[PATCH v2 2/4] arm64: dts: mediatek: Add device-tree for MT8195 Demo board

[AngeloGioacchino Del Regno]

Il 27/03/22 22:03, Fabien Parent ha scritto:
> Add basic device-tree for the MT8195 Demo board. The
> Demo board is made by MediaTek and has a MT8195 SoC,
> associated with the MT6359 and MT6360 PMICs, and
> the MT7921 connectivity chip.
> 
> The IOs available on that board are:
> * 1 USB Type-C connector with DP aux mode support
> * 1 USB Type-A connector
> * 1 full size HDMI RX and 1 full size HDMI TX connector
> * 1 uSD slot
> * 40 pins header
> * SPI interface header
> * 1 M.2 slot
> * 1 audio jack
> * 1 micro-USB port for serial debug
> * 2 connectors for DSI displays
> * 3 connectors for CSI cameras
> * 1 connector for a eDP panel
> * 1 MMC storage
> 
> This commit adds basic support in order to be able to boot.
> 
> Signed-off-by: Fabien Parent <fparent at baylibre.com>
> ---
> v2:
>   * remove empty i2c nodes
>   * remove empty spi node
>   * remove unused pcie pinctrls
>   * fixup node nodes to not contains underscore
>   * rename mt6360 pmic node
>   * move mmc1 node right after mmc0 node
>   * use generic node name for gpio-keys
>   * uniformize pinctrl node names
> 
>   arch/arm64/boot/dts/mediatek/Makefile        |   1 +
>   arch/arm64/boot/dts/mediatek/mt8195-demo.dts | 447 +++++++++++++++++++
>   2 files changed, 448 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/mediatek/mt8195-demo.dts
> 

..snip..

> diff --git a/arch/arm64/boot/dts/mediatek/mt8195-demo.dts b/arch/arm64/boot/dts/mediatek/mt8195-demo.dts
> new file mode 100644
> index 000000000000..d94b4e01159a
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8195-demo.dts
> @@ -0,0 +1,447 @@

..snip..

> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		input-name = "gpio-keys";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&gpio_keys_pins>;
> +
> +		key-0 {

key-volup is more descriptive, can you please change that?

> +			gpios = <&pio 106 GPIO_ACTIVE_LOW>;
> +			label = "volume_up";
> +			linux,code = <KEY_VOLUMEUP>;
> +			wakeup-source;
> +			debounce-interval = <15>;
> +		};
> +	};
> +};
> +

..snip..

> +
> +&pmic {
> +	interrupt-parent = <&pio>;
> +	interrupts = <222 IRQ_TYPE_LEVEL_HIGH>;

I would instead use interrupts-extended here:

	interrupts-extended = <&pio 222 IRQ_TYPE_LEVEL_HIGH>;

> +};
> +
> +&i2c6 {
> +	clock-frequency = <400000>;
> +	pinctrl-0 = <&i2c6_pins>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	mt6360: pmic at 34 {
> +		compatible = "mediatek,mt6360";
> +		reg = <0x34>;
> +		interrupt-controller;
> +		interrupt-parent = <&pio>;
> +		interrupts = <101 IRQ_TYPE_EDGE_FALLING>;

Same here

> +		interrupt-names = "IRQB";
> +

...snip...

> +
> +&pio {
> +	mmc0_default_pins: mmc0-default-pins {
> +		pins-cmd-dat {
> +			pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
> +				 <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
> +				 <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
> +				 <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
> +				 <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
> +				 <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
> +				 <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
> +				 <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
> +				 <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
> +			input-enable;
> +			drive-strength = <MTK_DRIVE_6mA>;
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> +		};
> +
> +		pin-clk {

This is supposed to be "pins-clk", not "pin-clk"... same for all the other
instances of the "pin-".

Before pushing patches upstream, please run dtbs_check, as these are all
mistakes that will be pointed out by that.

Regards,
Angelo