[PATCH v2 3/3] nvmem: stm32: detect bsec pta presence for STM32MP15x

[Patrick Delaunay]

On STM32MP15x SoC, the SMC backend is optional when OP-TEE is used;
the PTA BSEC should be used as it is done on STM32MP13x platform,
but the BSEC SMC can be also used: it is a legacy mode in OP-TEE,
not recommended but used in previous OP-TEE firmware.

The presence of OP-TEE is dynamically detected in STM32MP15x device tree
and the supported NVMEM backend is dynamically detected:
- PTA with stm32_bsec_pta_find
- SMC with stm32_bsec_check

With OP-TEE but without PTA and SMC detection, the probe is deferred for
STM32MP15x devices.

On STM32MP13x platform, only the PTA is supported with cfg->ta = true
and this detection is skipped.

Signed-off-by: Patrick Delaunay <patrick.delaunay at foss.st.com>
---

Changes in v2:
- Added patch in the serie for BSEC PTA support on STM32MP15x
  with dynamic detection of OP-TEE presence and SMC support (legacy mode)

 drivers/nvmem/stm32-romem.c | 37 +++++++++++++++++++++++++++++++++----
 1 file changed, 33 insertions(+), 4 deletions(-)

diff --git a/drivers/nvmem/stm32-romem.c b/drivers/nvmem/stm32-romem.c
index 0a0e29d09b67..35997d581c9d 100644
--- a/drivers/nvmem/stm32-romem.c
+++ b/drivers/nvmem/stm32-romem.c
@@ -526,6 +526,31 @@ static int stm32_bsec_write(void *context, unsigned int offset, void *buf,
 	return 0;
 }
 
+static bool stm32_bsec_smc_check(void)
+{
+	u32 val;
+	int ret;
+
+	/* check that the OP-TEE support the BSEC SMC (legacy mode) */
+	ret = stm32_bsec_smc(STM32_SMC_READ_SHADOW, 0, 0, &val);
+
+	return !ret;
+}
+
+static bool optee_presence_check(void)
+{
+	struct device_node *np;
+	bool tee_detected = false;
+
+	/* check that the OP-TEE node is present and available. */
+	np = of_find_node_by_path("/firmware/optee");
+	if (np && of_device_is_available(np))
+		tee_detected = true;
+	of_node_put(np);
+
+	return tee_detected;
+}
+
 static int stm32_romem_probe(struct platform_device *pdev)
 {
 	const struct stm32_romem_cfg *cfg;
@@ -561,14 +586,18 @@ static int stm32_romem_probe(struct platform_device *pdev)
 	} else {
 		priv->cfg.size = cfg->size;
 		priv->lower = cfg->lower;
-		if (cfg->ta) {
+		if (cfg->ta || optee_presence_check()) {
 			priv->ta = stm32_bsec_pta_find(dev);
 			/* wait for OP-TEE client driver to be up and ready */
-			if (!priv->ta)
-				return -EPROBE_DEFER;
+			if (!priv->ta) {
+				/* BSEC PTA is required or SMC not ready */
+				if (cfg->ta || !stm32_bsec_smc_check())
+					return -EPROBE_DEFER;
+			}
 			if (IS_ERR(priv->ta))
 				return PTR_ERR(priv->ta);
-
+		}
+		if (priv->ta) {
 			priv->cfg.reg_read = stm32_bsec_pta_read;
 			priv->cfg.reg_write = stm32_bsec_pta_write;
 		} else {
-- 
2.25.1