[PATCH V4 04/14] arm64: dts: imx8mp-evk: enable uart1/3 ports

[Peng Fan (OSS)]

From: Peng Fan <peng.fan at nxp.com>

Enable uart1/3 ports for evk board.
Configure the clock to source from IMX8MP_SYS_PLL1_80M, because the uart
could only support max 1.5M buadrate if using OSC_24M as clock source.

Signed-off-by: Peng Fan <peng.fan at nxp.com>
Reviewed-by: Marco Felsch <m.felsch at pengutronix.de>
---
 arch/arm64/boot/dts/freescale/imx8mp-evk.dts | 36 ++++++++++++++++++++
 1 file changed, 36 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
index e323e6f4b7e5..29472502d547 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
@@ -412,6 +412,15 @@ &snvs_pwrkey {
 	status = "okay";
 };
 
+&uart1 { /* BT */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	assigned-clocks = <&clk IMX8MP_CLK_UART1>;
+	assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_80M>;
+	fsl,uart-has-rtscts;
+	status = "okay";
+};
+
 &uart2 {
 	/* console */
 	pinctrl-names = "default";
@@ -434,6 +443,15 @@ &usb_dwc3_1 {
 	status = "okay";
 };
 
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	assigned-clocks = <&clk IMX8MP_CLK_UART3>;
+	assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_80M>;
+	fsl,uart-has-rtscts;
+	status = "okay";
+};
+
 &usdhc2 {
 	assigned-clocks = <&clk IMX8MP_CLK_USDHC2>;
 	assigned-clock-rates = <400000000>;
@@ -609,6 +627,15 @@ MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19	0x40
 		>;
 	};
 
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX	0x140
+			MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX	0x140
+			MX8MP_IOMUXC_UART3_RXD__UART1_DCE_CTS	0x140
+			MX8MP_IOMUXC_UART3_TXD__UART1_DCE_RTS	0x140
+		>;
+	};
+
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
 			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX	0x140
@@ -622,6 +649,15 @@ MX8MP_IOMUXC_GPIO1_IO14__USB2_OTG_PWR	0x10
 		>;
 	};
 
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_ECSPI1_SCLK__UART3_DCE_RX		0x140
+			MX8MP_IOMUXC_ECSPI1_MOSI__UART3_DCE_TX		0x140
+			MX8MP_IOMUXC_ECSPI1_SS0__UART3_DCE_RTS		0x140
+			MX8MP_IOMUXC_ECSPI1_MISO__UART3_DCE_CTS		0x140
+		>;
+	};
+
 	pinctrl_usdhc2: usdhc2grp {
 		fsl,pins = <
 			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK	0x190
-- 
2.37.1