[PATCH v2 5/5] arm64: dts: uniphier: Add NX1 SoC and boards support
Kunihiko Hayashi
hayashi.kunihiko at socionext.com
Mon Nov 7 02:34:10 PST 2022
Initial version of devicetree sources for NX1 SoC and boards.
NX1 SoC belongs to the UniPhier armv8 architecture platform, and is
designed for IoT and AI/ML application fields.
This SoC has four Cortex-A53 cores and basically peripherals compatible
with the previous UniPhier SoCs: PCIe Gen2, USB3.1/2.0, eMMC/SD,
1G Ethernet, UART, GPIO, FI2C, SPI, DMAC, and Video Out.
The SOM is a small module that has only the peripherals necessary for
booting: UART, FI2C for EEPROM, eMMC and SD. The reference board has
other peripherals and external LED IC, and is in conjunction with SOM.
PCIe works as an endpoint as default.
The EVB is a standalone board that has all supported peripherals.
PCIe works as a host controller as default. This SoC has only 190MB of
PCIe space, so the possible endpoint devices are limited, but it is
assumed that the reference board will be connected.
This devicetree has two restrictions:
- SD cards that works at 1.8V are not supported, because the power
supply switching function is in the system controller and needs to be
controlled by the driver.
- This SoC has two USB ports, each with an HS-PHY and an SS-PHY, however,
DWC3 can only specify one HS-PHY and one SS-PHY, so the PHYs on the
second port are not currently specified.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko at socionext.com>
---
arch/arm64/boot/dts/socionext/Makefile | 3 +
.../boot/dts/socionext/uniphier-nx1-evb.dts | 87 +++
.../boot/dts/socionext/uniphier-nx1-ref.dts | 109 +++
.../boot/dts/socionext/uniphier-nx1-som.dts | 54 ++
.../boot/dts/socionext/uniphier-nx1.dtsi | 702 ++++++++++++++++++
5 files changed, 955 insertions(+)
create mode 100644 arch/arm64/boot/dts/socionext/uniphier-nx1-evb.dts
create mode 100644 arch/arm64/boot/dts/socionext/uniphier-nx1-ref.dts
create mode 100644 arch/arm64/boot/dts/socionext/uniphier-nx1-som.dts
create mode 100644 arch/arm64/boot/dts/socionext/uniphier-nx1.dtsi
diff --git a/arch/arm64/boot/dts/socionext/Makefile b/arch/arm64/boot/dts/socionext/Makefile
index 33989a9643ac..0f198888484a 100644
--- a/arch/arm64/boot/dts/socionext/Makefile
+++ b/arch/arm64/boot/dts/socionext/Makefile
@@ -5,6 +5,9 @@ dtb-$(CONFIG_ARCH_UNIPHIER) += \
uniphier-ld20-akebi96.dtb \
uniphier-ld20-global.dtb \
uniphier-ld20-ref.dtb \
+ uniphier-nx1-evb.dtb \
+ uniphier-nx1-ref.dtb \
+ uniphier-nx1-som.dtb \
uniphier-pxs3-ref.dtb \
uniphier-pxs3-ref-gadget0.dtb \
uniphier-pxs3-ref-gadget1.dtb
diff --git a/arch/arm64/boot/dts/socionext/uniphier-nx1-evb.dts b/arch/arm64/boot/dts/socionext/uniphier-nx1-evb.dts
new file mode 100644
index 000000000000..381ec274d78f
--- /dev/null
+++ b/arch/arm64/boot/dts/socionext/uniphier-nx1-evb.dts
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+//
+// Device Tree Source for UniPhier NX1 Evaluation Board
+//
+// Copyright (C) 2021 Socionext Inc.
+// Author: Kunihiko Hayashi <hayashi.kunihiko at socionext.com>
+
+/dts-v1/;
+#include "uniphier-nx1.dtsi"
+
+/ {
+ model = "UniPhier NX1 Evaluation Board";
+ compatible = "socionext,uniphier-nx1-evb", "socionext,uniphier-nx1";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ serial3 = &serial3;
+ spi0 = &spi0;
+ ethernet = ð
+ };
+
+ memory at 20000000 {
+ device_type = "memory";
+ reg = <0 0x20000000 1 0x00000000>;
+ };
+};
+
+&refclk {
+ clock-frequency = <25000000>;
+};
+
+&serial0 {
+ status = "okay";
+};
+
+&serial1 {
+ status = "okay";
+};
+
+&serial2 {
+ status = "okay";
+};
+
+&serial3 {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+};
+
+ð {
+ status = "okay";
+ phy-handle = <ðphy>;
+};
+
+&mdio {
+ ethphy: ethphy at 0 {
+ reg = <0>;
+ };
+};
+
+&usb {
+ status = "okay";
+};
+
+&pcie {
+ status = "okay";
+};
+
+&sd {
+ status = "okay";
+};
+
+&pinctrl_sd {
+ sd {
+ pins = "SDCLK", "SDCMD", "SDDAT0",
+ "SDDAT1", "SDDAT2", "SDDAT3";
+ bias-pull-up;
+ };
+};
diff --git a/arch/arm64/boot/dts/socionext/uniphier-nx1-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-nx1-ref.dts
new file mode 100644
index 000000000000..7c373eba7a81
--- /dev/null
+++ b/arch/arm64/boot/dts/socionext/uniphier-nx1-ref.dts
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+//
+// Device Tree Source for UniPhier NX1 Reference Board
+//
+// Copyright (C) 2021 Socionext Inc.
+// Author: Kunihiko Hayashi <hayashi.kunihiko at socionext.com>
+
+/dts-v1/;
+#include "uniphier-nx1-som.dts"
+
+/ {
+ model = "UniPhier NX1 Reference Board";
+ compatible = "socionext,uniphier-nx1-ref", "socionext,uniphier-nx1";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ i2c3 = &i2c3;
+ spi0 = &spi0;
+ spi1 = &spi1;
+ ethernet = ð
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led0 {
+ label = "user0";
+ gpios = <&pca9536 0 GPIO_ACTIVE_LOW>;
+ };
+
+ led1 {
+ label = "user1";
+ gpios = <&pca9536 1 GPIO_ACTIVE_LOW>;
+ };
+
+ led2 {
+ label = "user2";
+ gpios = <&pca9536 2 GPIO_ACTIVE_LOW>;
+ };
+
+ led3 {
+ label = "user3";
+ gpios = <&pca9536 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+};
+
+&serial1 {
+ status = "okay";
+};
+
+&serial2 {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+};
+
+&spi1 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ pca9536: gpio at 41 {
+ compatible = "ti,pca9536";
+ reg = <0x41>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c3 {
+ status = "okay";
+};
+
+ð {
+ status = "okay";
+ phy-handle = <ðphy>;
+};
+
+&mdio {
+ ethphy: ethernet-phy at 0 {
+ reg = <0>;
+ };
+};
+
+&usb {
+ status = "okay";
+};
+
+&pcie_ep {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/socionext/uniphier-nx1-som.dts b/arch/arm64/boot/dts/socionext/uniphier-nx1-som.dts
new file mode 100644
index 000000000000..e55e482eca6a
--- /dev/null
+++ b/arch/arm64/boot/dts/socionext/uniphier-nx1-som.dts
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+//
+// Device Tree Source for UniPhier NX1 SOM Board
+//
+// Copyright (C) 2021 Socionext Inc.
+// Author: Kunihiko Hayashi <hayashi.kunihiko at socionext.com>
+
+/dts-v1/;
+#include "uniphier-nx1.dtsi"
+
+/ {
+ model = "UniPhier NX1 SOM Board";
+ compatible = "socionext,uniphier-nx1-som", "socionext,uniphier-nx1";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ aliases {
+ serial0 = &serial0;
+ i2c1 = &i2c1;
+ };
+
+ memory at 20000000 {
+ device_type = "memory";
+ reg = <0 0x20000000 1 0x00000000>;
+ };
+};
+
+&refclk {
+ clock-frequency = <25000000>;
+};
+
+&serial0 {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+
+ eeprom at 50 {
+ compatible = "st,24c64", "atmel,24c64";
+ reg = <0x50>;
+ pagesize = <32>;
+ };
+};
+
+&emmc {
+ status = "okay";
+};
+
+&sd {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/socionext/uniphier-nx1.dtsi b/arch/arm64/boot/dts/socionext/uniphier-nx1.dtsi
new file mode 100644
index 000000000000..fe9652b145cc
--- /dev/null
+++ b/arch/arm64/boot/dts/socionext/uniphier-nx1.dtsi
@@ -0,0 +1,702 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+//
+// Device Tree Source for UniPhier NX1 SoC
+//
+// Copyright (C) 2021 Socionext Inc.
+// Author: Kunihiko Hayashi <hayashi.kunihiko at socionext.com>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/gpio/uniphier-gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ compatible = "socionext,uniphier-nx1";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ core2 {
+ cpu = <&cpu2>;
+ };
+ core3 {
+ cpu = <&cpu3>;
+ };
+ };
+ };
+
+ cpu0: cpu at 0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0 0x000>;
+ clocks = <&sys_clk 33>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ operating-points-v2 = <&cluster0_opp>;
+ #cooling-cells = <2>;
+ };
+
+ cpu1: cpu at 1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0 0x001>;
+ clocks = <&sys_clk 33>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ operating-points-v2 = <&cluster0_opp>;
+ #cooling-cells = <2>;
+ };
+
+ cpu2: cpu at 2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0 0x002>;
+ clocks = <&sys_clk 33>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ operating-points-v2 = <&cluster0_opp>;
+ #cooling-cells = <2>;
+ };
+
+ cpu3: cpu at 3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0 0x003>;
+ clocks = <&sys_clk 33>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ operating-points-v2 = <&cluster0_opp>;
+ #cooling-cells = <2>;
+ };
+
+ l2: l2-cache {
+ compatible = "cache";
+ };
+ };
+
+ cluster0_opp: opp-table {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-78125000 {
+ opp-hz = /bits/ 64 <78125000>;
+ clock-latency-ns = <300>;
+ };
+ opp-156250000 {
+ opp-hz = /bits/ 64 <156250000>;
+ clock-latency-ns = <300>;
+ };
+ opp-312500000 {
+ opp-hz = /bits/ 64 <312500000>;
+ clock-latency-ns = <300>;
+ };
+ opp-625000000 {
+ opp-hz = /bits/ 64 <625000000>;
+ clock-latency-ns = <300>;
+ };
+ opp-1250000000 {
+ opp-hz = /bits/ 64 <1250000000>;
+ clock-latency-ns = <300>;
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ clocks {
+ refclk: clock-ref {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-output-names = "ref";
+ };
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio UNIPHIER_GPIO_PORT(3, 0) GPIO_ACTIVE_LOW>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ thermal-zones {
+ cpu-thermal {
+ polling-delay-passive = <250>; /* 250ms */
+ polling-delay = <1000>; /* 1000ms */
+ thermal-sensors = <&pvtctl>;
+
+ trips {
+ cpu_crit: cpu-crit {
+ temperature = <120000>; /* 120C */
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ cpu_alert: cpu-alert {
+ temperature = <110000>; /* 110C */
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ secure-memory at 21000000 {
+ reg = <0x0 0x21000000 0x0 0x01000000>;
+ no-map;
+ };
+ };
+
+ soc at 0 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0 0xffffffff>;
+
+ sysctrl: syscon at 11840000 {
+ compatible = "socionext,uniphier-nx1-sysctrl",
+ "simple-mfd", "syscon";
+ reg = <0x11840000 0x10000>;
+
+ sys_clk: clock-controller {
+ compatible = "socionext,uniphier-nx1-clock";
+ #clock-cells = <1>;
+ };
+
+ sys_rst: reset-controller {
+ compatible = "socionext,uniphier-nx1-reset";
+ #reset-cells = <1>;
+ };
+
+ watchdog {
+ compatible = "socionext,uniphier-wdt";
+ };
+
+ pvtctl: thermal-sensor {
+ compatible = "socionext,uniphier-nx1-thermal";
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ #thermal-sensor-cells = <0>;
+ socionext,tmod-calibration = <0x0f22 0x68ee>;
+ };
+ };
+
+ spi0: spi at 14006000 {
+ compatible = "socionext,uniphier-scssi";
+ reg = <0x14006000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi0>;
+ clocks = <&peri_clk 11>;
+ resets = <&peri_rst 11>;
+ status = "disabled";
+ };
+
+ spi1: spi at 14006100 {
+ compatible = "socionext,uniphier-scssi";
+ reg = <0x14006100 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1>;
+ clocks = <&peri_clk 12>;
+ resets = <&peri_rst 12>;
+ status = "disabled";
+ };
+
+ serial0: serial at 14006800 {
+ compatible = "socionext,uniphier-uart";
+ reg = <0x14006800 0x40>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0>;
+ clocks = <&peri_clk 0>;
+ resets = <&peri_rst 0>;
+ status = "disabled";
+ };
+
+ serial1: serial at 14006900 {
+ compatible = "socionext,uniphier-uart";
+ reg = <0x14006900 0x40>;
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ clocks = <&peri_clk 1>;
+ resets = <&peri_rst 1>;
+ status = "disabled";
+ };
+
+ serial2: serial at 14006a00 {
+ compatible = "socionext,uniphier-uart";
+ reg = <0x14006a00 0x40>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ clocks = <&peri_clk 2>;
+ resets = <&peri_rst 2>;
+ status = "disabled";
+ };
+
+ serial3: serial at 14006b00 {
+ compatible = "socionext,uniphier-uart";
+ reg = <0x14006b00 0x40>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ clocks = <&peri_clk 3>;
+ resets = <&peri_rst 3>;
+ status = "disabled";
+ };
+
+ gpio: gpio at 14007000 {
+ compatible = "socionext,uniphier-gpio";
+ reg = <0x14007000 0x200>;
+ interrupt-parent = <&aidet>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pinctrl 0 0 0>,
+ <&pinctrl 49 0 0>,
+ <&pinctrl 53 0 0>,
+ <&pinctrl 96 0 0>,
+ <&pinctrl 120 0 0>;
+ gpio-ranges-group-names = "gpio_range0",
+ "gpio_range1",
+ "gpio_range2",
+ "gpio_range3",
+ "gpio_range4";
+ ngpios = <126>;
+ socionext,interrupt-ranges = <0 48 6>;
+ };
+
+ eth: ethernet at 15000000 {
+ compatible = "socionext,uniphier-nx1-ave4";
+ reg = <0x15000000 0x8500>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ether_rgmii>;
+ clock-names = "ether";
+ clocks = <&sys_clk 6>;
+ reset-names = "ether";
+ resets = <&sys_rst 6>;
+ phy-mode = "rgmii-id";
+ local-mac-address = [00 00 00 00 00 00];
+ socionext,syscon-phy-mode = <&soc_glue 0>;
+ status = "disabled";
+
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ usb: usb at 15a00000 {
+ compatible = "snps,dwc3";
+ reg = <0x15a00000 0xcd00>;
+ interrupt-names = "host";
+ interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb1>;
+ clock-names = "ref", "bus_early", "suspend";
+ clocks = <&sys_clk 12>, <&sys_clk 12>, <&sys_clk 12>;
+ resets = <&usb_rst 15>;
+ phy-names = "usb2-phy", "usb3-phy";
+ phys = <&usb_hsphy0>, <&usb_ssphy0>;
+ dr_mode = "host";
+ status = "disabled";
+ };
+
+ usb-controller at 15b00000 {
+ compatible = "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x15b00000 0x400>;
+
+ usb_rst: reset-controller at 0 {
+ compatible = "socionext,uniphier-nx1-usb3-reset";
+ reg = <0x0 0x4>;
+ #reset-cells = <1>;
+ clock-names = "link";
+ clocks = <&sys_clk 12>;
+ reset-names = "link";
+ resets = <&sys_rst 12>;
+ };
+
+ usb_vbus0: regulator at 100 {
+ compatible = "socionext,uniphier-nx1-usb3-regulator";
+ reg = <0x100 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 12>;
+ reset-names = "link";
+ resets = <&sys_rst 12>;
+ };
+
+ usb_vbus1: regulator at 110 {
+ compatible = "socionext,uniphier-nx1-usb3-regulator";
+ reg = <0x110 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 12>;
+ reset-names = "link";
+ resets = <&sys_rst 12>;
+ };
+
+ usb_hsphy0: phy at 200 {
+ compatible = "socionext,uniphier-nx1-usb3-hsphy";
+ reg = <0x200 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy", "phy-ext";
+ clocks = <&sys_clk 12>, <&sys_clk 16>,
+ <&sys_clk 13>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 12>, <&sys_rst 16>;
+ vbus-supply = <&usb_vbus0>;
+ };
+
+ usb_hsphy1: phy at 210 {
+ compatible = "socionext,uniphier-nx1-usb3-hsphy";
+ reg = <0x210 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy", "phy-ext";
+ clocks = <&sys_clk 12>, <&sys_clk 16>,
+ <&sys_clk 13>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 12>, <&sys_rst 16>;
+ vbus-supply = <&usb_vbus1>;
+ };
+
+ usb_ssphy0: phy at 300 {
+ compatible = "socionext,uniphier-nx1-usb3-ssphy";
+ reg = <0x300 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy", "phy-ext";
+ clocks = <&sys_clk 12>, <&sys_clk 17>,
+ <&sys_clk 13>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 12>, <&sys_rst 17>;
+ vbus-supply = <&usb_vbus0>;
+ };
+
+ usb_ssphy1: phy at 310 {
+ compatible = "socionext,uniphier-nx1-usb3-ssphy";
+ reg = <0x310 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy", "phy-ext";
+ clocks = <&sys_clk 12>, <&sys_clk 18>,
+ <&sys_clk 13>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 12>, <&sys_rst 18>;
+ vbus-supply = <&usb_vbus1>;
+ };
+ };
+
+ pcie: pcie at 16000000 {
+ compatible = "socionext,uniphier-pcie";
+ reg-names = "dbi", "link", "config", "atu";
+ reg = <0x16000000 0x1000>, <0x179a0000 0x10000>,
+ <0x0fff0000 0x10000>, <0x16300000 0x1000>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ clocks = <&sys_clk 24>;
+ resets = <&sys_rst 24>;
+ num-lanes = <2>;
+ num-viewport = <1>;
+ bus-range = <0x0 0xff>;
+ device_type = "pci";
+ ranges =
+ /* downstream I/O */
+ <0x81000000 0 0x00000000 0x0ffe0000 0 0x00010000>,
+ /* non-prefetchable memory */
+ <0x82000000 0 0x20000000 0x04200000 0 0x0bde0000>;
+ #interrupt-cells = <1>;
+ interrupt-names = "dma", "msi";
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */
+ <0 0 0 2 &pcie_intc 1>, /* INTB */
+ <0 0 0 3 &pcie_intc 2>, /* INTC */
+ <0 0 0 4 &pcie_intc 3>; /* INTD */
+ phy-names = "pcie-phy";
+ phys = <&pcie_phy>;
+ status = "disabled";
+
+ pcie_intc: legacy-interrupt-controller {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ pcie_ep: pcie-ep at 16000000 {
+ compatible = "socionext,uniphier-nx1-pcie-ep";
+ reg-names = "dbi", "dbi2", "link", "addr_space", "atu";
+ reg = <0x16000000 0x1000>, <0x16100000 0x1000>,
+ <0x179a0000 0x10000>, <0x04200000 0xbe00000>,
+ <0x16300000 0x1000>;
+ clock-names = "link";
+ clocks = <&sys_clk 24>;
+ reset-names = "link";
+ resets = <&sys_rst 24>;
+ num-ib-windows = <16>;
+ num-ob-windows = <16>;
+ num-lanes = <2>;
+ phy-names = "pcie-phy";
+ phys = <&pcie_phy>;
+ status = "disabled";
+ };
+
+ pcie_phy: phy at 179b8000 {
+ compatible = "socionext,uniphier-nx1-pcie-phy";
+ reg = <0x179b8000 0x4000>;
+ #phy-cells = <0>;
+ clock-names = "link";
+ clocks = <&sys_clk 24>;
+ reset-names = "link";
+ resets = <&sys_rst 24>;
+ socionext,syscon = <&sysctrl>;
+ };
+
+ i2c0: i2c at 18780000 {
+ compatible = "socionext,uniphier-fi2c";
+ reg = <0x18780000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0>;
+ clocks = <&peri_clk 4>;
+ resets = <&peri_rst 4>;
+ clock-frequency = <400000>;
+ status = "disabled";
+ };
+
+ i2c1: i2c at 18781000 {
+ compatible = "socionext,uniphier-fi2c";
+ reg = <0x18781000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ clocks = <&peri_clk 5>;
+ resets = <&peri_rst 5>;
+ clock-frequency = <400000>;
+ status = "disabled";
+ };
+
+ i2c2: i2c at 18782000 {
+ compatible = "socionext,uniphier-fi2c";
+ reg = <0x18782000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ clocks = <&peri_clk 6>;
+ resets = <&peri_rst 6>;
+ clock-frequency = <400000>;
+ status = "disabled";
+ };
+
+ i2c3: i2c at 18783000 {
+ compatible = "socionext,uniphier-fi2c";
+ reg = <0x18783000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ clocks = <&peri_clk 7>;
+ resets = <&peri_rst 7>;
+ clock-frequency = <400000>;
+ status = "disabled";
+ };
+
+ i2c4: i2c at 18784000 {
+ compatible = "socionext,uniphier-fi2c";
+ reg = <0x18784000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ clocks = <&peri_clk 8>;
+ resets = <&peri_rst 8>;
+ clock-frequency = <100000>;
+ status = "disabled";
+ };
+
+ i2c5: i2c at 18785000 {
+ compatible = "socionext,uniphier-fi2c";
+ reg = <0x18785000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c5>;
+ clocks = <&peri_clk 9>;
+ resets = <&peri_rst 9>;
+ clock-frequency = <100000>;
+ status = "disabled";
+ };
+
+ i2c6: i2c at 18786000 {
+ compatible = "socionext,uniphier-fi2c";
+ reg = <0x18786000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c6>;
+ clocks = <&peri_clk 10>;
+ resets = <&peri_rst 10>;
+ clock-frequency = <100000>;
+ status = "disabled";
+ };
+
+ syscon at 19810000 {
+ compatible = "socionext,uniphier-nx1-sdctrl",
+ "simple-mfd", "syscon";
+ reg = <0x19810000 0x400>;
+
+ sd_clk: clock-controller {
+ compatible = "socionext,uniphier-nx1-sd-clock";
+ #clock-cells = <1>;
+ };
+
+ sd_rst: reset-controller {
+ compatible = "socionext,uniphier-nx1-sd-reset";
+ #reset-cells = <1>;
+ };
+ };
+
+ syscon at 19820000 {
+ compatible = "socionext,uniphier-nx1-perictrl",
+ "simple-mfd", "syscon";
+ reg = <0x19820000 0x200>;
+
+ peri_clk: clock-controller {
+ compatible = "socionext,uniphier-nx1-peri-clock";
+ #clock-cells = <1>;
+ };
+
+ peri_rst: reset-controller {
+ compatible = "socionext,uniphier-nx1-peri-reset";
+ #reset-cells = <1>;
+ };
+ };
+
+ emmc: mmc at 1a000000 {
+ compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc";
+ reg = <0x1a000000 0x400>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_emmc>;
+ clocks = <&sys_clk 4>;
+ resets = <&sys_rst 4>;
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ mmc-pwrseq = <&emmc_pwrseq>;
+ cdns,phy-input-delay-legacy = <9>;
+ cdns,phy-input-delay-mmc-highspeed = <2>;
+ cdns,phy-input-delay-mmc-ddr = <3>;
+ cdns,phy-dll-delay-sdclk = <21>;
+ cdns,phy-dll-delay-sdclk-hsmmc = <21>;
+ };
+
+ sd: mmc at 1a400000 {
+ compatible = "socionext,uniphier-sd-v3.1.1";
+ reg = <0x1a400000 0x800>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sd>;
+ clocks = <&sd_clk 0>;
+ reset-names = "host";
+ resets = <&sd_rst 0>;
+ bus-width = <4>;
+ cap-sd-highspeed;
+ status = "disabled";
+ };
+
+ soc_glue: syscon at 1f800000 {
+ compatible = "socionext,uniphier-nx1-soc-glue",
+ "simple-mfd", "syscon";
+ reg = <0x1f800000 0x2000>;
+
+ pinctrl: pinctrl {
+ compatible = "socionext,uniphier-nx1-pinctrl";
+ };
+ };
+
+ soc-glue at 1f900000 {
+ compatible = "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1f900000 0x2000>;
+ };
+
+ xdmac: dma-controller at 1fa10000 {
+ compatible = "socionext,uniphier-xdmac";
+ reg = <0x1fa10000 0x5300>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ dma-channels = <16>;
+ #dma-cells = <2>;
+ };
+
+ aidet: interrupt-controller at 1fb20000 {
+ compatible = "socionext,uniphier-nx1-aidet";
+ reg = <0x1fb20000 0x200>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gic: interrupt-controller at 1fd00000 {
+ compatible = "arm,gic-v3";
+ reg = <0x1fd00000 0x10000>, /* GICD */
+ <0x1fd80000 0x80000>; /* GICR */
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+};
+
+#include "uniphier-pinctrl.dtsi"
--
2.25.1
More information about the linux-arm-kernel
mailing list