[PATCH v24 0/7] soc: mediatek: SVS: introduce MTK SVS
Chen-Yu Tsai
wenst at chromium.org
Mon May 2 23:13:52 PDT 2022
On Tue, May 3, 2022 at 6:08 AM Kevin Hilman <khilman at kernel.org> wrote:
>
> Chen-Yu Tsai <wenst at chromium.org> writes:
>
> > On Fri, Apr 22, 2022 at 11:38 PM Matthias Brugger
> > <matthias.bgg at gmail.com> wrote:
> >>
> >>
> >>
> >> On 22/04/2022 04:24, Roger Lu wrote:
> >> > Hi Kevin,
> >> >
> >> > On Thu, 2022-04-21 at 12:41 -0700, Kevin Hilman wrote:
> >> >> Hi Roger,
> >> >>
> >> >> Roger Lu <roger.lu at mediatek.com> writes:
> >> >>
> >> >>> On Wed, 2022-04-20 at 16:22 -0700, Kevin Hilman wrote:
> >> >>
> >> >> [...]
> >> >>
> >> >>>> That being said, it would be really nice to see an integration tree
> >> >>>> where this was all tested on mainline (e.g. v5.17, or v5.18-rc)
> >> >>>>
> >> >>>> For example, I can apply this to v5.18-rc2 and boot on my mt8183-pumpkin
> >> >>>> board, it fails to probe[1] because there is no CCI node in the upstream
> >> >>>> mt8183.dtsi.
> >> >>>>
> >> >>>> I'm assuming this series is also not very useful without the CPUfreq
> >> >>>> series from Rex, so being able to test this, CCI and CPUfreq together on
> >> >>>> MT8183 on a mainline kernel would be very helpful.
> >> >>>>
> >> >>>> Kevin
> >> >>>>
> >> >>>> [1]
> >> >>>> [ 0.573332] mtk-svs 1100b000.svs: cannot find cci node
> >> >>>> [ 0.574061] mtk-svs 1100b000.svs: error -ENODEV: svs platform probe
> >> >>>> fail
> >> >>>
> >> >>> Just share. I've tested this series on below two platforms and it works as
> >> >>> expected.
> >> >>> - mt8183-Krane (kernel-v5.10)
> >> >>> - mt8192-Hayato (kernel-v5.4)
> >> >>
> >> >> Unfortunately testing on v5.4 and v5.10 with lots of other additional
> >> >> out-of-tree patches does not give much confidence that this series works
> >> >> with upstream, especially when I've given a few reasons why it will not
> >> >> work uptream.
> >> >>
> >> >> The examples I gave above for CCI and CPUs/cluster disable are good
> >> >> examples, but another one I forgot to mention is the dependency on Mali.
> >> >> The SVS driver will never probe because it also depens on a "mali" node,
> >> >> which doesn't exist upstream either (but panfrost does, and acutually
> >> >> loads/probes fine on v5.17/v5.18) so this should be fixed to work with
> >> >> upstream panfrost.
> >> >>
> >> >> IMO, in order for this to be merged upstream, it should at least have
> >> >> some basic validation with upstream, and so far I have not even been
> >> >> able to make it successfuly probe. To do that, you will need to either
> >> >> provide a list of the dependencies for testing this with mainline
> >> >> (e.g. CCI series, CPUfreq series, any DT changes), or even better, an
> >> >> integration tree based on recent mainline (e.g. v5.17 stable, or
> >> >> v5.18-rc) which shows all the patches (in addition to this series) used
> >> >> to validate this on mainline.
> >> >
> >> > No problem. We'll find a machine that can be run correctly with recent mainline
> >> > (e.g. v5.17 stable, or v5.18-rc) and add patches (CCI series + CPUfreq series +
> >> > any DT changes) to test this SVS series. Thanks very much.
> >> >
> >>
> >> Thanks Roger. I'll wait until this got tested with upstream Linux, before I will
> >> apply all the patches.
> >
> > Hi everyone,
> >
> > I've put together an integration test branch:
> >
> > https://github.com/wens/linux/commits/mt8183-cpufreq-cci-svs-test
> >
> > This branch is based on next-20220422 and includes the following series:
> >
> > - ANX7625 DPI support v2
> > https://lore.kernel.org/all/20220422084720.959271-1-xji@analogixsemi.com/
> > - MTK SVS v24
> > https://lore.kernel.org/all/20220420102044.10832-1-roger.lu@mediatek.com/
> > - MTK cpufreq v4
> > https://lore.kernel.org/all/20220422075239.16437-1-rex-bc.chen@mediatek.com/
> > - PM / devfreq core patches from
> > http://git.kernel.org/chanwoo/h/devfreq-testing
> > PM / devfreq: Export devfreq_get_freq_range symbol within devfreq
> > PM / devfreq: Add cpu based scaling support to passive governor
> > PM / devfreq: passive: Reduce duplicate code when passive_devfreq case
> > PM / devfreq: passive: Update frequency when start governor
> > - CCI devfreq v2
> > https://lore.kernel.org/all/20220408052150.22536-1-johnson.wang@mediatek.com/
> >
> > And some patches of my own to fix some errors. See the last handful of
> > patches including and after the fixup! one.
>
> Thanks for setting up this branch.
>
> > This was tested on Juniper (Acer Chromebook Spin 311) that has MT8183.
>
> Is there an upstream DT for this platform?
mt8183-kukui-jacuzzi-juniper-sku16.dtb
> I tried this series on mt8183-pumpkin, and since the upstream DT doesn't
> define a CCI regulator, the CCI driver fails to probe. Without CCI, the
> SVS driver also fails to probe. So the platform boots, but has neither
> CCI nor SVS.
>
> If I add a regulator for CCI[1], it goes farther, but then fails more
> noisly[2]
Interesting. That doesn't happen on my system.
> > Looking at the mcu_*_sel clocks from /sys/kernel/debug/clk/clk_summary ,
> > it does seem like things are happening, though I'm not sure how to
> > thoroughly test this, especially SVS.
>
> I think you're probably seeing CPU DVFS (CPUfreq) working, but I suspect
> neither CCI or SVS have successfully loaded.
I can see CCI devfreq stats, and the clk rate being changed around:
# cat /sys/class/devfreq/cci/trans_stat
From : To
: 273000000 338000000 403000000 463000000 546000000
624000000 689000000 767000000 845000000 871000000 923000000
9620000001027000000109200000011440000001196000000 time(ms)
273000000: 0 207 48 74 71
34 27 9 7 9 2 1
3 5 3 13 159715
* 338000000: 268 0 95 65 17
11 2 11 6 9 1 0
4 2 1 11 48589
403000000: 54 99 0 76 19
5 4 7 3 1 2 1
1 0 0 10 13320
463000000: 61 83 73 0 35
7 6 7 1 0 1 1
2 0 2 14 11628
546000000: 63 51 21 20 0
11 3 2 2 0 2 0
2 1 0 9 7919
624000000: 28 9 8 8 7
0 10 2 2 3 1 0
2 3 0 14 3030
689000000: 19 8 4 9 7
4 0 6 6 1 4 2
4 1 1 7 3908
767000000: 4 10 8 8 5
3 3 0 1 1 1 1
1 0 1 12 667
845000000: 2 4 2 3 3
3 3 1 0 1 4 1
1 0 0 10 417
871000000: 1 1 2 2 7
3 2 1 1 0 1 1
1 0 0 14 341
923000000: 2 4 1 2 3
2 1 0 0 1 0 1
4 2 0 8 131
962000000: 2 2 0 1 1
1 1 0 1 3 1 0
2 0 0 5 147
1027000000: 0 4 0 2 2
2 6 1 1 3 1 2
0 5 0 5 105
1092000000: 0 4 2 2 1
3 2 2 0 3 1 3
0 0 6 17 193
1144000000: 1 0 2 2 1
0 1 0 0 0 0 0
0 2 0 20 105
1196000000: 8 18 16 19 8
8 12 10 7 2 9 6
7 25 15 0 14210
Total transition : 2422
For SVS, it looks like we need to make Panfrost/OPP understand the 2
regulator supply design of the GPU:
mtk-svs 1100b000.svs: M_HW_RES0: 0x00120090
mtk-svs 1100b000.svs: M_HW_RES1: 0xe6fcbb1b
mtk-svs 1100b000.svs: M_HW_RES2: 0x478b47c7
mtk-svs 1100b000.svs: M_HW_RES3: 0xaafbf757
mtk-svs 1100b000.svs: M_HW_RES4: 0xe6fca3ec
mtk-svs 1100b000.svs: M_HW_RES5: 0x47bd4b90
mtk-svs 1100b000.svs: M_HW_RES6: 0xaafb87ab
mtk-svs 1100b000.svs: M_HW_RES7: 0xe6fc9032
mtk-svs 1100b000.svs: M_HW_RES8: 0x4bbd4bf1
mtk-svs 1100b000.svs: M_HW_RES9: 0xaafbd97f
mtk-svs 1100b000.svs: M_HW_RES14: 0xf6ce0dcb
mtk-svs 1100b000.svs: M_HW_RES15: 0x025a0015
mtk-svs 1100b000.svs: M_HW_RES16: 0xe6fc8d1f
mtk-svs 1100b000.svs: M_HW_RES17: 0x47bd47f1
mtk-svs 1100b000.svs: M_HW_RES18: 0xaafbc050
panfrost 13040000.gpu: opp_parse_supplies: Invalid number of elements
in opp-microvolt property (2) with supplies (1)
panfrost 13040000.gpu: _of_add_opp_table_v2: Failed to add OPP, -22
SVSB_GPU: add opp table fail: -22
mtk-svs 1100b000.svs: svs bank resource setup fail: -22
mtk-svs: probe of 1100b000.svs failed with error -22
Regards
ChenYu
> Kevin
>
>
>
> [1]
> diff --git a/arch/arm64/boot/dts/mediatek/mt8183-pumpkin.dts b/arch/arm64/boot/dts/mediatek/mt8183-pumpkin.dts
> index b288b508fa4c..e064c06dc0d7 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8183-pumpkin.dts
> +++ b/arch/arm64/boot/dts/mediatek/mt8183-pumpkin.dts
> @@ -384,6 +384,10 @@ &mfg {
> domain-supply = <&mt6358_vgpu_reg>;
> };
>
> +&cci {
> + proc-supply = <&mt6358_vproc12_reg>;
> +};
> +
> &cpu0 {
> proc-supply = <&mt6358_vproc12_reg>;
> };
>
>
> [2]
> [ 0.560083] mtk-ccifreq cci: devfreq_add_device: Unable to start governor for the device
> [ 0.576083] ------------[ cut here ]------------
> [ 0.576670] WARNING: CPU: 3 PID: 1 at drivers/devfreq/governor_passive.c:382 devfreq_passive_event_handler+0x80/0x3a0
> [ 0.578021] Modules linked in:
> [ 0.578413] CPU: 3 PID: 1 Comm: swapper/0 Not tainted 5.18.0-rc3-next-20220422-05886-g9cd0610279c1-dirty #58
> [ 0.579653] Hardware name: Pumpkin MT8183 (DT)
> [ 0.580217] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
> [ 0.581097] pc : devfreq_passive_event_handler+0x80/0x3a0
> [ 0.581780] lr : devfreq_passive_event_handler+0x7c/0x3a0
> [ 0.582463] sp : ffff80000808ba40
> [ 0.582883] x29: ffff80000808ba40 x28: 0000000000000000 x27: fffffffffffffdfb
> [ 0.583788] x26: ffff0000037ba810 x25: ffff80000808bb40 x24: ffff80000a406640
> [ 0.584691] x23: ffff8000099153c8 x22: ffff0000037ba800 x21: 0000000000000000
> [ 0.585595] x20: ffff0000035c40a0 x19: ffff0000035c4080 x18: 0000000000000000
> [ 0.586267] mmc0: new ultra high speed SDR104 SDIO card at address 0001
> [ 0.586498] x17: 6f6620726f6e7265 x16: 766f672074726174 x15: 000006837f6218f7
> [ 0.588233] x14: 0000000000000320 x13: 0000000000000001 x12: 0000000000000000
> [ 0.589137] x11: 0000000000000001 x10: 0000000000000a50 x9 : ffff80000808b7a0
> [ 0.590041] x8 : ffff0000028b0ab0 x7 : ffff00007fb19d00 x6 : 00000000076832c3
> [ 0.590945] x5 : 00000000410fd030 x4 : 0000000000000000 x3 : ffff80000a3f70e8
> [ 0.591849] x2 : 0000000000000000 x1 : ffff0000028b0000 x0 : 00000000fffffffe
> [ 0.592753] Call trace:
> [ 0.593065] devfreq_passive_event_handler+0x80/0x3a0
> [ 0.593706] devfreq_remove_device+0x38/0xd0
> [ 0.594247] devfreq_add_device+0x328/0x5f0
> [ 0.594778] devm_devfreq_add_device+0x64/0xb0
> [ 0.595341] mtk_ccifreq_probe+0x340/0x4e0
> [ 0.595860] platform_probe+0x68/0xe0
> [ 0.596330] really_probe.part.0+0x9c/0x29c
> [ 0.596862] __driver_probe_device+0x98/0x144
> [ 0.597416] driver_probe_device+0xac/0x140
> [ 0.597948] __driver_attach+0xf8/0x190
> [ 0.598436] bus_for_each_dev+0x70/0xd0
> [ 0.598925] driver_attach+0x24/0x30
> [ 0.599380] bus_add_driver+0x14c/0x1f0
> [ 0.599868] driver_register+0x78/0x130
> [ 0.600356] __platform_driver_register+0x28/0x34
> [ 0.600954] mtk_ccifreq_platdrv_init+0x1c/0x28
> [ 0.601531] do_one_initcall+0x50/0x1c0
> [ 0.602021] kernel_init_freeable+0x20c/0x290
> [ 0.602576] kernel_init+0x28/0x13c
> [ 0.603024] ret_from_fork+0x10/0x20
> [ 0.603480] ---[ end trace 0000000000000000 ]---
>
More information about the linux-arm-kernel
mailing list