[PATCH 2/3] arm64: dts: ti: Add initial support for AM68 SK System on Module

[Krzysztof Kozlowski]

On 18/10/2022 08:38, Sinthu Raja wrote:
> From: Sinthu Raja <sinthu.raja at ti.com>
> 
> AM68 Starter Kit (SK)[1] is a low cost, small form factor board designed
> for TI’s AM68 SoC. TI’s AM68 SoC comprises of dual core A72, high
> performance vision accelerators, hardware accelerators, latest C71x
> DSP, high bandwidth real-time IPs for capture and display. The SoC is
> power optimized to provide best in class performance for industrial
> applications.
> 
>  AM68 SK supports the following interfaces:
>       * 16 GB LPDDR4 RAM
>       * x1 Gigabit Ethernet interface
>       * x1 USB 3.1 Type-C port
>       * x2 USB 3.1 Type-A ports
>       * x1 PCIe M.2 M Key
>       * 512 Mbit OSPI flash
>       * x2 CSI2 Camera interface (RPi and TI Camera connector)
>       * 40-pin Raspberry Pi GPIO header
> 
> SK's System on Module (SoM) contains the SoC and DDR.
> Therefore, add DT node for the SOC and DDR on the SoM.
> 
> Schematics: https://www.ti.com/lit/zip/SPRR463
> TRM: http://www.ti.com/lit/pdf/spruj28
> 
> Signed-off-by: Sinthu Raja <sinthu.raja at ti.com>
> ---
>  arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi | 129 +++++++++++++++++++++
>  1 file changed, 129 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
> new file mode 100644
> index 000000000000..734c13eb0490
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
> @@ -0,0 +1,129 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
> + */
> +
> +/dts-v1/;
> +
> +#include "k3-j721s2.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> +	memory at 80000000 {
> +		device_type = "memory";
> +		/* 16 GB RAM */
> +		reg = <0x00 0x80000000 0x00 0x80000000>,
> +		      <0x08 0x80000000 0x03 0x80000000>;
> +	};
> +
> +	/* Reserving memory regions still pending */
> +	reserved_memory: reserved-memory {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		secure_ddr: optee at 9e800000 {
> +			reg = <0x00 0x9e800000 0x00 0x01800000>;
> +			alignment = <0x1000>;
> +			no-map;
> +		};
> +

Drop empty line.


Best regards,
Krzysztof