[PATCH RFC v2 5/7] arm64: dts: imx: fix touchscreen reset GPIO polarity

[Quentin Schulz]

Hi David,

Thanks Fabio for the Cc.

On 11/22/22 08:18, David Jander wrote:
> On Mon, 21 Nov 2022 15:18:32 -0300
> Fabio Estevam <festevam at gmail.com> wrote:
> 
>> [Adding Angus and David]
> 
> Thanks. This was apparently necessary ;-)
> 
>> On Mon, Nov 21, 2022 at 3:12 PM Quentin Schulz <foss+kernel at 0leil.net> wrote:
>>>
>>> From: Quentin Schulz <quentin.schulz at theobroma-systems.com>
>>>
>>> The reset line is active low for the Goodix touchscreen controller so
>>> let's fix the polarity in the Device Tree node.
>>>
>>> Signed-off-by: Quentin Schulz <quentin.schulz at theobroma-systems.com>
>>> ---
>>>   arch/arm64/boot/dts/freescale/imx8mm-prt8mm.dts         | 2 +-
>>>   arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts | 2 +-
>>>   2 files changed, 2 insertions(+), 2 deletions(-)
>>>
>>> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-prt8mm.dts b/arch/arm64/boot/dts/freescale/imx8mm-prt8mm.dts
>>> index 9fbbbb556c0b3..df7e5ae9698e1 100644
>>> --- a/arch/arm64/boot/dts/freescale/imx8mm-prt8mm.dts
>>> +++ b/arch/arm64/boot/dts/freescale/imx8mm-prt8mm.dts
>>> @@ -107,7 +107,7 @@ touchscreeen at 5d {
>>>                  interrupt-parent = <&gpio1>;
>>>                  interrupts = <8 IRQ_TYPE_NONE>;
>>>                  irq-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
>>> -               reset-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
>>> +               reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
> 
> NACK!
> 
> The PRT8MM has an inverter in the reset line. The reason for that is that the
> reset line needs to be inactive when the driving side is unpowered.
> The DT was correct, this change will break it.
> 

The DT was correct. The implementation in the driver is changed (the 
polarity is swapped) in this patch series, therefore the DT isn't 
correct anymore, hence this patch.

See 
https://lore.kernel.org/linux-input/20221103-upstream-goodix-reset-v2-0-2c38fb03a300@theobroma-systems.com/ 
for the whole patch series.

This DT patch alone is obviously incorrect, but the context around it 
matters. I could/should have made it all into one big patch, the 
question is then how this big tree-crossing patch would be merged into 
Linux (if there's consensus). We're not there yet.

For some additional background on the discussion that was had in the v1:
https://lore.kernel.org/all/267de96a-0129-a97d-9bf6-e1001b422a1a@theobroma-systems.com/
I messed up the Cc list in the v1, apologies for the missing context in 
the archived mails, I think one should be able to understand the 
important bits by reading the answers in-mail. There, Dmitry, Hans and I 
discussed the meaning of the active level of GPIOs/reset lines and I 
expressed the reasons for such a change (which are also listed in the 
cover letter of this patch series).

As stated in v1 cover letter, no implementation will satisfy every one. 
We either make the DT binding implementation specific (which is what it 
shouldn't be), or we swap the polarity in the Linux implementation and 
thus the DT but then break DT backward compatibility.

Cheers,
Quentin