[PATCH v2 11/24] ARM: dts: imx7-colibri: clean-up usdhc1 and add sleep config

Marcel Ziswiler marcel at ziswiler.com
Mon May 16 06:47:21 PDT 2022


From: Marcel Ziswiler <marcel.ziswiler at toradex.com>

Adding no-1-8-v property to usdhc1 to disable +1.8V signaling (UHS-I)
mode on SoM dtsi level.

Clean up no-1-8-v from Aster carrier board dtsi, which is using defaults
from SoM dtsi and is not UHS-I capable.

A carrier board may have a MMC/SD card slot with a switchable power
supply. Add a pinctrl sleep used when the card power is off to avoid
backfeeding to the card and add the "sleep" pinctrl to the usdhc1
controller.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler at toradex.com>
---

(no changes since v1)

 arch/arm/boot/dts/imx7-colibri-aster.dtsi   |  5 +-
 arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi |  3 -
 arch/arm/boot/dts/imx7-colibri.dtsi         | 75 ++++++++++++++-------
 3 files changed, 51 insertions(+), 32 deletions(-)

diff --git a/arch/arm/boot/dts/imx7-colibri-aster.dtsi b/arch/arm/boot/dts/imx7-colibri-aster.dtsi
index 440f98dc323d..f3a5cb7d6a0c 100644
--- a/arch/arm/boot/dts/imx7-colibri-aster.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri-aster.dtsi
@@ -61,10 +61,7 @@ &usbotg1 {
 	status = "okay";
 };
 
+/* Colibri MMC/SD */
 &usdhc1 {
-	keep-power-in-suspend;
-	no-1-8-v;
-	wakeup-source;
-	vmmc-supply = <&reg_3v3>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
index 33a9cbbca0d2..618831e89ce8 100644
--- a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
@@ -97,8 +97,5 @@ &usbotg1 {
 };
 
 &usdhc1 {
-	keep-power-in-suspend;
-	wakeup-source;
-	vmmc-supply = <&reg_3v3>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
index 09dbd262dad1..3da9ddc06aae 100644
--- a/arch/arm/boot/dts/imx7-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri.dtsi
@@ -585,12 +585,19 @@ &usbotg1 {
 	extcon = <0>, <&extcon_usbc_det>;
 };
 
+/* Colibri MMC/SD */
 &usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_cd_usdhc1>;
 	cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
 	disable-wp;
+	no-1-8-v;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_cd_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_cd_usdhc1>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_cd_usdhc1>;
+	pinctrl-3 = <&pinctrl_usdhc1_sleep &pinctrl_cd_usdhc1_sleep>;
+	vmmc-supply = <&reg_3v3>;
 	vqmmc-supply = <&reg_LDO2>;
+	wakeup-source;
 };
 
 &usdhc3 {
@@ -949,36 +956,48 @@ MX7D_PAD_UART3_CTS_B__GPIO4_IO7	0x14 /* SODIMM 129 USBH PEN */
 		>;
 	};
 
-	pinctrl_usdhc1: usdhc1-grp {
+	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
-			MX7D_PAD_SD1_CMD__SD1_CMD	0x59
-			MX7D_PAD_SD1_CLK__SD1_CLK	0x19
-			MX7D_PAD_SD1_DATA0__SD1_DATA0	0x59
-			MX7D_PAD_SD1_DATA1__SD1_DATA1	0x59
-			MX7D_PAD_SD1_DATA2__SD1_DATA2	0x59
-			MX7D_PAD_SD1_DATA3__SD1_DATA3	0x59
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x19 /* SODIMM 47 */
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x59 /* SODIMM 190 */
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x59 /* SODIMM 192 */
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x59 /* SODIMM 49 */
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x59 /* SODIMM 51 */
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x59 /* SODIMM 53 */
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
 		fsl,pins = <
-			MX7D_PAD_SD1_CMD__SD1_CMD	0x5a
-			MX7D_PAD_SD1_CLK__SD1_CLK	0x1a
-			MX7D_PAD_SD1_DATA0__SD1_DATA0	0x5a
-			MX7D_PAD_SD1_DATA1__SD1_DATA1	0x5a
-			MX7D_PAD_SD1_DATA2__SD1_DATA2	0x5a
-			MX7D_PAD_SD1_DATA3__SD1_DATA3	0x5a
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x1a
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x5a
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5a
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5a
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5a
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5a
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
 		fsl,pins = <
-			MX7D_PAD_SD1_CMD__SD1_CMD	0x5b
-			MX7D_PAD_SD1_CLK__SD1_CLK	0x1b
-			MX7D_PAD_SD1_DATA0__SD1_DATA0	0x5b
-			MX7D_PAD_SD1_DATA1__SD1_DATA1	0x5b
-			MX7D_PAD_SD1_DATA2__SD1_DATA2	0x5b
-			MX7D_PAD_SD1_DATA3__SD1_DATA3	0x5b
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x1b
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x5b
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5b
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5b
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5b
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5b
+		>;
+	};
+
+	/* Avoid backfeeding with removed card power. */
+	pinctrl_usdhc1_sleep: usdhc1-slpgrp {
+		fsl,pins = <
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x10
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x10
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x10
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x10
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x10
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x10
 		>;
 	};
 
@@ -1077,9 +1096,15 @@ MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5	0x4000007f
 		>;
 	};
 
-	pinctrl_cd_usdhc1: usdhc1-cd-grp {
+	pinctrl_cd_usdhc1: cdusdhc1grp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO00__GPIO1_IO0	0x59 /* SODIMM 43 / MMC_CD */
+		>;
+	};
+
+	pinctrl_cd_usdhc1_sleep: cdusdhc1-slpgrp {
 		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO00__GPIO1_IO0	0x59 /* CD */
+			MX7D_PAD_LPSR_GPIO1_IO00__GPIO1_IO0	0x0
 		>;
 	};
 
-- 
2.35.1




More information about the linux-arm-kernel mailing list