[PATCH v2 2/2] arm64: dts: ti: Add support for phyBOARD-Electra-AM642
Krzysztof Kozlowski
krzysztof.kozlowski at linaro.org
Tue Nov 8 10:01:46 PST 2022
On 08/11/2022 18:50, Wadim Egorov wrote:
> Add basic support for phyCORE-AM64x SoM & phyBOARD-Electra-AM642 CB.
>
> The phyCORE-AM64x [1] is a SoM (System on Module) featuring TI's AM64x SoC.
> It can be used in combination with different carrier boards.
> This module can come with different sizes and models for
> DDR, eMMC, SPI NOR Flash and various SoCs from the AM64x family.
>
> A development Kit, called phyBOARD-Electra [2] is used as a carrier board
> reference design around the AM64x SoM.
>
> Supported features:
> * Debug UART
> * Heartbeat LED
> * GPIO buttons & LEDs
> * SPI NOR flash
> * SPI TPM Chip
> * eMMC
> * CAN
> * Ethernet
> * Micro SD card
> * I2C EEPROM
> * I2C RTC
> * I2C LED Dimmer
> * USB
>
> For more details, see:
>
> [1] Product page SoM: https://www.phytec.com/product/phycore-am64x
> [2] Product page CB: https://www.phytec.com/product/phyboard-am64x
>
> Signed-off-by: Wadim Egorov <w.egorov at phytec.de>
> ---
> v2:
> - Update commit message
> - Add links to product pages for SoM & CB
> - Drop "fixed" from regulator node names
> - Use generic node names for pmic, tpm, leds & keys
> - Update compatible of som.dtsi
> - Remove not needed node labels for pmic, tpm
> - Remove not needed R5 core mailbox & reserved memory definitions
> This is use case specific and should not be defined in the som.dtsi
> - Provide aliases for used devices by SoM & CB
> - Fixed led definition: Provide proper default-trigger, function & color
> - Renamed rtc label to i2c_som_rtc
> ---
> arch/arm64/boot/dts/ti/Makefile | 1 +
> .../boot/dts/ti/k3-am64-phycore-som.dtsi | 286 ++++++++++++++++
> .../dts/ti/k3-am642-phyboard-electra-rdk.dts | 321 ++++++++++++++++++
> 3 files changed, 608 insertions(+)
> create mode 100644 arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi
> create mode 100644 arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts
>
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index 4555a5be2257..79331f16cd4b 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-j721s2-common-proc-board.dtb
>
> dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
> +dtb-$(CONFIG_ARCH_K3) += k3-am642-phyboard-electra-rdk.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb
>
> dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb
> diff --git a/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi
> new file mode 100644
> index 000000000000..86e6b87b826a
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi
> @@ -0,0 +1,286 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2021 PHYTEC America, LLC - https://www.phytec.com
> + * Author: Matt McKee <mmckee at phytec.com>
> + *
> + * Copyright (C) 2022 PHYTEC Messtechnik GmbH
> + * Author: Wadim Egorov <w.egorov at phytec.de>
> + *
> + * Product homepage:
> + * https://www.phytec.com/product/phycore-am64x
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/net/ti-dp83867.h>
> +
> +/ {
> + model = "PHYTEC phyCORE-AM64x";
> + compatible = "phytec,am64-phycore-som", "ti,am642";
> +
> + aliases {
> + ethernet0 = &cpsw_port1;
> + mmc0 = &sdhci0;
> + rtc0 = &i2c_som_rtc;
> + };
> +
> + memory at 80000000 {
> + device_type = "memory";
> + reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + secure_ddr: optee at 9e800000 {
> + reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
> + alignment = <0x1000>;
> + no-map;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led-0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&leds_pins_default>;
> + color = <LED_COLOR_ID_GREEN>;
> + gpios = <&main_gpio0 12 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + function = LED_FUNCTION_HEARTBEAT;
> + };
> + };
> +
> + vcc_5v0_som: vcc-5v0-som {
I asked to drop "fixed", not other generic parts.
Node names should be generic.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + /* VIN / VCC_5V0_SOM */
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_5V0_SOM";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +};
> +
> +&main_pmx0 {
> + cpsw_mdio_pins_default: cpsw-mdio-pins-default {
> + pinctrl-single,pins = <
> + AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */
> + AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */
> + AM64X_IOPAD(0x0100, PIN_OUTPUT, 7) /* (V7) PRG1_PRU0_GPO18.GPIO0_63 */
> + >;
> + };
> +
> + cpsw_rgmii1_pins_default: cpsw-rgmii1-pins-default {
> + pinctrl-single,pins = <
> + AM64X_IOPAD(0x0184, PIN_INPUT, 4) /* (W6) PRG0_PRU0_GPO9.RGMII1_RX_CTL */
> + AM64X_IOPAD(0x0188, PIN_INPUT, 4) /* (AA5) PRG0_PRU0_GPO10.RGMII1_RXC */
> + AM64X_IOPAD(0x00dc, PIN_OUTPUT, 4) /* (U15) PRG1_PRU0_GPO9.RGMII1_TX_CTL */
> + AM64X_IOPAD(0x00e0, PIN_OUTPUT, 4) /* (U14) PRG1_PRU0_GPO10.RGMII1_TXC */
> + AM64X_IOPAD(0x01cc, PIN_INPUT, 4) /* (W5) PRG0_PRU1_GPO7.RGMII1_RD0 */
> + AM64X_IOPAD(0x0124, PIN_OUTPUT, 4) /* (V15) PRG1_PRU1_GPO7.RGMII1_TD0 */
> + AM64X_IOPAD(0x01d4, PIN_INPUT, 4) /* (Y5) PRG0_PRU1_GPO9.RGMII1_RD1 */
> + AM64X_IOPAD(0x012c, PIN_OUTPUT, 4) /* (V14) PRG1_PRU1_GPO9.RGMII1_TD1 */
> + AM64X_IOPAD(0x01d8, PIN_INPUT, 4) /* (V6) PRG0_PRU1_GPO10.RGMII1_RD2 */
> + AM64X_IOPAD(0x0130, PIN_OUTPUT, 4) /* (W14) PRG1_PRU1_GPO10.RGMII1_TD2 */
> + AM64X_IOPAD(0x01f4, PIN_INPUT, 4) /* (V5) PRG0_PRU1_GPO17.RGMII1_RD3 */
> + AM64X_IOPAD(0x014c, PIN_OUTPUT, 4) /* (AA14) PRG1_PRU1_GPO17.RGMII1_TD3 */
> + AM64X_IOPAD(0x0154, PIN_INPUT, 7) /* (V12) PRG1_PRU1_GPO19.GPIO0_84 */
> + >;
> + };
> +
> + eeprom_wp_pins_default: eeprom-wp-pins-default {
> + pinctrl-single,pins = <
> + AM64X_IOPAD(0x0208, PIN_OUTPUT, 7) /* (D12) SPI0_CS0.GPIO1_42 */
> + >;
> + };
> +
> + leds_pins_default: leds-pins-default {
> + pinctrl-single,pins = <
> + AM64X_IOPAD(0x0030, PIN_OUTPUT, 7) /* (L18) OSPI0_CSn1.GPIO0_12 */
> + >;
> + };
> +
> + main_i2c0_pins_default: main-i2c0-pins-default {
> + pinctrl-single,pins = <
> + AM64X_IOPAD(0x0260, PIN_INPUT, 0) /* (A18) I2C0_SCL */
> + AM64X_IOPAD(0x0264, PIN_INPUT, 0) /* (B18) I2C0_SDA */
> + >;
> + };
> +
> + ospi0_pins_default: ospi0-pins-default {
> + pinctrl-single,pins = <
> + AM64X_IOPAD(0x0000, PIN_OUTPUT, 0) /* (N20) OSPI0_CLK */
> + AM64X_IOPAD(0x0008, PIN_INPUT, 0) /* (N19) OSPI0_DQS */
> + AM64X_IOPAD(0x000c, PIN_INPUT, 0) /* (M19) OSPI0_D0 */
> + AM64X_IOPAD(0x0010, PIN_INPUT, 0) /* (M18) OSPI0_D1 */
> + AM64X_IOPAD(0x0014, PIN_INPUT, 0) /* (M20) OSPI0_D2 */
> + AM64X_IOPAD(0x0018, PIN_INPUT, 0) /* (M21) OSPI0_D3 */
> + AM64X_IOPAD(0x001c, PIN_INPUT, 0) /* (P21) OSPI0_D4 */
> + AM64X_IOPAD(0x0020, PIN_INPUT, 0) /* (P20) OSPI0_D5 */
> + AM64X_IOPAD(0x0024, PIN_INPUT, 0) /* (N18) OSPI0_D6 */
> + AM64X_IOPAD(0x0028, PIN_INPUT, 0) /* (M17) OSPI0_D7 */
> + AM64X_IOPAD(0x002c, PIN_OUTPUT, 0) /* (L19) OSPI0_CSn0 */
> + >;
> + };
> +};
> +
> +&cpsw3g {
> + pinctrl-names = "default";
> + pinctrl-0 = <&cpsw_rgmii1_pins_default>;
> +};
> +
> +&cpsw3g_mdio {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&cpsw_mdio_pins_default>;
> +
> + cpsw3g_phy1: ethernet-phy at 1 {
> + compatible = "ethernet-phy-id2000.a231", "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + interrupt-parent = <&main_gpio0>;
> + interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> + reset-gpios = <&main_gpio0 63 GPIO_ACTIVE_LOW>;
> + reset-assert-us = <1000>;
> + reset-deassert-us = <1000>;
> + };
> +};
> +
> +&cpsw_port1 {
> + phy-mode = "rgmii-rxid";
> + phy-handle = <&cpsw3g_phy1>;
> +};
> +
> +&cpsw_port2 {
> + status = "disabled";
> +};
> +
> +&mailbox0_cluster2 {
> + status = "disabled";
> +};
> +
> +&mailbox0_cluster3 {
> + status = "disabled";
> +};
> +
> +&mailbox0_cluster4 {
> + status = "disabled";
> +};
> +
> +&mailbox0_cluster5 {
> + status = "disabled";
> +};
> +
> +&mailbox0_cluster6 {
> + status = "disabled";
> +};
> +
> +&mailbox0_cluster7 {
> + status = "disabled";
> +};
> +
> +&main_i2c0 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c0_pins_default>;
> + clock-frequency = <400000>;
> +
> + eeprom at 50 {
> + compatible = "atmel,24c32";
> + pinctrl-names = "default";
> + pinctrl-0 = <&eeprom_wp_pins_default>;
> + pagesize = <32>;
> + reg = <0x50>;
> + };
> +
> + i2c_som_rtc: rtc at 52 {
> + compatible = "microcrystal,rv3028";
> + reg = <0x52>;
> + trickle-resistor-ohms = <3000>;
> + };
> +
> + pmic at 61 {
> + compatible = "ti,lp8733";
> + reg = <0x61>;
> +
> + buck0-in-supply =<&vcc_5v0_som>;
> + buck1-in-supply =<&vcc_5v0_som>;
> + ldo0-in-supply =<&vdd_3v3>;
> + ldo1-in-supply =<&vdd_3v3>;
> +
> + regulators {
> + vdd_core: buck0 {
> + regulator-name = "VDD_CORE";
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <750000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vdd_3v3: buck1 {
> + regulator-name = "VDD_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vdd_1v8_ldo0: ldo0 {
> + regulator-name = "VDD_1V8_LDO0";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vdda_1v8: ldo1 {
> + regulator-name = "VDDA_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +/* mcu_gpio0 is reserved for mcu firmware usage */
> +&mcu_gpio0 {
> + status = "reserved";
> +};
> +
> +&ospi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ospi0_pins_default>;
> +
> + flash at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0x0>;
> + spi-tx-bus-width = <8>;
> + spi-rx-bus-width = <8>;
> + spi-max-frequency = <25000000>;
> + cdns,tshsl-ns = <60>;
> + cdns,tsd2d-ns = <60>;
> + cdns,tchsh-ns = <60>;
> + cdns,tslch-ns = <60>;
> + cdns,read-delay = <0>;
> + };
> +};
> +
> +&sdhci0 {
> + bus-width = <8>;
> + non-removable;
> + ti,driver-strength-ohm = <50>;
> + disable-wp;
> + keep-power-in-suspend;
> +};
> +
> +/* adc0 is reserved for R5 usage */
> +&tscadc0 {
> + status = "reserved";
> +};
> diff --git a/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts b/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts
> new file mode 100644
> index 000000000000..15c554cd6fe4
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts
> @@ -0,0 +1,321 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2021 PHYTEC America, LLC - https://www.phytec.com
> + * Author: Matt McKee <mmckee at phytec.com>
> + *
> + * Copyright (C) 2022 PHYTEC Messtechnik GmbH
> + * Author: Wadim Egorov <w.egorov at phytec.de>
> + *
> + * Product homepage:
> + * https://www.phytec.com/product/phyboard-am64x
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/leds/leds-pca9532.h>
> +#include <dt-bindings/mux/ti-serdes.h>
> +#include <dt-bindings/phy/phy.h>
> +#include "k3-am642.dtsi"
> +#include "k3-am64-phycore-som.dtsi"
> +
> +/ {
> + compatible = "phytec,am642-phyboard-electra-rdk",
> + "phytec,am64-phycore-som", "ti,am642";
> + model = "PHYTEC phyBOARD-Electra-AM64x RDK";
> +
> + aliases {
> + mmc1 = &sdhci1;
> + serial2 = &main_uart0;
> + serial3 = &main_uart1;
> + };
> +
> + chosen {
> + stdout-path = &main_uart0;
> + };
> +
> + can_tc1: can-phy0 {
> + compatible = "ti,tcan1042";
> + pinctrl-names = "default";
> + pinctrl-0 = <&can_tc1_pins_default>;
> + #phy-cells = <0>;
> + max-bitrate = <5000000>;
> + standby-gpios = <&main_gpio0 32 GPIO_ACTIVE_HIGH>;
> + };
> +
> + can_tc2: can-phy1 {
> + compatible = "ti,tcan1042";
> + pinctrl-names = "default";
> + pinctrl-0 = <&can_tc2_pins_default>;
> + #phy-cells = <0>;
> + max-bitrate = <5000000>;
> + standby-gpios = <&main_gpio0 35 GPIO_ACTIVE_HIGH>;
> + };
> +
> + keys {
> + compatible = "gpio-keys";
> + autorepeat;
> + pinctrl-names = "default";
> + pinctrl-0 = <&gpio_keys_pins_default>;
> +
> + key-home {
> + label = "home";
> + linux,code = <KEY_HOME>;
> + gpios = <&main_gpio0 17 GPIO_ACTIVE_HIGH>;
> + };
> +
> + key-menu {
> + label = "menu";
> + linux,code = <KEY_MENU>;
> + gpios = <&main_gpio0 21 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&user_leds_pins_default>;
> +
> + led-1 {
> + color = <LED_COLOR_ID_RED>;
> + gpios = <&main_gpio0 15 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "mmc0";
> + function = LED_FUNCTION_DISK;
> + };
> +
> + led-2 {
> + color = <LED_COLOR_ID_GREEN>;
> + gpios = <&main_gpio0 16 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "mmc1";
> + function = LED_FUNCTION_DISK;
> + };
> + };
> +
> + vcc_3v3_mmc: regulator-sd {
This is a friendly reminder during the review process.
It seems my previous comments were not fully addressed. Maybe my
feedback got lost between the quotes, maybe you just forgot to apply it.
Please go back to the previous discussion and either implement all
requested changes or keep discussing them.
Thank you.
Best regards,
Krzysztof
More information about the linux-arm-kernel
mailing list