[PATCH v3 4/4] arm64: dts: ti: Add support for J784S4 EVM board
Andrew Davis
afd at ti.com
Fri Nov 18 09:40:19 PST 2022
On 11/16/22 7:04 AM, Apurva Nandan wrote:
> J784S4 EVM board is designed for TI J784S4 SoC. It supports the following
> interfaces:
> * 32 GB DDR4 RAM
> * x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
> * x1 Input Audio Jack, x1 Output Audio Jack
> * x1 USB2.0 Hub with two Type A host and x1 USB 3.1 Type-C Port
> * x2 4L PCIe connector
> * x1 UHS-1 capable micro-SD card slot
> * 512 Mbit OSPI flash, 1 Gbit Octal NAND flash, 512 Mbit QSPI flash,
> UFS flash.
> * x6 UART through UART-USB bridge
> * XDS110 for onboard JTAG debug using USB
> * Temperature sensors, user push buttons and LEDs
> * 40-pin User Expansion Connector
> * x2 ENET Expansion Connector, x1 GESI expander, x2 Display connector
> * x1 15-pin CSI header
> * x6 MCAN instances
>
> Add basic support for J784S4-EVM.
>
> Schematics: https://www.ti.com/lit/zip/sprr458
>
> Signed-off-by: Hari Nagalla <hnagalla at ti.com>
> Signed-off-by: Nishanth Menon <nm at ti.com>
> Signed-off-by: Apurva Nandan <a-nandan at ti.com>
> ---
> arch/arm64/boot/dts/ti/Makefile | 2 +
> arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 197 +++++++++++++++++++++++
> 2 files changed, 199 insertions(+)
> create mode 100644 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
>
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index 4555a5be2257..67621b349e88 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -19,6 +19,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
>
> dtb-$(CONFIG_ARCH_K3) += k3-j721s2-common-proc-board.dtb
>
> +dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
> +
> dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> new file mode 100644
> index 000000000000..53516fb2b346
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> @@ -0,0 +1,196 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
> + *
> + * EVM Board Schematics: https://www.ti.com/lit/zip/sprr458
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/net/ti-dp83867.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include "k3-j784s4.dtsi"
> +
> +/ {
> + compatible = "ti,j784s4-evm", "ti,j784s4";
> + model = "Texas Instruments J784S4 EVM";
> +
> + chosen {
> + stdout-path = "serial2:115200n8";
> + };
> +
> + aliases {
> + serial2 = &main_uart8;
This feels hacky. Your chosen node picks serial2 as that is usually
the one that is wired up on K3 boards. But on this board it is main_uart8.
So why not have this be serial10, then choose
stdout-path = "serial10:115200n8";
Also, I've made comments on previous version of this series, it is
nice to include folks who have commented before in the CC for future
versions, that way our filters don't hide these away and we can more
easily check that our comments have been addressed.
Andrew
> + mmc1 = &main_sdhci1;
> + i2c0 = &main_i2c0;
> + };
> +
> + memory at 80000000 {
> + device_type = "memory";
> + /* 32G RAM */
> + reg = <0x00 0x80000000 0x00 0x80000000>,
> + <0x08 0x80000000 0x07 0x80000000>;
> + };
> +
> + reserved_memory: reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + secure_ddr: optee at 9e800000 {
> + reg = <0x00 0x9e800000 0x00 0x01800000>;
> + no-map;
> + };
> + };
> +
> + evm_12v0: regulator-evm12v0 {
> + /* main supply */
> + compatible = "regulator-fixed";
> + regulator-name = "evm_12v0";
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vsys_3v3: regulator-vsys3v3 {
> + /* Output of LM5140 */
> + compatible = "regulator-fixed";
> + regulator-name = "vsys_3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&evm_12v0>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vsys_5v0: regulator-vsys5v0 {
> + /* Output of LM5140 */
> + compatible = "regulator-fixed";
> + regulator-name = "vsys_5v0";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&evm_12v0>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vdd_mmc1: regulator-sd {
> + /* Output of TPS22918 */
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_mmc1";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + enable-active-high;
> + vin-supply = <&vsys_3v3>;
> + gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
> + };
> +
> + vdd_sd_dv: regulator-TLV71033 {
> + /* Output of TLV71033 */
> + compatible = "regulator-gpio";
> + regulator-name = "tlv71033";
> + pinctrl-names = "default";
> + pinctrl-0 = <&vdd_sd_dv_pins_default>;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + vin-supply = <&vsys_5v0>;
> + gpios = <&main_gpio0 8 GPIO_ACTIVE_HIGH>;
> + states = <1800000 0x0>,
> + <3300000 0x1>;
> + };
> +};
> +
> +&main_pmx0 {
> + main_uart8_pins_default: main-uart8-pins-default {
> + pinctrl-single,pins = <
> + J784S4_IOPAD(0x040, PIN_INPUT, 14) /* (AF37) MCASP0_AXR0.UART8_CTSn */
> + J784S4_IOPAD(0x044, PIN_OUTPUT, 14) /* (AG37) MCASP0_AXR1.UART8_RTSn */
> + J784S4_IOPAD(0x0d0, PIN_INPUT, 11) /* (AP38) SPI0_CS1.UART8_RXD */
> + J784S4_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AN38) SPI0_CLK.UART8_TXD */
> + >;
> + };
> +
> + main_i2c0_pins_default: main-i2c0-pins-default {
> + pinctrl-single,pins = <
> + J784S4_IOPAD(0x0e0, PIN_INPUT_PULLUP, 0) /* (AN36) I2C0_SCL */
> + J784S4_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AP37) I2C0_SDA */
> + >;
> + };
> +
> + main_mmc1_pins_default: main-mmc1-pins-default {
> + pinctrl-single,pins = <
> + J784S4_IOPAD(0x104, PIN_INPUT, 0) /* (AB38) MMC1_CLK */
> + J784S4_IOPAD(0x108, PIN_INPUT, 0) /* (AB36) MMC1_CMD */
> + J784S4_IOPAD(0x100, PIN_INPUT, 0) /* (No Pin) MMC1_CLKLB */
> + J784S4_IOPAD(0x0fc, PIN_INPUT, 0) /* (AA33) MMC1_DAT0 */
> + J784S4_IOPAD(0x0f8, PIN_INPUT, 0) /* (AB34) MMC1_DAT1 */
> + J784S4_IOPAD(0x0f4, PIN_INPUT, 0) /* (AA32) MMC1_DAT2 */
> + J784S4_IOPAD(0x0f0, PIN_INPUT, 0) /* (AC38) MMC1_DAT3 */
> + J784S4_IOPAD(0x0e8, PIN_INPUT, 8) /* (AR38) TIMER_IO0.MMC1_SDCD */
> + >;
> + };
> +
> + vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
> + pinctrl-single,pins = <
> + J784S4_IOPAD(0x020, PIN_INPUT, 7) /* (AJ35) MCAN15_RX.GPIO0_8 */
> + >;
> + };
> +};
> +
> +&main_uart8 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_uart8_pins_default>;
> +};
> +
> +&main_i2c0 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c0_pins_default>;
> +
> + clock-frequency = <400000>;
> +
> + exp1: gpio at 20 {
> + compatible = "ti,tca6416";
> + reg = <0x20>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-line-names = "PCIE1_2L_MODE_SEL", "PCIE1_4L_PERSTZ", "PCIE1_2L_RC_RSTZ",
> + "PCIE1_2L_EP_RST_EN", "PCIE0_4L_MODE_SEL", "PCIE0_4L_PERSTZ",
> + "PCIE0_4L_RC_RSTZ", "PCIE0_4L_EP_RST_EN", "PCIE1_4L_PRSNT#",
> + "PCIE0_4L_PRSNT#", "CDCI1_OE1/OE4", "CDCI1_OE2/OE3",
> + "AUDIO_MUX_SEL", "EXP_MUX2", "EXP_MUX3", "GESI_EXP_PHY_RSTZ";
> + };
> +
> + exp2: gpio at 22 {
> + compatible = "ti,tca6424";
> + reg = <0x22>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-line-names = "R_GPIO_RGMII1_RST", "ENET2_I2CMUX_SEL", "GPIO_USD_PWR_EN",
> + "USBC_PWR_EN", "USBC_MODE_SEL1", "USBC_MODE_SEL0",
> + "GPIO_LIN_EN", "R_CAN_STB", "CTRL_PM_I2C_OE#",
> + "ENET2_EXP_PWRDN", "ENET2_EXP_SPARE2", "CDCI2_RSTZ",
> + "USB2.0_MUX_SEL", "CANUART_MUX_SEL0", "CANUART_MUX2_SEL1",
> + "CANUART_MUX1_SEL1", "ENET1_EXP_PWRDN", "ENET1_EXP_RESETZ",
> + "ENET1_I2CMUX_SEL", "ENET1_EXP_SPARE2", "ENET2_EXP_RESETZ",
> + "USER_INPUT1", "USER_LED1", "USER_LED2";
> + };
> +};
> +
> +&main_sdhci1 {
> + /* SD card */
> + status = "okay";
> + pinctrl-0 = <&main_mmc1_pins_default>;
> + pinctrl-names = "default";
> + disable-wp;
> + vmmc-supply = <&vdd_mmc1>;
> + vqmmc-supply = <&vdd_sd_dv>;
> +};
> +
> +&main_gpio0 {
> + status = "okay";
> +};
More information about the linux-arm-kernel
mailing list