[PATCH v4 5/8] ARM: dts: stm32: add adc support to stm32mp13

[Fabrice Gasnier]

On 10/12/22 16:22, Olivier Moysan wrote:
> Add ADC1 and ADC2 support to STM32MP13 SoC family.
> 
> The STM32MP131 provides only ADC2, while other STM32MP13 SoCs provide
> both ADC1 and ADC2.
> 
> Internal channels support limitations:
> - VREFINT internal channel requires calibration data from OTP memory.
>   The nvmem properties used to access OTP are not defined for time being,
>   as OTP support is not yet enabled.
> 
> - VBAT internal channel is not defined by default in SoC DT, and
>   has be defined in board DT when needed, instead. This avoids unwanted
>   current consumption on battery, when ADC conversions are performed
>   on any other channels.
> 
> Signed-off-by: Olivier Moysan <olivier.moysan at foss.st.com>
> ---
>  arch/arm/boot/dts/stm32mp131.dtsi | 43 +++++++++++++++++++++++++++++++
>  arch/arm/boot/dts/stm32mp133.dtsi | 31 ++++++++++++++++++++++
>  2 files changed, 74 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/stm32mp131.dtsi b/arch/arm/boot/dts/stm32mp131.dtsi
> index dd35a607073d..0b85e7744db5 100644
> --- a/arch/arm/boot/dts/stm32mp131.dtsi
> +++ b/arch/arm/boot/dts/stm32mp131.dtsi
> @@ -313,6 +313,49 @@ i2c5: i2c at 4c006000 {
>  			status = "disabled";
>  		};
>  
> +		adc_2: adc at 48004000 {

Hi Olivier,

Nodes should be sorted by address here. Maybe Alexandre will take care
when applying ?

With that fixed, you can add my:

Reviewed-by: Fabrice Gasnier <fabrice.gasnier at foss.st.com>

Thanks,
Fabrice

> +			compatible = "st,stm32mp13-adc-core";
> +			reg = <0x48004000 0x400>;
> +			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&rcc ADC2>, <&rcc ADC2_K>;
> +			clock-names = "bus", "adc";
> +			interrupt-controller;
> +			#interrupt-cells = <1>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +
> +			adc2: adc at 0 {
> +				compatible = "st,stm32mp13-adc";
> +				#io-channel-cells = <1>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				reg = <0x0>;
> +				interrupt-parent = <&adc_2>;
> +				interrupts = <0>;
> +				dmas = <&dmamux1 10 0x400 0x80000001>;
> +				dma-names = "rx";
> +				status = "disabled";
> +
> +				channel at 13 {
> +					reg = <13>;
> +					label = "vrefint";
> +				};
> +				channel at 14 {
> +					reg = <14>;
> +					label = "vddcore";
> +				};
> +				channel at 16 {
> +					reg = <16>;
> +					label = "vddcpu";
> +				};
> +				channel at 17 {
> +					reg = <17>;
> +					label = "vddq_ddr";
> +				};
> +			};
> +		};
> +
>  		rcc: rcc at 50000000 {
>  			compatible = "st,stm32mp13-rcc", "syscon";
>  			reg = <0x50000000 0x1000>;
> diff --git a/arch/arm/boot/dts/stm32mp133.dtsi b/arch/arm/boot/dts/stm32mp133.dtsi
> index 531c263c9f46..df451c3c2a26 100644
> --- a/arch/arm/boot/dts/stm32mp133.dtsi
> +++ b/arch/arm/boot/dts/stm32mp133.dtsi
> @@ -33,5 +33,36 @@ m_can2: can at 4400f000 {
>  			bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>;
>  			status = "disabled";
>  		};
> +
> +		adc_1: adc at 48003000 {
> +			compatible = "st,stm32mp13-adc-core";
> +			reg = <0x48003000 0x400>;
> +			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&rcc ADC1>, <&rcc ADC1_K>;
> +			clock-names = "bus", "adc";
> +			interrupt-controller;
> +			#interrupt-cells = <1>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +
> +			adc1: adc at 0 {
> +				compatible = "st,stm32mp13-adc";
> +				#io-channel-cells = <1>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				reg = <0x0>;
> +				interrupt-parent = <&adc_1>;
> +				interrupts = <0>;
> +				dmas = <&dmamux1 9 0x400 0x80000001>;
> +				dma-names = "rx";
> +				status = "disabled";
> +
> +				channel at 18 {
> +					reg = <18>;
> +					label = "vrefint";
> +				};
> +			};
> +		};
>  	};
>  };