[PATCH v4 2/2] ARM: dts: bananapi-m2-ultra: Enable USB0_OTG and HOST support

[qianfanguijin at 163.com]

From: qianfan Zhao <qianfanguijin at 163.com>

let USB0 work at OTG mode.

Signed-off-by: qianfan Zhao <qianfanguijin at 163.com>
---
 .../boot/dts/sun8i-r40-bananapi-m2-ultra.dts  | 39 +++++++++++++++++++
 1 file changed, 39 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
index 28197bbcb1d5..b3421e67967d 100644
--- a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
+++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
@@ -122,6 +122,10 @@ &de {
 	status = "okay";
 };
 
+&ehci0 {
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
@@ -164,6 +168,7 @@ axp22x: pmic at 34 {
 		reg = <0x34>;
 		interrupt-parent = <&nmi_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		x-powers,drive-vbus-en;
 	};
 };
 
@@ -199,6 +204,10 @@ &mmc2 {
 	status = "okay";
 };
 
+&ohci0 {
+	status = "okay";
+};
+
 &ohci1 {
 	status = "okay";
 };
@@ -216,6 +225,15 @@ &pio {
 	vcc-pe-supply = <&reg_eldo1>;
 	vcc-pf-supply = <&reg_dcdc1>;
 	vcc-pg-supply = <&reg_dldo1>;
+
+	/* USB0_DRVVBUS connected to both the PMIC.N_VBUSEN and PI13,
+	 * we chose PMIC.N_VBUSEN for control, so set the gpio as
+	 * input mode here.
+	 */
+	usb0_vbus_enable_gpio: usb0-vbus-enable-gpio {
+		pins = "PI13";
+		function = "gpio_in";
+	};
 };
 
 &reg_aldo2 {
@@ -298,6 +316,11 @@ &reg_dldo4 {
 	regulator-name = "vdd2v5-sata";
 };
 
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
+	status = "okay";
+};
+
 &reg_eldo3 {
 	regulator-min-microvolt = <1200000>;
 	regulator-max-microvolt = <1200000>;
@@ -333,7 +356,23 @@ bluetooth {
 	};
 };
 
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
 &usbphy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_vbus_enable_gpio>;
+
+	usb0_id_det-gpios = <&pio 8 4 GPIO_ACTIVE_HIGH>; /* PI4 */
+	usb0_vbus_det-gpios = <&pio 8 8 GPIO_ACTIVE_HIGH>; /* PI8 */
+	usb0_vbus_power-supply = <&usb_power_supply>;
+	usb0_vbus-supply = <&reg_drivevbus>;
 	usb1_vbus-supply = <&reg_vcc5v0>;
 	usb2_vbus-supply = <&reg_vcc5v0>;
 	status = "okay";
-- 
2.25.1