#define REG_RCAL_START (0x1 << 12)
-
-#define UTMI_TX_LOW_VDD_EN_SHIFT 11
-
-#define UTMI_TX_AMP_SHIFT 0
-#define UTMI_TX_AMP_MASK (0x7 << 0)
-
-/* For UTMI_RX Register */
-#define UTMI_REG_SQ_LENGTH_SHIFT 15
-#define UTMI_REG_SQ_LENGTH_MASK (0x3 << 15)
-
-#define UTMI_RX_SQ_THRESH_SHIFT 4
-#define UTMI_RX_SQ_THRESH_MASK (0xf << 4)
-
-#define UTMI_OTG_ADDON_OTG_ON (1 << 0)
-
-/* fsic registers */
-#define FSIC_MISC 0x4
-#define FSIC_INT 0x28
-#define FSIC_CTRL 0x30
-
-/* HSIC registers */
-#define HSIC_PAD_CTRL 0x4
-
-#define HSIC_CTRL 0x8
-#define HSIC_CTRL_HSIC_ENABLE (1<<7)
-#define HSIC_CTRL_PLL_BYPASS (1<<4)
-
-#define TEST_GRP_0 0xc
-#define TEST_GRP_1 0x10
-
-#define HSIC_INT 0x14
-#define HSIC_INT_READY_INT_EN (1<<10)
-#define HSIC_INT_CONNECT_INT_EN (1<<9)
-#define HSIC_INT_CORE_INT_EN (1<<8)
-#define HSIC_INT_HS_READY (1<<2)
-#define HSIC_INT_CONNECT (1<<1)
-#define HSIC_INT_CORE (1<<0)
-
-#define HSIC_CONFIG 0x18
-#define USBHSIC_CTRL 0x20
-
-#define HSIC_USB_CTRL 0x28
-#define HSIC_USB_CTRL_CLKEN 1
-#define HSIC_USB_CLK_PHY 0x0
-#define HSIC_USB_CLK_PMU 0x1
-
-#endif /* __ASM_ARCH_PXA_U2O_H */
diff --git a/arch/arm/mach-mmp/time.c b/arch/arm/mach-mmp/time.c
index 41b2e8abc9e6..0f0ed2428595 100644
--- a/arch/arm/mach-mmp/time.c
+++ b/arch/arm/mach-mmp/time.c
@@ -29,18 +29,13 @@
#include <linux/sched_clock.h>
#include <asm/mach/time.h>
-#include "addr-map.h"
#include "regs-timers.h"
-#include "regs-apbc.h"
-#include "irqs.h"
#include <linux/soc/mmp/cputype.h>
-#define TIMERS_VIRT_BASE TIMERS1_VIRT_BASE
-
#define MAX_DELTA (0xfffffffe)
#define MIN_DELTA (16)
-static void __iomem *mmp_timer_base = TIMERS_VIRT_BASE;
+static void __iomem *mmp_timer_base;
/*
* FIXME: the timer needs some delay to stablize the counter capture
@@ -174,7 +169,7 @@ static void __init timer_config(void)
__raw_writel(0x2, mmp_timer_base + TMR_CER);
}
-void __init mmp_timer_init(int irq, unsigned long rate)
+static void __init mmp_timer_init(int irq, unsigned long rate)
{
timer_config();
--
2.29.2
More information about the linux-arm-kernel
mailing list