[RFC v8 net-next 00/16] add support for VSC7512 control over SPI
Colin Foster
colin.foster at in-advantage.com
Sun May 8 11:52:57 PDT 2022
The patch set in general is to add support for the VSC7512, and
eventually the VSC7511, VSC7513 and VSC7514 devices controlled over
SPI. The driver is believed to be fully functional for the internal
phy ports (0-3) on the VSC7512. It is not yet functional for SGMII,
QSGMII, and SerDes ports.
I have mentioned previously:
The hardware setup I'm using for development is a beaglebone black, with
jumpers from SPI0 to the microchip VSC7512 dev board. The microchip dev
board has been modified to not boot from flash, but wait for SPI. An
ethernet cable is connected from the beaglebone ethernet to port 0 of
the dev board.
The relevant sections of the device tree I'm using for the VSC7512 is
below. Notably the SGPIO LEDs follow link status and speed from network
triggers.
In order to make this work, I have modified the cpsw driver, and now the
cpsw_new driver, to allow for frames over 1500 bytes. Otherwise the
tagging protocol will not work between the beaglebone and the VSC7512. I
plan to eventually try to get those changes in mainline, but I don't
want to get distracted from my initial goal. I also had to change
bonecommon.dtsi to avoid using VLAN 0.
I believe much of the MFD sections are very near feature-complete,
whereas the switch section will require ongoing work to enable
additional ports / features. This could lead to a couple potential
scenarios:
The first being patches 1-8 being split into a separate patch set, while
patches 9-16 remain in the RFC state. This would offer the pinctrl /
sgpio / mdio controller functionality, but no switch control until it is
ready.
The second would assume the current state of the switch driver is
acceptable (or at least very near so) and the current patch set gets an
official PATCH set (with minor changes as necessary - e.g. squashing
patch 16 into 14). That might be ambitious.
The third would be to keep this patch set in RFC until switch
functionality is more complete. I'd understand if this was the desired
path... but it would mean me having to bug more reviewers.
/ {
vscleds {
compatible = "gpio-leds";
vscled at 0 {
label = "port0led";
gpios = <&sgpio_out1 0 0 GPIO_ACTIVE_LOW>;
default-state = "off";
linux,default-trigger = "ocelot-miim0.2.auto-mii:00:link";
};
vscled at 1 {
label = "port0led1";
gpios = <&sgpio_out1 0 1 GPIO_ACTIVE_LOW>;
default-state = "off";
linux,default-trigger = "ocelot-miim0.2.auto-mii:00:1Gbps";
};
[ ... ]
};
};
&spi0 {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
ocelot-chip at 0 {
compatible = "mscc,vsc7512_mfd_spi";
spi-max-frequency = <2500000>;
reg = <0>;
ethernet-switch at 0 {
compatible = "mscc,vsc7512-ext-switch";
ports {
#address-cells = <1>;
#size-cells = <0>;
port at 0 {
reg = <0>;
label = "cpu";
status = "okay";
ethernet = <&mac_sw>;
phy-handle = <&sw_phy0>;
phy-mode = "internal";
};
port at 1 {
reg = <1>;
label = "swp1";
status = "okay";
phy-handle = <&sw_phy1>;
phy-mode = "internal";
};
};
};
mdio0: mdio0 at 0 {
compatible = "mscc,ocelot-miim";
#address-cells = <1>;
#size-cells = <0>;
sw_phy0: ethernet-phy at 0 {
reg = <0x0>;
};
sw_phy1: ethernet-phy at 1 {
reg = <0x1>;
};
sw_phy2: ethernet-phy at 2 {
reg = <0x2>;
};
sw_phy3: ethernet-phy at 3 {
reg = <0x3>;
};
};
mdio1: mdio1 at 1 {
compatible = "mscc,ocelot-miim";
pinctrl-names = "default";
pinctrl-0 = <&miim1>;
#address-cells = <1>;
#size-cells = <0>;
sw_phy4: ethernet-phy at 4 {
reg = <0x4>;
};
sw_phy5: ethernet-phy at 5 {
reg = <0x5>;
};
sw_phy6: ethernet-phy at 6 {
reg = <0x6>;
};
sw_phy7: ethernet-phy at 7 {
reg = <0x7>;
};
};
gpio: pinctrl at 0 {
compatible = "mscc,ocelot-pinctrl";
gpio-controller;
#gpio_cells = <2>;
gpio-ranges = <&gpio 0 0 22>;
led_shift_reg_pins: led-shift-reg-pins {
pins = "GPIO_0", "GPIO_1", "GPIO_2", "GPIO_3";
function = "sg0";
};
miim1: miim1 {
pins = "GPIO_14", "GPIO_15";
function = "miim";
};
};
sgpio: sgpio {
compatible = "mscc,ocelot-sgpio";
#address-cells = <1>;
#size-cells = <0>;
bus-frequency=<12500000>;
clocks = <&ocelot_clock>;
microchip,sgpio-port-ranges = <0 15>;
pinctrl-names = "default";
pinctrl-0 = <&led_shift_reg_pins>;
sgpio_in0: sgpio at 0 {
compatible = "microchip,sparx5-sgpio-bank";
reg = <0>;
gpio-controller;
#gpio-cells = <3>;
ngpios = <64>;
};
sgpio_out1: sgpio at 1 {
compatible = "microchip,sparx5-sgpio-bank";
reg = <1>;
gpio-controller;
#gpio-cells = <3>;
ngpios = <64>;
};
};
};
};
And I'll include the relevant dmesg prints - I don't love the "invalid
resource" prints, as they seem to be misleading. They're a byproduct of
looking for IO resources before falling back to REG.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.18.0-rc5-01295-g47053e327c52 (X at X) (arm-linux-gnueabi-gcc (Ubuntu 9.4.0-1ubuntu1~20.04.1) 9.4.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #630 SMP PREEMPT Sun May 8 10:56:51 PDT 2022
...
[ 2.829319] pinctrl-ocelot ocelot-pinctrl.0.auto: DMA mask not set
[ 2.835718] pinctrl-ocelot ocelot-pinctrl.0.auto: invalid resource
[ 2.842717] gpiochip_find_base: found new base at 2026
[ 2.842774] gpio gpiochip4: (ocelot-gpio): created GPIO range 0->21 ==> ocelot-pinctrl.0.auto PIN 0->21
[ 2.845693] gpio gpiochip4: (ocelot-gpio): added GPIO chardev (254:4)
[ 2.845828] gpio gpiochip4: registered GPIOs 2026 to 2047 on ocelot-gpio
[ 2.845855] pinctrl-ocelot ocelot-pinctrl.0.auto: driver registered
[ 2.855925] pinctrl-microchip-sgpio ocelot-sgpio.1.auto: DMA mask not set
[ 2.863089] pinctrl-microchip-sgpio ocelot-sgpio.1.auto: invalid resource
[ 2.870801] gpiochip_find_base: found new base at 1962
[ 2.871528] gpio_stub_drv gpiochip5: (ocelot-sgpio.1.auto-input): added GPIO chardev (254:5)
[ 2.871666] gpio_stub_drv gpiochip5: registered GPIOs 1962 to 2025 on ocelot-sgpio.1.auto-input
[ 2.872364] gpiochip_find_base: found new base at 1898
[ 2.873244] gpio_stub_drv gpiochip6: (ocelot-sgpio.1.auto-output): added GPIO chardev (254:6)
[ 2.873354] gpio_stub_drv gpiochip6: registered GPIOs 1898 to 1961 on ocelot-sgpio.1.auto-output
[ 2.881148] mscc-miim ocelot-miim0.2.auto: DMA mask not set
[ 2.886929] mscc-miim ocelot-miim0.2.auto: invalid resource
[ 2.893738] mdio_bus ocelot-miim0.2.auto-mii: GPIO lookup for consumer reset
[ 2.893769] mdio_bus ocelot-miim0.2.auto-mii: using device tree for GPIO lookup
[ 2.893802] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/interconnect at 48000000/segment at 0/target-module at 30000/spi at 0/ocelot-chip at 0/mdio0[0]'
[ 2.893898] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/interconnect at 48000000/segment at 0/target-module at 30000/spi at 0/ocelot-chip at 0/mdio0[0]'
[ 2.893996] mdio_bus ocelot-miim0.2.auto-mii: using lookup tables for GPIO lookup
[ 2.894012] mdio_bus ocelot-miim0.2.auto-mii: No GPIO consumer reset found
[ 3.395738] mdio_bus ocelot-miim0.2.auto-mii:00: GPIO lookup for consumer reset
[ 3.395777] mdio_bus ocelot-miim0.2.auto-mii:00: using device tree for GPIO lookup
[ 3.395840] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/interconnect at 48000000/segment at 0/target-module at 30000/spi at 0/ocelot-chip at 0/mdio0/ethernet-phy at 0[0]'
[ 3.395959] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/interconnect at 48000000/segment at 0/target-module at 30000/spi at 0/ocelot-chip at 0/mdio0/ethernet-phy at 0[0]'
[ 3.396069] mdio_bus ocelot-miim0.2.auto-mii:00: using lookup tables for GPIO lookup
[ 3.396086] mdio_bus ocelot-miim0.2.auto-mii:00: No GPIO consumer reset found
...
[ 3.449187] ocelot-ext-switch ocelot-ext-switch.4.auto: DMA mask not set
[ 5.336880] ocelot-ext-switch ocelot-ext-switch.4.auto: PHY [ocelot-miim0.2.auto-mii:00] driver [Generic PHY] (irq=POLL)
[ 5.349087] ocelot-ext-switch ocelot-ext-switch.4.auto: configuring for phy/internal link mode
[ 5.363619] ocelot-ext-switch ocelot-ext-switch.4.auto swp1 (uninitialized): PHY [ocelot-miim0.2.auto-mii:01] driver [Generic PHY] (irq=POLL)
[ 5.381396] ocelot-ext-switch ocelot-ext-switch.4.auto swp2 (uninitialized): PHY [ocelot-miim0.2.auto-mii:02] driver [Generic PHY] (irq=POLL)
[ 5.398525] ocelot-ext-switch ocelot-ext-switch.4.auto swp3 (uninitialized): PHY [ocelot-miim0.2.auto-mii:03] driver [Generic PHY] (irq=POLL)
[ 5.422048] device eth0 entered promiscuous mode
[ 5.426785] DSA: tree 0 setup
...
[ 7.450067] ocelot-ext-switch ocelot-ext-switch.4.auto: Link is Up - 100Mbps/Full - flow control off
[ 21.556395] cpsw-switch 4a100000.switch: starting ndev. mode: dual_mac
[ 21.648564] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL)
[ 21.667970] 8021q: adding VLAN 0 to HW filter on device eth0
[ 21.705360] ocelot-ext-switch ocelot-ext-switch.4.auto swp1: configuring for phy/internal link mode
[ 22.018230] ocelot-ext-switch ocelot-ext-switch.4.auto: Link is Down
[ 23.771740] cpsw-switch 4a100000.switch eth0: Link is Up - 100Mbps/Full - flow control off
[ 24.090929] ocelot-ext-switch ocelot-ext-switch.4.auto: Link is Up - 100Mbps/Full - flow control off
[ 25.853021] ocelot-ext-switch ocelot-ext-switch.4.auto swp1: Link is Up - 1Gbps/Full - flow control rx/tx
RFC history:
v1 (accidentally named vN)
* Initial architecture. Not functional
* General concepts laid out
v2
* Near functional. No CPU port communication, but control over all
external ports
* Cleaned up regmap implementation from v1
v3
* Functional
* Shared MDIO transactions routed through mdio-mscc-miim
* CPU / NPI port enabled by way of vsc7512_enable_npi_port /
felix->info->enable_npi_port
* NPI port tagging functional - Requires a CPU port driver that supports
frames of 1520 bytes. Verified with a patch to the cpsw driver
v4
* Functional
* Device tree fixes
* Add hooks for pinctrl-ocelot - some functionality by way of sysfs
* Add hooks for pinctrl-microsemi-sgpio - not yet fully functional
* Remove lynx_pcs interface for a generic phylink_pcs. The goal here
is to have an ocelot_pcs that will work for each configuration of
every port.
v5
* Restructured to MFD
* Several commits were split out, submitted, and accepted
* pinctrl-ocelot believed to be fully functional (requires commits
from the linux-pinctrl tree)
* External MDIO bus believed to be fully functional
v6
* Applied several suggestions from the last RFC from Lee Jones. I
hope I didn't miss anything.
* Clean up MFD core - SPI interaction. They no longer use callbacks.
* regmaps get registered to the child device, and don't attempt to
get shared. It seems if a regmap is to be shared, that should be
solved with syscon, not dev or mfd.
v7
* Applied as much as I could from Lee and Vladimir's suggestions. As
always, the feedback is greatly appreciated!
* Remove "ocelot_spi" container complication
* Move internal MDIO bus from ocelot_ext to MFD, with a devicetree
change to match
* Add initial HSIO support
* Switch to IORESOURCE_REG for resource definitions
v8
* Applied another round of suggestions from Lee and Vladimir
* Utilize regmap bus reads, which speeds bulk transfers up by an
order of magnitude
* Add two additional patches to utilize phylink_generic_validate
* Changed GPL V2 to GPL in licenses where applicable (checkpatch)
* Remove initial hsio/serdes changes from the RFC
Colin Foster (16):
pinctrl: ocelot: allow pinctrl-ocelot to be loaded as a module
pinctrl: microchip-sgpio: allow sgpio driver to be used as a module
net: ocelot: add interface to get regmaps when exernally controlled
net: mdio: mscc-miim: add ability to be used in a non-mmio
configuration
pinctrl: ocelot: add ability to be used in a non-mmio configuration
pinctrl: microchip-sgpio: add ability to be used in a non-mmio
configuration
resource: add define macro for register address resources
mfd: ocelot: add support for the vsc7512 chip via spi
net: mscc: ocelot: expose ocelot wm functions
net: dsa: felix: add configurable device quirks
net: mscc: ocelot: expose regfield definition to be used by other
drivers
net: mscc: ocelot: expose stats layout definition to be used by other
drivers
net: mscc: ocelot: expose vcap_props structure
net: dsa: ocelot: add external ocelot switch control
net: dsa: felix: add phylink_get_caps capability
net: dsa: ocelot: utilize phylink_generic_validate
drivers/mfd/Kconfig | 18 +
drivers/mfd/Makefile | 2 +
drivers/mfd/ocelot-core.c | 138 ++++++++
drivers/mfd/ocelot-spi.c | 311 +++++++++++++++++
drivers/mfd/ocelot.h | 34 ++
drivers/net/dsa/ocelot/Kconfig | 14 +
drivers/net/dsa/ocelot/Makefile | 5 +
drivers/net/dsa/ocelot/felix.c | 29 +-
drivers/net/dsa/ocelot/felix.h | 3 +
drivers/net/dsa/ocelot/felix_vsc9959.c | 1 +
drivers/net/dsa/ocelot/ocelot_ext.c | 366 +++++++++++++++++++++
drivers/net/dsa/ocelot/seville_vsc9953.c | 1 +
drivers/net/ethernet/mscc/ocelot_devlink.c | 31 ++
drivers/net/ethernet/mscc/ocelot_vsc7514.c | 230 +------------
drivers/net/ethernet/mscc/vsc7514_regs.c | 200 +++++++++++
drivers/net/mdio/mdio-mscc-miim.c | 31 +-
drivers/pinctrl/Kconfig | 4 +-
drivers/pinctrl/pinctrl-microchip-sgpio.c | 26 +-
drivers/pinctrl/pinctrl-ocelot.c | 35 +-
include/linux/ioport.h | 5 +
include/soc/mscc/ocelot.h | 19 ++
include/soc/mscc/vsc7514_regs.h | 6 +
22 files changed, 1251 insertions(+), 258 deletions(-)
create mode 100644 drivers/mfd/ocelot-core.c
create mode 100644 drivers/mfd/ocelot-spi.c
create mode 100644 drivers/mfd/ocelot.h
create mode 100644 drivers/net/dsa/ocelot/ocelot_ext.c
--
2.25.1
More information about the linux-arm-kernel
mailing list