[PATCH] dt-bindings: dma: fsl-edma: Convert to DT schema
Krzysztof Kozlowski
krzysztof.kozlowski at linaro.org
Thu May 26 01:01:42 PDT 2022
On 26/05/2022 05:56, Peng Fan (OSS) wrote:
> From: Peng Fan <peng.fan at nxp.com>
>
> Convert the eDMA controller binding to DT schema.
>
> Signed-off-by: Peng Fan <peng.fan at nxp.com>
> ---
> .../devicetree/bindings/dma/fsl,edma.yaml | 136 ++++++++++++++++++
> .../devicetree/bindings/dma/fsl-edma.txt | 111 --------------
> 2 files changed, 136 insertions(+), 111 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/dma/fsl,edma.yaml
> delete mode 100644 Documentation/devicetree/bindings/dma/fsl-edma.txt
>
> diff --git a/Documentation/devicetree/bindings/dma/fsl,edma.yaml b/Documentation/devicetree/bindings/dma/fsl,edma.yaml
> new file mode 100644
> index 000000000000..dbb69aca7d67
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/dma/fsl,edma.yaml
> @@ -0,0 +1,136 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/dma/fsl,edma.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Freescale enhanced Direct Memory Access(eDMA) Controller
> +
> +description: |
> + The eDMA channels have multiplex capability by programmble
programmable
> + memory-mapped registers. channels are split into two groups, called
> + DMAMUX0 and DMAMUX1, specific DMA request source can only be multiplexed
> + by any channel of certain group, DMAMUX0 or DMAMUX1, but not both.
> +
> +maintainers:
> + - Peng Fan <peng.fan at nxp.com>
> +
> +allOf:
> + - $ref: "dma-controller.yaml#"
> +
> +properties:
> + compatible:
> + oneOf:
> + - const: fsl,vf610-edma
> + - const: fsl,imx7ulp-edma
These should be one enum.
> + - items:
> + - const: fsl,ls1028a-edma
> + - const: fsl,vf610-edma
> +
> + "#dma-cells":
> + const: 2
> +
> + dma-channels:
> + minItems: 32
> + maxItems: 64
> +
> + reg:
> + minItems: 2
> + maxItems: 65
Old binding mentions only three regions. Why 65?
> +
> + interrupts:
> + minItems: 2
> + maxItems: 65
The maxItems look weird here. Shouldn't this be 17? This needs its own
constraints in allOf:if:then per variant.
> +
> + clocks:
> + maxItems: 2
> +
> + big-endian:
> + description: |
> + If present registers and hardware scatter/gather descriptors of the
> + eDMA are implemented in big endian mode, otherwise in little mode.
> + type: boolean
> +
> + interrupt-names:
> + items:
> + - const: edma-tx
> + - const: edma-err
Put it next to interrupts.
> +
> +required:
> + - "#dma-cells"
> + - compatible
> + - reg
> + - interrupts
> + - clocks
> + - dma-channels
> +
> +if:
This should be under allOf and that entire allOf block (with $ref)
should be located here.
> + properties:
> + compatible:
> + contains:
> + const: fsl,imx7ulp-edma
> +then:
> + properties:
> + clock-names:
> + items:
> + - const: dma
> + - const: dmamux0
> +else:
> + properties:
> + clock-names:
> + items:
> + - const: dmamux0
> + - const: dmamux1
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/clock/vf610-clock.h>
> +
> + edma0: dma-controller at 40018000 {
> + #dma-cells = <2>;
> + compatible = "fsl,vf610-edma";
> + reg = <0x40018000 0x2000>,
> + <0x40024000 0x1000>,
> + <0x40025000 0x1000>;
> + interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>,
> + <0 9 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "edma-tx", "edma-err";
> + dma-channels = <32>;
> + clock-names = "dmamux0", "dmamux1";
> + clocks = <&clks VF610_CLK_DMAMUX0>, <&clks VF610_CLK_DMAMUX1>;
> + };
> +
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/clock/imx7ulp-clock.h>
> +
> + edma1: dma-controller at 40080000 {
> + #dma-cells = <2>;
> + compatible = "fsl,imx7ulp-edma";
> + reg = <0x40080000 0x2000>,
> + <0x40210000 0x1000>;
> + dma-channels = <32>;
> + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
> + /* last is eDMA2-ERR interrupt */
> + <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "dma", "dmamux0";
> + clocks = <&pcc2 IMX7ULP_CLK_DMA1>, <&pcc2 IMX7ULP_CLK_DMA_MUX1>;
> + };
> diff --git a/Documentation/devicetree/bindings/dma/fsl-edma.txt b/Documentation/devicetree/bindings/dma/fsl-edma.txt
> deleted file mode 100644
> index ee1754739b4b..000000000000
> --- a/Documentation/devicetree/bindings/dma/fsl-edma.txt
> +++ /dev/null
> @@ -1,111 +0,0 @@
> -* Freescale enhanced Direct Memory Access(eDMA) Controller
> -
> - The eDMA channels have multiplex capability by programmble memory-mapped
> -registers. channels are split into two groups, called DMAMUX0 and DMAMUX1,
> -specific DMA request source can only be multiplexed by any channel of certain
> -group, DMAMUX0 or DMAMUX1, but not both.
> -
> -* eDMA Controller
> -Required properties:
> -- compatible :
> - - "fsl,vf610-edma" for eDMA used similar to that on Vybrid vf610 SoC
> - - "fsl,imx7ulp-edma" for eDMA2 used similar to that on i.mx7ulp
> - - "fsl,ls1028a-edma" followed by "fsl,vf610-edma" for eDMA used on the
> - LS1028A SoC.
> -- reg : Specifies base physical address(s) and size of the eDMA registers.
> - The 1st region is eDMA control register's address and size.
> - The 2nd and the 3rd regions are programmable channel multiplexing
> - control register's address and size.
> -- interrupts : A list of interrupt-specifiers, one for each entry in
> - interrupt-names on vf610 similar SoC. But for i.mx7ulp per channel
> - per transmission interrupt, total 16 channel interrupt and 1
> - error interrupt(located in the last), no interrupt-names list on
> - i.mx7ulp for clean on dts.
> -- #dma-cells : Must be <2>.
> - The 1st cell specifies the DMAMUX(0 for DMAMUX0 and 1 for DMAMUX1).
> - Specific request source can only be multiplexed by specific channels
> - group called DMAMUX.
> - The 2nd cell specifies the request source(slot) ID.
> - See the SoC's reference manual for all the supported request sources.
> -- dma-channels : Number of channels supported by the controller
> -- clock-names : A list of channel group clock names. Should contain:
> - "dmamux0" - clock name of mux0 group
> - "dmamux1" - clock name of mux1 group
> - Note: No dmamux0 on i.mx7ulp, but another 'dma' clk added on i.mx7ulp.
> -- clocks : A list of phandle and clock-specifier pairs, one for each entry in
> - clock-names.
> -
> -Optional properties:
> -- big-endian: If present registers and hardware scatter/gather descriptors
> - of the eDMA are implemented in big endian mode, otherwise in little
> - mode.
> -- interrupt-names : Should contain the below on vf610 similar SoC but not used
> - on i.mx7ulp similar SoC:
> - "edma-tx" - the transmission interrupt
> - "edma-err" - the error interrupt
> -
> -
> -Examples:
> -
> -edma0: dma-controller at 40018000 {
> - #dma-cells = <2>;
> - compatible = "fsl,vf610-edma";
> - reg = <0x40018000 0x2000>,
> - <0x40024000 0x1000>,
> - <0x40025000 0x1000>;
> - interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>,
> - <0 9 IRQ_TYPE_LEVEL_HIGH>;
> - interrupt-names = "edma-tx", "edma-err";
> - dma-channels = <32>;
> - clock-names = "dmamux0", "dmamux1";
> - clocks = <&clks VF610_CLK_DMAMUX0>,
> - <&clks VF610_CLK_DMAMUX1>;
> -}; /* vf610 */
> -
> -edma1: dma-controller at 40080000 {
> - #dma-cells = <2>;
> - compatible = "fsl,imx7ulp-edma";
> - reg = <0x40080000 0x2000>,
> - <0x40210000 0x1000>;
> - dma-channels = <32>;
> - interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
> - /* last is eDMA2-ERR interrupt */
> - <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
> - clock-names = "dma", "dmamux0";
> - clocks = <&pcc2 IMX7ULP_CLK_DMA1>,
> - <&pcc2 IMX7ULP_CLK_DMA_MUX1>;
> -}; /* i.mx7ulp */
> -
> -* DMA clients
> -DMA client drivers that uses the DMA function must use the format described
> -in the dma.txt file, using a two-cell specifier for each channel: the 1st
> -specifies the channel group(DMAMUX) in which this request can be multiplexed,
> -and the 2nd specifies the request source.
> -
> -Examples:
> -
> -sai2: sai at 40031000 {
> - compatible = "fsl,vf610-sai";
> - reg = <0x40031000 0x1000>;
> - interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
> - clock-names = "sai";
> - clocks = <&clks VF610_CLK_SAI2>;
> - dma-names = "tx", "rx";
> - dmas = <&edma0 0 21>,
> - <&edma0 0 20>;
> -};
Best regards,
Krzysztof
More information about the linux-arm-kernel
mailing list