[PATCH 7/8] dt-bindings: soc: socionext: Add UniPhier DWC3 USB glue layer

[Rob Herring]

On Tue, 29 Nov 2022 19:35:08 +0900, Kunihiko Hayashi wrote:
> Add DT binding schema for components belonging to the platform-specific
> DWC3 USB glue layer implemented in UniPhier SoCs.
> 
> This USB glue layer works as a sideband logic for the host controller,
> including core reset, vbus control, PHYs, and some signals to the
> controller.
> 
> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko at socionext.com>
> ---
>  .../socionext,uniphier-dwc3-glue.yaml         | 106 ++++++++++++++++++
>  1 file changed, 106 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/soc/socionext/socionext,uniphier-dwc3-glue.yaml
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/phy/socionext,uniphier-usb3ss-phy.example.dtb: usb-glue at 65b00000: 'reg' is a required property
	From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/soc/socionext/socionext,uniphier-dwc3-glue.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/phy/socionext,uniphier-usb3ss-phy.example.dtb: usb-glue at 65b00000: 'ss-phy at 300' does not match any of the regexes: '^phy@[0-9a-f]+$', '^regulator@[0-9a-f]+$', '^reset-controller@[0-9a-f]+$', 'pinctrl-[0-9]+'
	From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/soc/socionext/socionext,uniphier-dwc3-glue.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/phy/socionext,uniphier-usb3hs-phy.example.dtb: usb-glue at 65b00000: 'reg' is a required property
	From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/soc/socionext/socionext,uniphier-dwc3-glue.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/phy/socionext,uniphier-usb3hs-phy.example.dtb: usb-glue at 65b00000: 'hs-phy at 200' does not match any of the regexes: '^phy@[0-9a-f]+$', '^regulator@[0-9a-f]+$', '^reset-controller@[0-9a-f]+$', 'pinctrl-[0-9]+'
	From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/soc/socionext/socionext,uniphier-dwc3-glue.yaml

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20221129103509.9958-8-hayashi.kunihiko@socionext.com

This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command.