[PATCH 2/6] dt-bindings: rtc: stm32: add alarm A out property to select output

[Rob Herring]

On Wed, May 04, 2022 at 03:06:13PM +0200, Valentin Caron wrote:
> STM32 RTC can pulse some SOC pins when an alarm of RTC expires.
> 
> This patch adds property to activate alarm A output. The pulse can
> output on three pins RTC_OUT1, RTC_OUT2, RTC_OUT2_RMP
> (PC13, PB2, PI8 on stm32mp15) (PC13, PB2, PI1 on stm32mp13).
> 
> Signed-off-by: Valentin Caron <valentin.caron at foss.st.com>
> ---
>  .../devicetree/bindings/rtc/st,stm32-rtc.yaml | 19 ++++++++++++++++++-
>  1 file changed, 18 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/rtc/st,stm32-rtc.yaml b/Documentation/devicetree/bindings/rtc/st,stm32-rtc.yaml
> index 56d46ea35c5d..71e02604e8de 100644
> --- a/Documentation/devicetree/bindings/rtc/st,stm32-rtc.yaml
> +++ b/Documentation/devicetree/bindings/rtc/st,stm32-rtc.yaml
> @@ -59,6 +59,13 @@ properties:
>        Refer to <include/dt-bindings/rtc/rtc-stm32.h> for the supported values.
>        Pinctrl state named "default" may be defined to reserve pin for RTC output.
>  
> +  st,alarm:
> +    $ref: "/schemas/types.yaml#/definitions/uint32"
> +    description: |
> +      To select and enable RTC Alarm A output.
> +      Refer to <include/dt-bindings/rtc/rtc-stm32.h> for the supported values.

No, sorry, you need to define the allowed values as a schema here.

> +      Pinctrl state named "default" may be defined to reserve pin for RTC output.
> +
>  allOf:
>    - if:
>        properties:
> @@ -75,6 +82,9 @@ allOf:
>          st,lsco:
>            maxItems: 0
>  
> +        st,alarm:
> +          maxItems: 0

st,alarm: false

or:

not:
  required: [ st,alarm ]

is how you disallow a property.

This should cause a warning, but this patch didn't apply for me.

> +
>          clock-names: false
>  
>        required:
> @@ -95,6 +105,9 @@ allOf:
>          st,lsco:
>            maxItems: 0
>  
> +        st,alarm:
> +          maxItems: 0
> +
>        required:
>          - clock-names
>          - st,syscfg
> @@ -117,6 +130,9 @@ allOf:
>          st,lsco:
>            maxItems: 1
>  
> +        st,alarm:
> +          maxItems: 1

maxItems applies to arrays, but this is a scalar value. I don't think 
you need this hunk.

> +
>        required:
>          - clock-names
>  
> @@ -153,8 +169,9 @@ examples:
>        clocks = <&rcc RTCAPB>, <&rcc RTC>;
>        clock-names = "pclk", "rtc_ck";
>        interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> +      st,alarm = <RTC_OUT1>;
>        st,lsco = <RTC_OUT2_RMP>;
> -      pinctrl-0 = <&rtc_out2_rmp_pins_a>;
> +      pinctrl-0 = <&rtc_out1_pins_a &rtc_out2_rmp_pins_a>;
>        pinctrl-names = "default";
>      };
>  
> -- 
> 2.25.1
> 
>