[PATCH 4/9] ARM: dts: suniv: f1c100s: add I2C DT nodes

[Andre Przywara]

On Sun, 06 Nov 2022 09:09:17 +0100
Jernej Škrabec <jernej.skrabec at gmail.com> wrote:

> Dne torek, 01. november 2022 ob 15:16:53 CET je Andre Przywara napisal(a):
> > The Allwinner F1C100s series of SoCs contain three I2C controllers
> > compatible to the ones used in other Allwinner SoCs.
> > 
> > Add the DT nodes describing the resources of the controllers.
> > I2C1 has only one possible pinmux, so add the pinctrl properties for
> > that already.
> > At least one board connects an on-board I2C chip to PD0/PD12 (I2C0), so
> > include those pins already, to simplify referencing them later.
> > 
> > Signed-off-by: Andre Przywara <andre.przywara at arm.com>
> > ---
> >  arch/arm/boot/dts/suniv-f1c100s.dtsi | 50 ++++++++++++++++++++++++++++
> >  1 file changed, 50 insertions(+)
> > 
> > diff --git a/arch/arm/boot/dts/suniv-f1c100s.dtsi
> > b/arch/arm/boot/dts/suniv-f1c100s.dtsi index d5a6324e76465..2901c586971b4
> > 100644
> > --- a/arch/arm/boot/dts/suniv-f1c100s.dtsi
> > +++ b/arch/arm/boot/dts/suniv-f1c100s.dtsi
> > @@ -166,6 +166,18 @@ mmc0_pins: mmc0-pins {
> >  				drive-strength = <30>;
> >  			};
> > 
> > +			/omit-if-no-ref/
> > +			i2c0_pd_pins: i2c0-pd-pins {
> > +				pins = "PD0", "PD12";
> > +				function = "i2c0";
> > +			};
> > +
> > +			/omit-if-no-ref/  
> 
> Above flag is meaningless if i2c1_pins is always referenced by i2c1.

Indeed, good point.

> Anyway, I 
> see in pinctrl driver that there are actually two possible pin assignments for 
> i2c1. One on port D and another on port B.

Ah, those are the pins that are not documented in the manual (which is
where I looked at). I will drop that node.

Cheers,
Andre

> 
> Best regards,
> Jernej
> 
> > +			i2c1_pins: i2c1-pins {
> > +				pins = "PD5", "PD6";
> > +				function = "i2c1";
> > +			};
> > +
> >  			spi0_pc_pins: spi0-pc-pins {
> >  				pins = "PC0", "PC1", "PC2",   
> "PC3";
> >  				function = "spi0";
> > @@ -177,6 +189,44 @@ uart0_pe_pins: uart0-pe-pins {
> >  			};
> >  		};
> > 
> > +		i2c0: i2c at 1c27000 {
> > +			compatible = "allwinner,suniv-f1c100s-i2c",
> > +				     "allwinner,sun6i-a31-i2c";
> > +			reg = <0x01c27000 0x400>;
> > +			interrupts = <7>;
> > +			clocks = <&ccu CLK_BUS_I2C0>;
> > +			resets = <&ccu RST_BUS_I2C0>;
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +			status = "disabled";
> > +		};
> > +
> > +		i2c1: i2c at 1c27400 {
> > +			compatible = "allwinner,suniv-f1c100s-i2c",
> > +				     "allwinner,sun6i-a31-i2c";
> > +			reg = <0x01c27400 0x400>;
> > +			interrupts = <8>;
> > +			clocks = <&ccu CLK_BUS_I2C1>;
> > +			resets = <&ccu RST_BUS_I2C1>;
> > +			pinctrl-names = "default";
> > +			pinctrl-0 = <&i2c1_pins>;
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +			status = "disabled";
> > +		};
> > +
> > +		i2c2: i2c at 1c27800 {
> > +			compatible = "allwinner,suniv-f1c100s-i2c",
> > +				     "allwinner,sun6i-a31-i2c";
> > +			reg = <0x01c27800 0x400>;
> > +			interrupts = <9>;
> > +			clocks = <&ccu CLK_BUS_I2C2>;
> > +			resets = <&ccu RST_BUS_I2C2>;
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +			status = "disabled";
> > +		};
> > +
> >  		timer at 1c20c00 {
> >  			compatible = "allwinner,suniv-f1c100s-  
> timer";
> >  			reg = <0x01c20c00 0x90>;  
> 
> 
> 
> 
>