[PATCH 3/3] arm64: dts: Add device tree for the Debix Model A Board

[Krzysztof Kozlowski]

On 03/10/2022 14:06, Laurent Pinchart wrote:
> On Mon, Oct 03, 2022 at 11:26:54AM +0200, Krzysztof Kozlowski wrote:
>> On 03/10/2022 10:37, Daniel Scally wrote:
>>> Add a device tree file describing the Debix Model A board from
>>> Polyhex Technology Co.
>>>
>>> Signed-off-by: Daniel Scally <dan.scally at ideasonboard.com>
>>> ---
>>>  arch/arm64/boot/dts/freescale/Makefile        |   1 +
>>>  .../dts/freescale/imx8mp-debix-model-a.dts    | 550 ++++++++++++++++++
>>>  2 files changed, 551 insertions(+)
>>>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts
>>>
>>> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
>>> index 238a83e5b8c6..f26e802cef82 100644
>>> --- a/arch/arm64/boot/dts/freescale/Makefile
>>> +++ b/arch/arm64/boot/dts/freescale/Makefile
>>> @@ -79,6 +79,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
>>>  dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx.dtb
>>>  dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
>>>  dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
>>> +dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb
>>>  dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
>>>  dtb-$(CONFIG_ARCH_MXC) += imx8mp-icore-mx8mp-edimm2.2.dtb
>>>  dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
>>> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts b/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts
>>> new file mode 100644
>>> index 000000000000..6d0fa3930d0b
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts
>>> @@ -0,0 +1,550 @@
>>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>>> +/*
>>> + * Copyright 2019 NXP
>>> + */
>>> +
>>> +/dts-v1/;
>>> +
>>> +#include <dt-bindings/gpio/gpio.h>
>>> +#include <dt-bindings/leds/common.h>
>>> +#include <dt-bindings/usb/pd.h>
>>> +
>>> +#include "imx8mp.dtsi"
>>> +
>>> +/ {
>>> +	model = "Polyhex Debix Model A (2GB) i.MX8MPlus board";
>>> +	compatible = "polyhex,imx8mp-debix-modela2gb", "fsl,imx8mp";
>>> +
>>> +	chosen {
>>> +		stdout-path = &uart2;
>>> +	};
>>> +
>>> +	gpio-leds {
>>> +		compatible = "gpio-leds";
>>> +		pinctrl-names = "default";
>>> +		pinctrl-0 = <&pinctrl_gpio_led>;
>>> +
>>> +		status-led {
>>> +			function = LED_FUNCTION_POWER;
>>> +			color = <LED_COLOR_ID_RED>;
>>> +			gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
>>> +			default-state = "on";
>>> +		};
>>> +	};
>>> +
>>> +	reg_usdhc2_vmmc: regulator-usdhc2 {
>>> +		compatible = "regulator-fixed";
>>> +		pinctrl-names = "default";
>>> +		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
>>> +		regulator-name = "VSD_3V3";
>>> +		regulator-min-microvolt = <3300000>;
>>> +		regulator-max-microvolt = <3300000>;
>>> +		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
>>> +		enable-active-high;
>>> +	};
>>> +};
>>> +
>>> +&A53_0 {
>>> +	cpu-supply = <&buck2>;
>>> +};
>>> +
>>> +&A53_1 {
>>> +	cpu-supply = <&buck2>;
>>> +};
>>> +
>>> +&A53_2 {
>>> +	cpu-supply = <&buck2>;
>>> +};
>>> +
>>> +&A53_3 {
>>> +	cpu-supply = <&buck2>;
>>> +};
>>> +
>>> +&eqos {
>>> +	pinctrl-names = "default";
>>> +	pinctrl-0 = <&pinctrl_eqos>;
>>> +	phy-connection-type = "rgmii-id";
>>> +	phy-handle = <&ethphy0>;
>>> +	status = "okay";
>>> +
>>> +	mdio {
>>> +		compatible = "snps,dwmac-mdio";
>>> +		#address-cells = <1>;
>>> +		#size-cells = <0>;
>>> +
>>> +		ethphy0: ethernet-phy at 0 {
>>> +			compatible = "ethernet-phy-ieee802.3-c22";
>>> +			reg = <0>;
>>> +			reset-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
>>> +			reset-assert-us = <20>;
>>> +			reset-deassert-us = <200000>;
>>> +		};
>>> +	};
>>> +};
>>> +
>>> +&fec {
>>> +	pinctrl-names = "default";
>>> +	pinctrl-0 = <&pinctrl_fec>;
>>> +	phy-connection-type = "rgmii-id";
>>> +	phy-handle = <&ethphy1>;
>>> +	fsl,magic-packet;
>>> +	status = "okay";
>>> +
>>> +	mdio {
>>> +		#address-cells = <1>;
>>> +		#size-cells = <0>;
>>> +
>>> +		ethphy1: ethernet-phy at 0 {
>>> +			compatible = "ethernet-phy-ieee802.3-c22";
>>> +			reg = <0>;
>>> +			reset-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
>>> +			reset-assert-us = <10>;
>>> +			reset-deassert-us = <150>;
>>> +		};
>>> +	};
>>> +};
>>> +
>>> +&i2c1 {
>>> +	clock-frequency = <400000>;
>>> +	pinctrl-names = "default";
>>> +	pinctrl-0 = <&pinctrl_i2c1>;
>>> +	status = "okay";
>>> +
>>> +	pmic at 25 {
>>> +		reg = <0x25>;
>>> +		compatible = "nxp,pca9450c";
>>> +		pinctrl-names = "default";
>>> +		pinctrl-0 = <&pinctrl_pmic>;
>>> +		interrupt-parent = <&gpio1>;
>>> +		interrupts = <3 GPIO_ACTIVE_LOW>;
>>
>> Nope, wrong flag. This is a hint for us that you based your DTS on
>> something ancient (e.g. broken downstream stuff). Please start from
>> *scratch* and write your DTS based on a board taken from mainline.
>>
>> There is no point for us to repeat review for all the things  we already
>> fixed in mainline.
> 
> We can't fully do that, as we don't have access to the schematics for
> the board. What we can do, however, is to compare this .dts to others
> from mainline and investigate all differences to see if they can be
> bugs.

The upstreaming process is rather to take a DTS from the mainline and
customize it. Add stuff, remove something, change other nodes. Several
pieces are similar between boards, like the PMIC. I think this patch was
done in other way - entire PMIC was taken from downstream - therefore I
recommend the previous approach. It does not mean that everything should
be done from 0 but rather based on mainline DTS to avoid the same
mistakes we already fixed. Many times...

Best regards,
Krzysztof