[PATCH net-next 1/2] net:xilinx_axi: set mdio frequency according to DT
Alexander Stein
alexander.stein at ew.tq-group.com
Thu Oct 20 04:35:06 PDT 2022
Hi,
Am Donnerstag, 20. Oktober 2022, 11:41:05 CEST schrieb Andy Chiu:
> Some FPGA platforms has 80KHz MDIO bus frequency constraint when
> conecting Ethernet to its on-board external Marvell PHY. Thus, we may
> have to set MDIO clock according to the DT. Otherwise, use the default
> 2.5 MHz, as specified by 802.3, if the entry is not present.
>
> Signed-off-by: Andy Chiu <andy.chiu at sifive.com>
> Reviewed-by: Greentime Hu <greentime.hu at sifive.com>
> ---
> .../net/ethernet/xilinx/xilinx_axienet_mdio.c | 25 ++++++++++++++++---
> 1 file changed, 21 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_mdio.c
> b/drivers/net/ethernet/xilinx/xilinx_axienet_mdio.c index
> 0b3b6935c558..d07c39d3bcf0 100644
> --- a/drivers/net/ethernet/xilinx/xilinx_axienet_mdio.c
> +++ b/drivers/net/ethernet/xilinx/xilinx_axienet_mdio.c
> @@ -18,6 +18,7 @@
> #include "xilinx_axienet.h"
>
> #define MAX_MDIO_FREQ 2500000 /* 2.5 MHz */
> +#define MDIO_CLK_DIV_MASK 0x3f /* bits[5:0] */
> #define DEFAULT_HOST_CLOCK 150000000 /* 150 MHz */
>
> /* Wait till MDIO interface is ready to accept a new transaction.*/
> @@ -155,7 +156,9 @@ static int axienet_mdio_write(struct mii_bus *bus, int
> phy_id, int reg, **/
> int axienet_mdio_enable(struct axienet_local *lp)
> {
> + u32 clk_div;
> u32 host_clock;
> + u32 mdio_freq;
>
> lp->mii_clk_div = 0;
>
> @@ -184,6 +187,13 @@ int axienet_mdio_enable(struct axienet_local *lp)
> host_clock);
> }
>
> + if (of_property_read_u32(lp->dev->of_node, "xlnx,mdio-freq",
> + &mdio_freq)) {
> + mdio_freq = MAX_MDIO_FREQ;
> + netdev_info(lp->ndev, "Setting default mdio clock to
%u\n",
> + mdio_freq);
I would opt to print this message only if using non-default frequency.
Best regards,
Alexander
> + }
> +
> /* clk_div can be calculated by deriving it from the equation:
> * fMDIO = fHOST / ((1 + clk_div) * 2)
> *
> @@ -209,13 +219,20 @@ int axienet_mdio_enable(struct axienet_local *lp)
> * "clock-frequency" from the CPU
> */
>
> - lp->mii_clk_div = (host_clock / (MAX_MDIO_FREQ * 2)) - 1;
> + clk_div = (host_clock / (mdio_freq * 2)) - 1;
> /* If there is any remainder from the division of
> - * fHOST / (MAX_MDIO_FREQ * 2), then we need to add
> + * fHOST / (mdio_freq * 2), then we need to add
> * 1 to the clock divisor or we will surely be above 2.5 MHz
> */
> - if (host_clock % (MAX_MDIO_FREQ * 2))
> - lp->mii_clk_div++;
> + if (host_clock % (mdio_freq * 2))
> + clk_div++;
> +
> + /* Check for overflow of mii_clk_div */
> + if (clk_div & ~MDIO_CLK_DIV_MASK) {
> + netdev_dbg(lp->ndev, "MDIO clock divisor overflow,
setting to maximum
> value\n"); + clk_div = MDIO_CLK_DIV_MASK;
> + }
> + lp->mii_clk_div = (u8)clk_div;
>
> netdev_dbg(lp->ndev,
> "Setting MDIO clock divisor to %u/%u Hz host clock.
\n",
More information about the linux-arm-kernel
mailing list