[PATCH v2 1/1] arm64: dts: imx8mm-tqma8mqml-mba8mx: Fix USB DR

[Alexander Stein]

Using extcon USB host mode works properly on DR interface, e.g.
enabling/disabling VBUS. But USB device mode is not working.
Fix this by switching to usb-role-switch instead.

Fixes: dfcd1b6f7620 ("arm64: dts: freescale: add initial device tree for TQMa8MQML with i.MX8MM")
Signed-off-by: Alexander Stein <alexander.stein at ew.tq-group.com>
---
Changes in v2:
* Improve the commit message describing the actual issue being fixed

 .../dts/freescale/imx8mm-tqma8mqml-mba8mx.dts | 32 +++++++++++++++----
 1 file changed, 26 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
index bfb44630da6b..56323c989d55 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
@@ -34,11 +34,25 @@ reg_usdhc2_vmmc: regulator-vmmc {
 		off-on-delay-us = <12000>;
 	};
 
-	extcon_usbotg1: extcon-usbotg1 {
-		compatible = "linux,extcon-usb-gpio";
+	connector {
+		compatible = "gpio-usb-b-connector", "usb-b-connector";
+		type = "micro";
+		label = "X19";
 		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_usb1_extcon>;
-		id-gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&pinctrl_usb1_connector>;
+		id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port at 0 {
+				reg = <0>;
+				usb_dr_connector: endpoint {
+					remote-endpoint = <&usb1_drd_sw>;
+				};
+			};
+		};
 	};
 };
 
@@ -106,13 +120,19 @@ &usbotg1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbotg1>;
 	dr_mode = "otg";
-	extcon = <&extcon_usbotg1>;
 	srp-disable;
 	hnp-disable;
 	adp-disable;
 	power-active-high;
 	over-current-active-low;
+	usb-role-switch;
 	status = "okay";
+
+	port {
+		usb1_drd_sw: endpoint {
+			remote-endpoint = <&usb_dr_connector>;
+		};
+	};
 };
 
 &usbotg2 {
@@ -242,7 +262,7 @@ pinctrl_usbotg1: usbotg1grp {
 			   <MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC		0x84>;
 	};
 
-	pinctrl_usb1_extcon: usb1-extcongrp {
+	pinctrl_usb1_connector: usb1-connectorgrp {
 		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x1c0>;
 	};
 
-- 
2.34.1