[PATCH v9, 2/4] mailbox: mtk-cmdq: add gce software ddr enable private data

[yongqiang.niu]

On Thu, 2022-10-06 at 11:29 +0200, AngeloGioacchino Del Regno wrote:
> Il 06/10/22 06:34, Yongqiang Niu ha scritto:
> > if gce work control by software, we need set software enable
> > for MT8186 Soc
> > 
> > there is a handshake flow between gce and ddr hardware,
> > if not set ddr enable flag of gce, ddr will fall into idle
> > mode, then gce instructions will not process done.
> > we need set this flag of gce to tell ddr when gce is idle or busy
> > controlled by software flow.
> > 
> > 0x48[2:0] means control by software
> > 0x48[18:16] means ddr enable
> > 0x48[2:0] is pre-condition of 0x48[18:16].
> > if we want set 0x48[18:16] ddr enable, 0x48[2:0] must be set at
> > same
> > time.
> > and only these bits is useful, other bits is useless bits
> > 
> > Signed-off-by: Yongqiang Niu <yongqiang.niu at mediatek.com>
> > ---
> >   drivers/mailbox/mtk-cmdq-mailbox.c | 7 +++++++
> >   1 file changed, 7 insertions(+)
> > 
> > diff --git a/drivers/mailbox/mtk-cmdq-mailbox.c
> > b/drivers/mailbox/mtk-cmdq-mailbox.c
> > index c3cb24f51699..04eb44d89119 100644
> > --- a/drivers/mailbox/mtk-cmdq-mailbox.c
> > +++ b/drivers/mailbox/mtk-cmdq-mailbox.c
> > @@ -39,6 +39,7 @@
> >   
> >   #define GCE_GCTL_VALUE			0x48
> >   #define GCE_CTRL_BY_SW				GENMASK(2, 0)
> > +#define GCE_DDR_EN				GENMASK(18, 16)
> >   
> >   #define CMDQ_THR_ACTIVE_SLOT_CYCLES	0x3200
> >   #define CMDQ_THR_ENABLED		0x1
> > @@ -81,6 +82,7 @@ struct cmdq {
> >   	bool			suspended;
> >   	u8			shift_pa;
> >   	bool			control_by_sw;
> > +	bool			sw_ddr_en;
> >   	u32			gce_num;
> >   };
> >   
> > @@ -88,6 +90,7 @@ struct gce_plat {
> >   	u32 thread_nr;
> >   	u8 shift;
> >   	bool control_by_sw;
> > +	bool sw_ddr_en;
> >   	u32 gce_num;
> >   };
> >   
> > @@ -132,6 +135,9 @@ static void cmdq_init(struct cmdq *cmdq)
> >   	if (cmdq->control_by_sw)
> >   		writel(GCE_CTRL_BY_SW, cmdq->base + GCE_GCTL_VALUE);
> >   
> > +	if (cmdq->sw_ddr_en)
> > +		writel(GCE_DDR_EN | GCE_CTRL_BY_SW, cmdq->base +
> > GCE_GCTL_VALUE);
> > +
> 
> No. That's redundant.
> Here's a better way:
> 
> 	u32 gctl_regval = 0;
> 
> 	if (cmdq->control_by_sw)
> 		gctl_regval = GCE_CTRL_BY_SW;
> 	if (cmdq->sw_ddr_en)
> 		gctl_regval |= GCE_DDR_EN;
> 
> 	if (val)
> 		writel(gctl_regval, cmdq->base + GCE_GCTL_VALUE);
> 
> Regards,
> Angelo

thanks very much for your advise.
shall i separate this into two patches? 
1st one is 
	u32 gctl_regval = 0;
	if (cmdq->control_by_sw)
> 		gctl_regval = GCE_CTRL_BY_SW;
> 	if (val)
> 		writel(gctl_regval, cmdq->base + GCE_GCTL_VALUE);



2nd just add this
	if (cmdq->sw_ddr_en)
> 		gctl_regval |= GCE_DDR_EN;

or one patch is ok?

> 
> >   	writel(CMDQ_THR_ACTIVE_SLOT_CYCLES, cmdq->base +
> > CMDQ_THR_SLOT_CYCLES);
> >   	for (i = 0; i <= CMDQ_MAX_EVENT; i++)
> >   		writel(i, cmdq->base + CMDQ_SYNC_TOKEN_UPDATE);
> > @@ -545,6 +551,7 @@ static int cmdq_probe(struct platform_device
> > *pdev)
> >   	cmdq->thread_nr = plat_data->thread_nr;
> >   	cmdq->shift_pa = plat_data->shift;
> >   	cmdq->control_by_sw = plat_data->control_by_sw;
> > +	cmdq->sw_ddr_en = plat_data->sw_ddr_en;
> >   	cmdq->gce_num = plat_data->gce_num;
> >   	cmdq->irq_mask = GENMASK(cmdq->thread_nr - 1, 0);
> >   	err = devm_request_irq(dev, cmdq->irq, cmdq_irq_handler,
> > IRQF_SHARED,
> 
> 
>