[PATCH 3/4] arm64: dts: fsd: Add Ethernet support for FSYS0 Block of FSD SoC

Fri Nov 4 05:45:55 PDT 2022

On 04/11/2022 08:05, Sriranjani P wrote:
> The FSD SoC contains two instances of Synopsys DWC QoS Ethernet IP, one
> in FSYS0 block and other in PERIC block.
> 
> Adds device tree node for Ethernet in FSYS0 Block and enables the same for
> FSD platform.
> 
> Cc: Rob Herring <robh+dt at kernel.org>
> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt at linaro.org>
> Cc: Richard Cochran <richardcochran at gmail.com>
> Cc: devicetree at vger.kernel.org
> Signed-off-by: Pankaj Dubey <pankaj.dubey at samsung.com>
> Signed-off-by: Jayati Sahu <jayati.sahu at samsung.com>
> Signed-off-by: Sriranjani P <sriranjani.p at samsung.com>
> ---
>  arch/arm64/boot/dts/tesla/fsd-evb.dts      |  9 ++++
>  arch/arm64/boot/dts/tesla/fsd-pinctrl.dtsi | 56 ++++++++++++++++++++++
>  arch/arm64/boot/dts/tesla/fsd.dtsi         | 38 +++++++++++++++
>  3 files changed, 103 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/tesla/fsd-evb.dts b/arch/arm64/boot/dts/tesla/fsd-evb.dts
> index 1db6ddf03f01..42bf25c680e2 100644
> --- a/arch/arm64/boot/dts/tesla/fsd-evb.dts
> +++ b/arch/arm64/boot/dts/tesla/fsd-evb.dts
> @@ -30,6 +30,15 @@
>  	};
>  };
>  
> +&ethernet_0 {
> +	status = "okay";
> +
> +	fixed-link {
> +		speed=<1000>;

Missing spaces around =.

> +		full-duplex;
> +	};
> +};
> +
>  &fin_pll {
>  	clock-frequency = <24000000>;
>  };
> diff --git a/arch/arm64/boot/dts/tesla/fsd-pinctrl.dtsi b/arch/arm64/boot/dts/tesla/fsd-pinctrl.dtsi
> index d0abb9aa0e9e..8c7e43085a2b 100644
> --- a/arch/arm64/boot/dts/tesla/fsd-pinctrl.dtsi
> +++ b/arch/arm64/boot/dts/tesla/fsd-pinctrl.dtsi
> @@ -64,6 +64,62 @@
>  		samsung,pin-pud = <FSD_PIN_PULL_NONE>;
>  		samsung,pin-drv = <FSD_PIN_DRV_LV2>;
>  	};
> +
> +	eth0_tx_clk: eth0-tx-clk-pins {
> +		samsung,pins = "gpf0-0";
> +		samsung,pin-function = <FSD_PIN_FUNC_2>;
> +		samsung,pin-pud = <FSD_PIN_PULL_DOWN>;
> +		samsung,pin-drv = <FSD_PIN_DRV_LV6>;
> +	};
> +
> +	eth0_tx_data: eth0-tx-data-pins {
> +		samsung,pins = "gpf0-1", "gpf0-2", "gpf0-3", "gpf0-4";
> +		samsung,pin-function = <FSD_PIN_FUNC_2>;
> +		samsung,pin-pud = <FSD_PIN_PULL_UP>;
> +		samsung,pin-drv = <FSD_PIN_DRV_LV6>;
> +	};
> +
> +	eth0_tx_ctrl: eth0-tx-ctrl-pins {
> +		samsung,pins = "gpf0-5";
> +		samsung,pin-function = <FSD_PIN_FUNC_2>;
> +		samsung,pin-pud = <FSD_PIN_PULL_UP>;
> +		samsung,pin-drv = <FSD_PIN_DRV_LV6>;
> +	};
> +
> +	eth0_phy_intr: eth0-phy-intr-pins {
> +		samsung,pins = "gpf0-6";
> +		samsung,pin-function = <FSD_PIN_FUNC_2>;
> +		samsung,pin-pud = <FSD_PIN_PULL_NONE>;
> +		samsung,pin-drv = <FSD_PIN_DRV_LV4>;
> +	};
> +
> +	eth0_rx_clk: eth0-rx-clk-pins {
> +		samsung,pins = "gpf1-0";
> +		samsung,pin-function = <FSD_PIN_FUNC_2>;
> +		samsung,pin-pud = <FSD_PIN_PULL_UP>;
> +		samsung,pin-drv = <FSD_PIN_DRV_LV6>;
> +	};
> +
> +	eth0_rx_data: eth0-rx-data-pins {
> +		samsung,pins = "gpf1-1", "gpf1-2", "gpf1-3", "gpf1-4";
> +		samsung,pin-function = <FSD_PIN_FUNC_2>;
> +		samsung,pin-pud = <FSD_PIN_PULL_UP>;
> +		samsung,pin-drv = <FSD_PIN_DRV_LV6>;
> +	};
> +
> +	eth0_rx_ctrl: eth0-rx-ctrl-pins {
> +		samsung,pins = "gpf1-5";
> +		samsung,pin-function = <FSD_PIN_FUNC_2>;
> +		samsung,pin-pud = <FSD_PIN_PULL_UP>;
> +		samsung,pin-drv = <FSD_PIN_DRV_LV6>;
> +	};
> +
> +	eth0_mdio: eth0-mdio-pins {
> +		samsung,pins = "gpf1-6", "gpf1-7";
> +		samsung,pin-function = <FSD_PIN_FUNC_2>;
> +		samsung,pin-pud = <FSD_PIN_PULL_NONE>;
> +		samsung,pin-drv = <FSD_PIN_DRV_LV4>;
> +	};
>  };
>  
>  &pinctrl_peric {
> diff --git a/arch/arm64/boot/dts/tesla/fsd.dtsi b/arch/arm64/boot/dts/tesla/fsd.dtsi
> index f35bc5a288c2..2495928b71dc 100644
> --- a/arch/arm64/boot/dts/tesla/fsd.dtsi
> +++ b/arch/arm64/boot/dts/tesla/fsd.dtsi
> @@ -32,6 +32,7 @@
>  		spi0 = &spi_0;
>  		spi1 = &spi_1;
>  		spi2 = &spi_2;
> +		eth0 = &ethernet_0;

Not every board will have ethernet, so this should be in board DTS.
However other question is - why do you need it?

>  	};
>  
>  	cpus {
> @@ -860,6 +861,43 @@
>  			clocks = <&clock_fsys0 UFS0_MPHY_REFCLK_IXTAL26>;
>  			clock-names = "ref_clk";
>  		};
> +
> +		ethernet_0: ethernet at 15300000 {
> +			compatible = "tesla,dwc-qos-ethernet-4.21";
> +			reg = <0x0 0x15300000 0x0 0x10000>;
> +			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks =
> +				/* ptp ref clock */

That's not a formatting used in sources. I doubt that they are actually
useful as you copy the name of the clock.

> +				<&clock_fsys0 FSYS0_EQOS_TOP0_IPCLKPORT_CLK_PTP_REF_I>,
> +				/* aclk clocks */
> +				<&clock_fsys0 FSYS0_EQOS_TOP0_IPCLKPORT_ACLK_I>,
> +				/* hclk clocks */
> +				<&clock_fsys0 FSYS0_EQOS_TOP0_IPCLKPORT_HCLK_I>,
> +				/* rgmii clocks */
> +				<&clock_fsys0 FSYS0_EQOS_TOP0_IPCLKPORT_RGMII_CLK_I>,
> +				/* rxi clocks */
> +				<&clock_fsys0 FSYS0_EQOS_TOP0_IPCLKPORT_CLK_RX_I>;
> +			clock-names =
> +				/* ptp ref clocks */
> +				"ptp_ref",
> +				/* aclk clocks */
> +				"master_bus",
> +				/* hclk clocks */
> +				"slave_bus",
> +				/* rgmii clk */
> +				"tx",
> +				/* rxi clocks */
> +				"rx";
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&eth0_tx_clk>, <&eth0_tx_data>, <&eth0_tx_ctrl>,
> +				<&eth0_phy_intr>, <&eth0_rx_clk>, <&eth0_rx_data>,
> +				<&eth0_rx_ctrl>, <&eth0_mdio>;
> +			local-mac-address = [45 54 48 30 4d 43];

So all devices in the world will have exactly the same MAC address? I
don't think that's desired :)

> +			rx-clock-skew = <&sysreg_fsys0 0x0 0x2>;

Where is the property documented?

Does not look like you tested the DTS against bindings. Please run `make
dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
for instructions).

Please confirm that you perform above.

> +			iommus = <&smmu_fsys0 0x0 0x1>;
> +			status = "disabled";

Status is last.

> +			phy-mode = "rgmii";
> +		};
>  	};
>  };
>  

Best regards,
Krzysztof