[PATCH v3 RESEND net-next 2/3] net: axienet: set mdio clock according to bus-frequency

[Andy Chiu]

Some FPGA platforms have 80KHz MDIO bus frequency constraint when
connecting Ethernet to its on-board external Marvell PHY. Thus, we may
have to set MDIO clock according to the DT. Otherwise, use the default
2.5 MHz, as specified by 802.3, if the entry is not present.

Signed-off-by: Andy Chiu <andy.chiu at sifive.com>
Reviewed-by: Greentime Hu <greentime.hu at sifive.com>
---
 .../net/ethernet/xilinx/xilinx_axienet_mdio.c | 46 +++++++++++++------
 1 file changed, 32 insertions(+), 14 deletions(-)

diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_mdio.c b/drivers/net/ethernet/xilinx/xilinx_axienet_mdio.c
index e1f51a071888..5e1619ce8074 100644
--- a/drivers/net/ethernet/xilinx/xilinx_axienet_mdio.c
+++ b/drivers/net/ethernet/xilinx/xilinx_axienet_mdio.c
@@ -147,15 +147,18 @@ static int axienet_mdio_write(struct mii_bus *bus, int phy_id, int reg,
 /**
  * axienet_mdio_enable - MDIO hardware setup function
  * @lp:		Pointer to axienet local data structure.
+ * @np:		Pointer to mdio device tree node.
  *
  * Return:	0 on success, -ETIMEDOUT on a timeout.
  *
  * Sets up the MDIO interface by initializing the MDIO clock and enabling the
  * MDIO interface in hardware.
  **/
-static int axienet_mdio_enable(struct axienet_local *lp)
+static int axienet_mdio_enable(struct axienet_local *lp, struct device_node *np)
 {
+	u32 mdio_freq = MAX_MDIO_FREQ;
 	u32 host_clock;
+	u32 clk_div;
 
 	lp->mii_clk_div = 0;
 
@@ -184,6 +187,12 @@ static int axienet_mdio_enable(struct axienet_local *lp)
 			    host_clock);
 	}
 
+	if (np)
+		of_property_read_u32(np, "clock-frequency", &mdio_freq);
+	if (mdio_freq != MAX_MDIO_FREQ)
+		netdev_info(lp->ndev, "Setting non-standard mdio bus frequency to %u Hz\n",
+			    mdio_freq);
+
 	/* clk_div can be calculated by deriving it from the equation:
 	 * fMDIO = fHOST / ((1 + clk_div) * 2)
 	 *
@@ -209,13 +218,20 @@ static int axienet_mdio_enable(struct axienet_local *lp)
 	 * "clock-frequency" from the CPU
 	 */
 
-	lp->mii_clk_div = (host_clock / (MAX_MDIO_FREQ * 2)) - 1;
+	clk_div = (host_clock / (mdio_freq * 2)) - 1;
 	/* If there is any remainder from the division of
-	 * fHOST / (MAX_MDIO_FREQ * 2), then we need to add
+	 * fHOST / (mdio_freq * 2), then we need to add
 	 * 1 to the clock divisor or we will surely be above 2.5 MHz
 	 */
-	if (host_clock % (MAX_MDIO_FREQ * 2))
-		lp->mii_clk_div++;
+	if (host_clock % (mdio_freq * 2))
+		clk_div++;
+
+	/* Check for overflow of mii_clk_div */
+	if (clk_div & ~XAE_MDIO_MC_CLOCK_DIVIDE_MAX) {
+		netdev_warn(lp->ndev, "MDIO clock divisor overflow\n");
+		return -EOVERFLOW;
+	}
+	lp->mii_clk_div = (u8)clk_div;
 
 	netdev_dbg(lp->ndev,
 		   "Setting MDIO clock divisor to %u/%u Hz host clock.\n",
@@ -242,10 +258,6 @@ int axienet_mdio_setup(struct axienet_local *lp)
 	struct mii_bus *bus;
 	int ret;
 
-	ret = axienet_mdio_enable(lp);
-	if (ret < 0)
-		return ret;
-
 	bus = mdiobus_alloc();
 	if (!bus)
 		return -ENOMEM;
@@ -261,15 +273,21 @@ int axienet_mdio_setup(struct axienet_local *lp)
 	lp->mii_bus = bus;
 
 	mdio_node = of_get_child_by_name(lp->dev->of_node, "mdio");
+	ret = axienet_mdio_enable(lp, mdio_node);
+	if (ret < 0)
+		goto unregister;
 	ret = of_mdiobus_register(bus, mdio_node);
+	if (ret)
+		goto unregister;
 	of_node_put(mdio_node);
-	if (ret) {
-		mdiobus_free(bus);
-		lp->mii_bus = NULL;
-		return ret;
-	}
 	axienet_mdio_mdc_disable(lp);
 	return 0;
+
+unregister:
+	of_node_put(mdio_node);
+	mdiobus_free(bus);
+	lp->mii_bus = NULL;
+	return ret;
 }
 
 /**
-- 
2.36.0