[PATCH 2/3] dt-bindings: i2c: convert i2c-at91 to json-schema

[Sergiu.Moga at microchip.com]

On 10.03.2022 09:21, Krzysztof Kozlowski wrote:
> On 09/03/2022 13:07, Sergiu Moga wrote:
>> Convert I2C binding for Atmel/Microchip SoCs to Device Tree Schema
>> format.
>>
>> Signed-off-by: Sergiu Moga <sergiu.moga at microchip.com>
>> ---
>>   .../bindings/i2c/atmel,at91sam-i2c.yaml       | 144 ++++++++++++++++++
>>   .../devicetree/bindings/i2c/i2c-at91.txt      |  82 ----------
>>   2 files changed, 144 insertions(+), 82 deletions(-)
>>   create mode 100644 Documentation/devicetree/bindings/i2c/atmel,at91sam-i2c.yaml
>>   delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-at91.txt
>>
>> diff --git a/Documentation/devicetree/bindings/i2c/atmel,at91sam-i2c.yaml b/Documentation/devicetree/bindings/i2c/atmel,at91sam-i2c.yaml
>> new file mode 100644
>> index 000000000000..d4aadbbd1a11
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/i2c/atmel,at91sam-i2c.yaml
>> @@ -0,0 +1,144 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +# Copyright (C) 2022 Microchip Technology, Inc. and its subsidiaries
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/i2c/atmel,at91sam-i2c.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: I2C for Atmel/Microchip platforms
>> +
>> +maintainers:
>> +  - Alexandre Belloni <alexandre.belloni at bootlin.com>
>> +
>> +allOf:
>> +  - $ref: "i2c-controller.yaml"
>> +  - if:
> allOf with additional if: goes by convention after required:.
>
Understood. I will move the `allOf` after `required:`.

>> +      properties:
>> +        compatible:
>> +          contains:
>> +            enum:
>> +              - atmel,sama5d4-i2c
>> +              - atmel,sama5d2-i2c
>> +              - microchip,sam9x60-i2c
>> +    then:
>> +      properties:
>> +        i2c-sda-hold-time-ns:
>> +          description:
>> +            TWD hold time
>> +          maxItems: 1
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - atmel,at91rm9200-i2c
>> +      - atmel,at91sam9261-i2c
>> +      - atmel,at91sam9260-i2c
>> +      - atmel,at91sam9g20-i2c
>> +      - atmel,at91sam9g10-i2c
>> +      - atmel,at91sam9x5-i2c
>> +      - atmel,sama5d4-i2c
>> +      - atmel,sama5d2-i2c
>> +      - microchip,sam9x60-i2c
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +  interrupts:
>> +    maxItems: 1
>> +
>> +  "#address-cells":
>> +    const: 1
>> +
>> +  "#size-cells":
>> +    const: 0
>> +
>> +  clocks:
>> +    maxItems: 1
>> +
>> +  clock-frequency:
>> +    default: 100000
>> +
>> +  dmas:
>> +    items:
>> +      - description: TX DMA Channel Specifier
>> +      - description: RX DMA Channel Specifier
>> +
>> +  dma-names:
>> +    items:
>> +      - const: tx
>> +      - const: rx
>> +
>> +  atmel,fifo-size:
>> +    $ref: /schemas/types.yaml#/definitions/uint32
>> +    description: |
>> +      Maximum number of data the RX and TX FIFOs can store for
>> +      FIFO capable I2C controllers.
>> +
>> +  scl-gpios: true
>> +
>> +  sda-gpios: true
>> +
>> +  pinctrl:
>> +    description: |
>> +      Add extra pinctrl to configure i2c pins to gpio function for i2c
>> +      bus recovery, call it "gpio" state
> This is a generic property, you do not need it.
>
Will remove it in the next version. Thank you.

>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +  - interrupts
>> +  - "#address-cells"
>> +  - "#size-cells"
>> +  - clocks
>> +
>> +unevaluatedProperties: false
>> +
>> +examples:
>> +  - |
>> +    #include <dt-bindings/interrupt-controller/irq.h>
>> +    #include <dt-bindings/dma/at91.h>
>> +    #include <dt-bindings/gpio/gpio.h>
>> +
>> +    i2c0: i2c at fff84000 {
>> +        compatible = "atmel,at91sam9g20-i2c";
>> +        reg = <0xfff84000 0x100>;
>> +        interrupts = <12 IRQ_TYPE_LEVEL_HIGH 6>;
>> +        #address-cells = <1>;
>> +        #size-cells = <0>;
>> +        clocks = <&twi0_clk>;
>> +        clock-frequency = <400000>;
>> +
>> +        eeprom at 50 {
>> +            compatible = "atmel,24c512";
>> +            reg = <0x50>;
>> +            pagesize = <128>;
>> +        };
>> +    };
>> +
>> +    i2c1: i2c at f8034600 {
>> +        compatible = "atmel,sama5d2-i2c";
>> +        reg = <0xf8034600 0x100>;
>> +        interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
>> +        dmas = <&dma0
>> +            (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1))
>> +            AT91_XDMAC_DT_PERID(11)>,
>> +               <&dma0
>> +            (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1))
>> +            AT91_XDMAC_DT_PERID(12)>;
>> +        dma-names = "tx", "rx";
>> +        #address-cells = <1>;
>> +        #size-cells = <0>;
>> +        clocks = <&flx0>;
>> +        atmel,fifo-size = <16>;
>> +        i2c-sda-hold-time-ns = <336>;
>> +        pinctrl-names = "default", "gpio";
>> +        pinctrl-0 = <&pinctrl_i2c0>;
>> +        pinctrl-1 = <&pinctrl_i2c0_gpio>;
>> +        sda-gpios = <&pioA 30 GPIO_ACTIVE_HIGH>;
>> +        scl-gpios = <&pioA 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
>> +
>> +        eeprom at 1a {
>> +            compatible = "wm8731";
> It seems this is undocumented compatible. Could you use something else,
> documented?
>
I will replace it with a node with a documented compatible in the next 
version.

> Best regards,
> Krzysztof

Thank you for the feedback.

Sergiu