[PATCH V2 2/2] arm64: dts: Add basic support for BIQU CB1
Jernej Škrabec
jernej.skrabec at gmail.com
Mon Nov 14 12:16:29 PST 2022
Hi Martin,
Dne ponedeljek, 14. november 2022 ob 18:20:16 CET je Martin Botka napisal(a):
> CB1 is Compute Module style board that plugs into Rpi board style adapter or
> Manta 3D printer boards (M4P/M8P).
>
> The board has:
> H616 SoC
> 1GB of RAM
> AXP313A PMIC
>
> And the actual boards that CB1 plugs in are just extension to it with ports
> and thus are not split in DT.
>
> Boards have:
> 4x (3x for Manta boards) USB and 1 USB OTG.
> SDcard slot for loading images.
> Ethernet port wired to the internal PHY.
> 2x HDMI 2.0.
> Power and Status LEDs.
>
> Currently working:
> Booting
> USB
> UART
>
> Signed-off-by: Martin Botka <martin.botka at somainline.org>
> ---
> Changes in V2:
> Add proper board compatible
> Add regulator prefix for vcc5v
> Drop okay status from PMIC
> Drop standby_param
> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> .../dts/allwinner/sun50i-h616-biqu-cb1.dts | 186 ++++++++++++++++++
> 2 files changed, 187 insertions(+)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-biqu-cb1.dts
>
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile
> b/arch/arm64/boot/dts/allwinner/Makefile index 6a96494a2e0a..223f1be73541
> 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -38,5 +38,6 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-biqu-cb1.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-biqu-cb1.dts
> b/arch/arm64/boot/dts/allwinner/sun50i-h616-biqu-cb1.dts new file mode
> 100644
> index 000000000000..297536d7629a
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-biqu-cb1.dts
> @@ -0,0 +1,186 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2022 Arm Ltd.
I suppose Arm Ltd. has nothing to do with this board? Put yours copyrights
there.
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h616.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/leds/common.h>
> +
> +/ {
> + model = "BIQU CB1";
> + compatible = "biqu,cb1", "allwinner,sun50i-h616";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led-0 {
> + function = LED_FUNCTION_POWER;
> + color = <LED_COLOR_ID_RED>;
> + gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /*
PC12 */
> + default-state = "on";
> + };
> +
> + led-1 {
> + function = LED_FUNCTION_STATUS;
> + color = <LED_COLOR_ID_GREEN>;
> + gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /*
PC13 */
> + };
> + };
> +
> + reg_vcc5v: regulator_vcc5v {
> + /* board wide 5V supply directly from the USB-C socket
*/
> + compatible = "regulator-fixed";
> + regulator-name = "vcc-5v";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + reg_usb1_vbus: regulator-usb1-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb1-vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <®_vcc5v>;
> + enable-active-high;
> + gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
> + };
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> +
> +&ehci2 {
> + status = "okay";
> +};
> +
> +&ehci3 {
> + status = "okay";
> +};
> +
> +&mmc0 {
> + vmmc-supply = <®_dldo1>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
> + no-1-8-v;
> + bus-width = <4>;
> + status = "disabled";
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +&ohci1 {
> + status = "okay";
> +};
> +
> +&ohci2 {
> + status = "okay";
> +};
> +
> +&ohci3 {
> + status = "okay";
> +};
> +
> +&r_i2c {
> + status = "okay";
> +
> + axp1530: pmic at 36 {
> + compatible = "x-powers,axp1530";
I see that you send driver for this PMIC separately. Next time please mention
that this series depends on another, otherwise checks will fail. Ping us here
once PMIC driver is merged to unblock this.
Anyway, RSB is prefered. Can you switch to it?
> + reg = <0x36>;
> + wakeup-source;
> +
> + regulators{
> + reg_dcdc1: dcdc1 {
> + regulator-name = "axp1530-dcdc1";
> + regulator-min-microvolt =
<500000>;
> + regulator-max-microvolt =
<3400000>;
> + regulator-step-delay-us = <25>;
> + regulator-final-delay-us = <50>;
> + regulator-always-on;
> + };
> +
> + reg_dcdc2: dcdc2 {
> + regulator-name = "axp1530-dcdc2";
> + regulator-min-microvolt =
<500000>;
> + regulator-max-microvolt =
<1540000>;
> + regulator-step-delay-us = <25>;
> + regulator-final-delay-us = <50>;
> + regulator-ramp-delay = <200>;
> + regulator-always-on;
> + };
> +
> + reg_dcdc3: dcdc3 {
> + regulator-name = "axp1530-dcdc3";
> + regulator-min-microvolt =
<500000>;
> + regulator-max-microvolt =
<1840000>;
> + regulator-step-delay-us = <25>;
> + regulator-final-delay-us = <50>;
> + regulator-always-on;
> + };
> +
> + reg_aldo1: ldo1 {
> + regulator-name = "axp1530-aldo1";
> + regulator-min-microvolt =
<1800000>;
> + regulator-max-microvolt =
<1800000>;
> + regulator-step-delay-us = <25>;
> + regulator-final-delay-us = <50>;
> + regulator-always-on;
> + };
> +
> + reg_dldo1: ldo2 {
> + regulator-name = "axp1530-dldo1";
> + regulator-min-microvolt =
<3300000>;
> + regulator-max-microvolt =
<3300000>;
> + regulator-step-delay-us = <25>;
> + regulator-final-delay-us = <50>;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_ph_pins>;
> + status = "okay";
> +};
> +
> +&usbotg {
> + /*
> + * PHY0 pins are connected to a USB-C socket, but a role switch
> + * is not implemented: both CC pins are pulled to GND.
> + * The VBUS pins power the device, so a fixed peripheral mode
> + * is the best choice.
> + * The board can be powered via GPIOs, in this case port0 *can*
> + * act as a host (with a cable/adapter ignoring CC), as VBUS is
> + * then provided by the GPIOs. Any user of this setup would
> + * need to adjust the DT accordingly: dr_mode set to "host",
> + * enabling OHCI0 and EHCI0.
> + */
Above text is verbatim copy from OrangePi Zero2 and I'm not sure if it is
fully accurate for this board too. Looking at board photo, it surely looks
like this board has same USB design as Zero2. But if that's true, you
shouldn't enable OHCI0 and EHCI0 nodes.
Is there any board schematic publicly available for this board?
Best regards,
Jernej
> + dr_mode = "peripheral";
> + status = "okay";
> +};
> +
> +&usbphy {
> + usb1_vbus-supply = <®_usb1_vbus>;
> + status = "okay";
> +};
More information about the linux-arm-kernel
mailing list