[RESEND PATCH 1/2] Input: mt6779-keypad - fix hardware code mapping

Dmitry Torokhov dmitry.torokhov at gmail.com
Sat May 28 22:23:48 PDT 2022


On Tue, May 24, 2022 at 09:21:28PM +0200, Mattijs Korpershoek wrote:
> On dim., mai 22, 2022 at 22:42, Dmitry Torokhov <dmitry.torokhov at gmail.com> wrote:
> 
> > On Mon, May 16, 2022 at 01:06:43PM +0200, AngeloGioacchino Del Regno wrote:
> >> Il 16/05/22 09:30, Mattijs Korpershoek ha scritto:
> >> > Hi Dmitry,
> >> > 
> >> > Thank you for your review,
> >> > 
> >> > On dim., mai 15, 2022 at 22:23, Dmitry Torokhov <dmitry.torokhov at gmail.com> wrote:
> >> > 
> >> > > On Fri, May 13, 2022 at 05:18:44PM +0200, Mattijs Korpershoek wrote:
> >> > > > In mt6779_keypad_irq_handler(), we
> >> > > > 1. Read a hardware code from KPD_MEM1 -> KPD_MEM5
> >> > > > 2. Use that hardware code to compute columns/rows for the standard
> >> > > >     keyboard matrix.
> >> > > > 
> >> > > > According to the (non-public) datasheet, the
> >> > > > map between the hardware code and the cols/rows is:
> >> > > > 
> >> > > >          |(0)  |(1)  |(2)
> >> > > >      ----*-----*-----*-----
> >> > > >          |     |     |
> >> > > >          |(9)  |(10) |(11)
> >> > > >      ----*-----*-----*-----
> >> > > >          |     |     |
> >> > > >          |(18) |(19) |(20)
> >> > > >      ----*-----*-----*-----
> >> > > >          |     |     |
> >> > > > 
> >> > > > This brings us to another formula:
> >> > > > -> row = code / 9;
> >> > > > -> col = code % 3;
> >> > > 
> >> > > What if there are more than 3 columns?
> >> > That's not supported, in hardware, according to the datasheet.
> >> > 
> >> > The datasheet I have states that "The interface of MT6763 only supports
> >> > 3*3 single or 2*2 double, but internal ASIC still detects keys in the
> >> > manner of 8*8 single, and 3*3 double. The registers and key codes still
> >> > follows the legacy naming".
> >> > 
> >> > Should I add another patch in this series to add that limitation in the
> >> > probe? There are no checks done in the probe() right now.
> >> > 
> >> 
> >> I've just checked a downstream kernel for MT6795 and that one looks like
> >> being fully compatible with this driver as well... and as far as downstream
> >> is concerned, apparently, mt6735, 6739, 6755, 6757, 6758, 6763, 6771, 6775
> >> all have the same register layout and the downstream driver for these is
> >> always the very same one...
> >> 
> >> ...so, I don't think that there's currently any SoC that supports more than
> >> three columns. Besides, a fast check shows that MT8195 also has the same.
> >> At this point, I'd say that assuming that there are 3 columns, nor less, not
> >> more, is just fine.
> >
> > OK, now that I looked at the datasheet I remember how it came about. The
> > programming (register) interface does not really care about how actual
> > matrix is organized, and instead has a set of bits representing keys,
> > from KEY0 to KEY77, arranged in 5 chunks of 15 bits split into 5 32-bit
> > registers. So we simply decided to use register number as row and
> > offset in the register as column when encoding our "matrix".
> 
> That's correct and that's a good way to phrase it.
> I will add that in the commit message.
> 
> >
> > This does not match the actual keypad matrix organization, so if we want
> > to change this, that's fine, but then we also need to recognize that we
> > are skipping bits 16-31, 48-63, and so on, so to get to the right key
> > number we need to do something like:
> >
> > 	key = bit_nr / 32 * 16 + bit_nr % 32;
> > 	row = key / 9;
> > 	col = key % 9;
> 
> I would prefer to have the driver's matrix_keypad (build in probe()) to
> match the actual hardware. To me this seems easier to understand for
> people familiar with the hardware.
> 
> I've also tested the above snippet and it matches my expectations.
> 
> >
> > I looked at the datasheets I have and they talk about 8x8 single keypad
> > matrix, and 3x3 double keypad (with actual matrices either 3x3 or 2x2)
> 
> Indeed. I plan to send out double keypad support for this driver since
> that's actually needed for mt8183-pumpkin as well.
> It's already in our mtk-v5.10[1] integration tree but I have not submitted
> it yet.
> I planned to send this a separate series to avoid burdening / have
> smaller chunks to review. If that was a mistake, please let me know.
> 
> > but I do not actually see this map layout that Mattijs drew  documented
> 
> The map layout that I draw is not directly copied from the datasheet.
> It's a "translation" of the following table:
> 
> | hardware key code | col0 | col1 | col2|
> | ----------------- | -----| ---- | --- |
> | row0              | 0    | 1    | 2   |
> | row1              | 9    | 10   | 11  |
> | row2              | 18   | 19   | 20  |
> 
> It seems that caused more confusion than actual useful information,
> sorry about that.
> 
> > anywhere though...  I also wonder if there are already existing DTSes in
> > the wild that will be rendered invalid by these changes. I wonder if it
> > would not be be better to document the existing meaning of row and
> > column in the driver?
> 
> The concern for "DTSes in the wild" that will break is a valid point.
> I'm not aware of any of those. Most vendor trees i've seen don't use
> this driver at all. I hope that will change at some point.
> 
> In the end. I'd prefer to have the driver's keypad matrix match
> the actual hardware. Right now we can have a 5x32 matrix which seems
> absurd. Having at most an 8x8 is more reasonable.
> 
> I'd like to send v3 with just fixing the row/column suggestion in
> mt6779_keypad_irq_handler() that Dmitry suggested.
> 
> Would that work Dmitry?

OK, let's do that. Although I'd be curious to see the double keypad
patches as according to the datasheets I saw the translation is
different for those.

Thanks.

-- 
Dmitry



More information about the linux-arm-kernel mailing list