[PATCH v6 2/2] PM / devfreq: mediatek: Introduce MediaTek CCI devfreq driver
Jia-Wei Chang
jia-wei.chang at mediatek.com
Tue May 31 05:25:22 PDT 2022
On Mon, 2022-05-30 at 14:16 +0200, AngeloGioacchino Del Regno wrote:
> Il 27/05/22 13:00, Johnson Wang ha scritto:
> > We introduce a devfreq driver for the MediaTek Cache Coherent
> > Interconnect
> > (CCI) used by some MediaTek SoCs.
> >
> > In this driver, we use the passive devfreq driver to get target
> > frequencies
> > and adjust voltages accordingly. In MT8183 and MT8186, the MediaTek
> > CCI
> > is supplied by the same regulators with the little core CPUs.
> >
> > Signed-off-by: Jia-Wei Chang <jia-wei.chang at mediatek.com>
> > Signed-off-by: Johnson Wang <johnson.wang at mediatek.com>
> > Acked-by: Chanwoo Choi <cw00.choi at samsung.com>
> > ---
> > This patch depends on "devfreq-testing"[1].
> > [1]
> > https://urldefense.com/v3/__https://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux.git/log/?h=devfreq-testing__;!!CTRNKA9wMg0ARbw!2ldxtrMmK2WJP8_r1DcJRm0XQOSZQJfbI5DlNDPEfz84Ble0R7pSP7PbYLreNgVGRyFfDQ$
> >
> > ---
> > drivers/devfreq/Kconfig | 10 +
> > drivers/devfreq/Makefile | 1 +
> > drivers/devfreq/mtk-cci-devfreq.c | 441
> > ++++++++++++++++++++++++++++++
> > 3 files changed, 452 insertions(+)
> > create mode 100644 drivers/devfreq/mtk-cci-devfreq.c
> >
> > diff --git a/drivers/devfreq/Kconfig b/drivers/devfreq/Kconfig
> > index 87eb2b837e68..9754d8b31621 100644
> > --- a/drivers/devfreq/Kconfig
> > +++ b/drivers/devfreq/Kconfig
> > @@ -120,6 +120,16 @@ config ARM_TEGRA_DEVFREQ
> > It reads ACTMON counters of memory controllers and adjusts
> > the
> > operating frequencies and voltages with OPP support.
> >
> > +config ARM_MEDIATEK_CCI_DEVFREQ
> > + tristate "MEDIATEK CCI DEVFREQ Driver"
> > + depends on ARM_MEDIATEK_CPUFREQ || COMPILE_TEST
> > + select DEVFREQ_GOV_PASSIVE
> > + help
> > + This adds a devfreq driver for MediaTek Cache Coherent
> > Interconnect
> > + which is shared the same regulators with the cpu cluster. It
> > can track
> > + buck voltages and update a proper CCI frequency. Use the
> > notification
> > + to get the regulator status.
> > +
> > config ARM_RK3399_DMC_DEVFREQ
> > tristate "ARM RK3399 DMC DEVFREQ Driver"
> > depends on (ARCH_ROCKCHIP && HAVE_ARM_SMCCC) || \
> > diff --git a/drivers/devfreq/Makefile b/drivers/devfreq/Makefile
> > index 0b6be92a25d9..bf40d04928d0 100644
> > --- a/drivers/devfreq/Makefile
> > +++ b/drivers/devfreq/Makefile
> > @@ -11,6 +11,7 @@ obj-$(CONFIG_DEVFREQ_GOV_PASSIVE) +=
> > governor_passive.o
> > obj-$(CONFIG_ARM_EXYNOS_BUS_DEVFREQ) += exynos-bus.o
> > obj-$(CONFIG_ARM_IMX_BUS_DEVFREQ) += imx-bus.o
> > obj-$(CONFIG_ARM_IMX8M_DDRC_DEVFREQ) += imx8m-ddrc.o
> > +obj-$(CONFIG_ARM_MEDIATEK_CCI_DEVFREQ) += mtk-cci-devfreq.o
> > obj-$(CONFIG_ARM_RK3399_DMC_DEVFREQ) += rk3399_dmc.o
> > obj-$(CONFIG_ARM_SUN8I_A33_MBUS_DEVFREQ) += sun8i-a33-mbus.o
> > obj-$(CONFIG_ARM_TEGRA_DEVFREQ) += tegra30-devfreq.o
> > diff --git a/drivers/devfreq/mtk-cci-devfreq.c
> > b/drivers/devfreq/mtk-cci-devfreq.c
> > new file mode 100644
> > index 000000000000..df42da35b312
> > --- /dev/null
> > +++ b/drivers/devfreq/mtk-cci-devfreq.c
> > @@ -0,0 +1,441 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Copyright (C) 2022 MediaTek Inc.
> > + */
> > +
>
> ..snip..
>
> > +};
> > +
> > +static int mtk_ccifreq_probe(struct platform_device *pdev)
> > +{
> > + struct device *dev = &pdev->dev;
> > + struct mtk_ccifreq_drv *drv;
> > + struct devfreq_passive_data *passive_data;
> > + struct dev_pm_opp *opp;
> > + unsigned long rate, opp_volt;
> > + int ret;
> > +
> > + drv = devm_kzalloc(dev, sizeof(*drv), GFP_KERNEL);
> > + if (!drv)
> > + return -ENOMEM;
> > +
> > + drv->dev = dev;
> > + drv->soc_data = (const struct mtk_ccifreq_platform_data *)
> > + of_device_get_match_data(&pdev->dev);
> > + mutex_init(&drv->reg_lock);
> > + platform_set_drvdata(pdev, drv);
> > +
> > + drv->cci_clk = devm_clk_get(dev, "cci");
> > + if (IS_ERR(drv->cci_clk)) {
> > + ret = PTR_ERR(drv->cci_clk);
> > + return dev_err_probe(dev, ret,
> > + "failed to get cci clk: %d\n",
> > ret);
> > + }
> > +
> > + drv->inter_clk = devm_clk_get(dev, "intermediate");
> > + if (IS_ERR(drv->inter_clk)) {
> > + ret = PTR_ERR(drv->inter_clk);
> > + return dev_err_probe(dev, ret,
> > + "failed to get intermediate clk:
> > %d\n", ret);
> > + }
> > +
> > + drv->proc_reg = devm_regulator_get_optional(dev, "proc");
>
> In the devicetree binding for this driver, the "proc" regulator is
> *not* optional,
> but here you're using devm_regulator_get_optional.
>
> If this is not optional, you should use devm_regulator_get() instead.
>
Hi Angelo,
This is similiar case to mediatek-cpufreq.c [1].
Regulator framework has three variants of APIs for getting regulator
handler.
We do NOT choose regulator_get_exclusive() because cpufreq and cci
share with the same power rail.
We choose regulator_get_optional() so that we can handle error if it
returns ERR_PTR(-ENODEV) rather than a dummy handler from
regulator_get().
Please inform me if I get it wrong.
That's what I understand and you can refer to [2].
Thanks.
[1]: 20220408045908.21671-4-rex-bc.chen at mediatek.com
[2]:
https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1327385.html
> > + if (IS_ERR(drv->proc_reg)) {
> > + ret = PTR_ERR(drv->proc_reg);
> > + return dev_err_probe(dev, ret,
> > + "failed to get proc regulator:
> > %d\n", ret);
>
> There's no need to print ret... dev_err_probe() takes care of that
> for you already:
> in this case, you're printing the value of ret twice.
>
> > + }
> > +
> > + ret = regulator_enable(drv->proc_reg);
>
> If you move this call after the devm_regulator_get_optional() call
> for the sram
> vreg, you will be able to use dev_err_probe for the latter as well.
>
> > + if (ret) {
> > + dev_err(dev, "failed to enable proc regulator\n");
>
> Why aren't you using dev_err_probe here, like you've done for the
> other instances?
>
> > + return ret;
> > + }
> > +
> > + drv->sram_reg = devm_regulator_get_optional(dev, "sram");
> > + if (IS_ERR(drv->sram_reg))
> > + drv->sram_reg = NULL;
>
> When you use regulator_get_optional() (including the devm_ variant of
> it), you
> shall return an error, if there's any... that's what the _optional()
> is for.
>
> if (IS_ERR(drv->sram_reg))
> return dev_err_probe(dev, PTR_ERR(drv->proc_reg),
> "failed to get sram regulator");
>
> > + else {
> > + ret = regulator_enable(drv->sram_reg);
> > + if (ret) {
> > + dev_err(dev, "failed to enable sram
> > regulator\n");
> > + goto out_free_resources;
> > + }
> > + }
> > +
>
> Regards,
> Angelo
>
>
More information about the linux-arm-kernel
mailing list