[PATCH v2] arm64: dts: mt8195: Add Ethernet controller

[AngeloGioacchino Del Regno]

Il 19/10/22 11:15, Biao Huang ha scritto:
> Add Ethernet controller node for mt8195.
> 
> Signed-off-by: Biao Huang <biao.huang at mediatek.com>
> ---
>   arch/arm64/boot/dts/mediatek/mt8195-demo.dts | 88 ++++++++++++++++++++
>   arch/arm64/boot/dts/mediatek/mt8195.dtsi     | 86 +++++++++++++++++++
>   2 files changed, 174 insertions(+)
> 

..snip..

> diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> index 905d1a90b406..7f7d9f8e72ee 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> @@ -1042,6 +1042,92 @@ spis1: spi at 1101e000 {
>   			status = "disabled";
>   		};
>   
> +		stmmac_axi_setup: stmmac-axi-config {

Didn't you get a warning during dtb build for these ones?
And if you did, why have you ignored it? :-)

> +			snps,wr_osr_lmt = <0x7>;
> +			snps,rd_osr_lmt = <0x7>;
> +			snps,blen = <0 0 0 0 16 8 4>;
> +		};
> +

..snip..

> +
> +		eth: ethernet at 11021000 {
> +			compatible = "mediatek,mt8195-gmac", "snps,dwmac-5.10a";
> +			reg = <0 0x11021000 0 0x4000>;
> +			interrupts = <GIC_SPI 716 IRQ_TYPE_LEVEL_HIGH 0>;
> +			interrupt-names = "macirq";
> +			clock-names = "axi",
> +				      "apb",
> +				      "mac_cg",
> +				      "mac_main",
> +				      "ptp_ref",
> +				      "rmii_internal";
> +			clocks = <&pericfg_ao CLK_PERI_AO_ETHERNET>,
> +				 <&pericfg_ao CLK_PERI_AO_ETHERNET_BUS>,
> +				 <&pericfg_ao CLK_PERI_AO_ETHERNET_MAC>,
> +				 <&topckgen CLK_TOP_SNPS_ETH_250M>,
> +				 <&topckgen CLK_TOP_SNPS_ETH_62P4M_PTP>,
> +				 <&topckgen CLK_TOP_SNPS_ETH_50M_RMII>;
> +			assigned-clocks = <&topckgen CLK_TOP_SNPS_ETH_250M>,
> +					  <&topckgen CLK_TOP_SNPS_ETH_62P4M_PTP>,
> +					  <&topckgen CLK_TOP_SNPS_ETH_50M_RMII>;
> +			assigned-clock-parents = <&topckgen CLK_TOP_ETHPLL_D2>,
> +						 <&topckgen CLK_TOP_ETHPLL_D8>,
> +						 <&topckgen CLK_TOP_ETHPLL_D10>;
> +			power-domains = <&spm MT8195_POWER_DOMAIN_ETHER>;
> +			mediatek,pericfg = <&infracfg_ao>;
> +			snps,axi-config = <&stmmac_axi_setup>;
> +			snps,mtl-rx-config = <&mtl_rx_setup>;
> +			snps,mtl-tx-config = <&mtl_tx_setup>;
> +			snps,txpbl = <16>;
> +			snps,rxpbl = <16>;
> +			snps,clk-csr = <0>;
> +			status = "disabled";

Please move stmmac-axi-config, rx-queues-config, tx-queues-config here as a subnode
or in the root node, respecting address/size cells being zero.
Of course adding that here means also specifying {address,size}-cells = <0> in this
ethernet node.

Regards,
Angelo