[PATCH v2 09/11] dt-bindings: display: convert Arm HDLCD to DT schema

[Andre Przywara]

The Arm HDLCD is a display controller that scans out a framebuffer and
hands a signal to a digital encoder to generate a DVI or HDMI signal.

Convert the existing DT binding to DT schema.

Signed-off-by: Andre Przywara <andre.przywara at arm.com>
---
 .../devicetree/bindings/display/arm,hdlcd.txt | 79 ----------------
 .../bindings/display/arm,hdlcd.yaml           | 89 +++++++++++++++++++
 2 files changed, 89 insertions(+), 79 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/arm,hdlcd.txt
 create mode 100644 Documentation/devicetree/bindings/display/arm,hdlcd.yaml

diff --git a/Documentation/devicetree/bindings/display/arm,hdlcd.txt b/Documentation/devicetree/bindings/display/arm,hdlcd.txt
deleted file mode 100644
index 78bc24296f3e4..0000000000000
--- a/Documentation/devicetree/bindings/display/arm,hdlcd.txt
+++ /dev/null
@@ -1,79 +0,0 @@
-ARM HDLCD
-
-This is a display controller found on several development platforms produced
-by ARM Ltd and in more modern of its' Fast Models. The HDLCD is an RGB
-streamer that reads the data from a framebuffer and sends it to a single
-digital encoder (DVI or HDMI).
-
-Required properties:
-  - compatible: "arm,hdlcd"
-  - reg: Physical base address and length of the controller's registers.
-  - interrupts: One interrupt used by the display controller to notify the
-    interrupt controller when any of the interrupt sources programmed in
-    the interrupt mask register have activated.
-  - clocks: A list of phandle + clock-specifier pairs, one for each
-    entry in 'clock-names'.
-  - clock-names: A list of clock names. For HDLCD it should contain:
-      - "pxlclk" for the clock feeding the output PLL of the controller.
-
-Required sub-nodes:
-  - port: The HDLCD connection to an encoder chip. The connection is modeled
-    using the OF graph bindings specified in
-    Documentation/devicetree/bindings/graph.txt.
-
-Optional properties:
-  - memory-region: phandle to a node describing memory (see
-    Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) to be
-    used for the framebuffer; if not present, the framebuffer may be located
-    anywhere in memory.
-
-
-Example:
-
-/ {
-	...
-
-	hdlcd at 2b000000 {
-		compatible = "arm,hdlcd";
-		reg = <0 0x2b000000 0 0x1000>;
-		interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&oscclk5>;
-		clock-names = "pxlclk";
-		port {
-			hdlcd_output: endpoint at 0 {
-				remote-endpoint = <&hdmi_enc_input>;
-			};
-		};
-	};
-
-	/* HDMI encoder on I2C bus */
-	i2c at 7ffa0000 {
-		....
-		hdmi-transmitter at 70 {
-			compatible = ".....";
-			reg = <0x70>;
-			port at 0 {
-				hdmi_enc_input: endpoint {
-					remote-endpoint = <&hdlcd_output>;
-				};
-
-				hdmi_enc_output: endpoint {
-					remote-endpoint = <&hdmi_1_port>;
-				};
-			};
-		};
-
-	};
-
-	hdmi1: connector at 1 {
-		compatible = "hdmi-connector";
-		type = "a";
-		port {
-			hdmi_1_port: endpoint {
-				remote-endpoint = <&hdmi_enc_output>;
-			};
-		};
-	};
-
-	...
-};
diff --git a/Documentation/devicetree/bindings/display/arm,hdlcd.yaml b/Documentation/devicetree/bindings/display/arm,hdlcd.yaml
new file mode 100644
index 0000000000000..a2670258c48d3
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/arm,hdlcd.yaml
@@ -0,0 +1,89 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/arm,hdlcd.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Arm HDLCD display controller binding
+
+maintainers:
+  - Liviu Dudau <Liviu.Dudau at arm.com>
+  - Andre Przywara <andre.przywara at arm.com>
+
+description:
+  The Arm HDLCD is a display controller found on several development platforms
+  produced by ARM Ltd and in more modern of its Fast Models. The HDLCD is an
+  RGB streamer that reads the data from a framebuffer and sends it to a single
+  digital encoder (DVI or HDMI).
+
+properties:
+  compatible:
+    const: arm,hdlcd
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clock-names:
+    const: pxlclk
+
+  clocks:
+    maxItems: 1
+    description: The input reference for the pixel clock.
+
+  memory-region:
+    maxItems: 1
+    description:
+      Phandle to a node describing memory to be used for the framebuffer.
+      If not present, the framebuffer may be located anywhere in memory.
+
+  iommus:
+    maxItems: 1
+
+  port:
+    $ref: /schemas/graph.yaml#/properties/port
+    unevaluatedProperties: false
+    description:
+      Output endpoint of the controller, connecting the LCD panel signals.
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - port
+
+examples:
+  - |
+    hdlcd at 2b000000 {
+        compatible = "arm,hdlcd";
+        reg = <0x2b000000 0x1000>;
+        interrupts = <0 85 4>;
+        clocks = <&oscclk5>;
+        clock-names = "pxlclk";
+        port {
+            hdlcd_output: endpoint {
+                remote-endpoint = <&hdmi_enc_input>;
+            };
+        };
+    };
+
+    /* HDMI encoder on I2C bus */
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        hdmi-transmitter at 70 {
+            compatible = "nxp,tda998x";
+            reg = <0x70>;
+            port {
+                hdmi_enc_input: endpoint {
+                    remote-endpoint = <&hdlcd_output>;
+                };
+            };
+        };
+    };
+...
-- 
2.25.1