[PATCH 08/14] ARM: dts: suniv: F1C100: add MMC controllers

[Andre Przywara]

From: Jesse Taube <mr.bossman075 at gmail.com>

The F1C100 series contains two MMC controllers, where the first one is
typically connected to an (micro)SD card slot (as this is the one the
BROM is able to boot from).
Describe the two controllers in the SoC .dtsi.
We also add the pinctrl description for MMC0, since this is the only
pin set supporting that function anyway, and SD cards are very common
across boards.

Signed-off-by: Jesse Taube <Mr.Bossman075 at gmail.com>
Signed-off-by: Andre Przywara <andre.przywara at arm.com>
---
 arch/arm/boot/dts/suniv-f1c100s.dtsi | 42 ++++++++++++++++++++++++++++
 1 file changed, 42 insertions(+)

diff --git a/arch/arm/boot/dts/suniv-f1c100s.dtsi b/arch/arm/boot/dts/suniv-f1c100s.dtsi
index 57f8932ef898..6f2f97458fe0 100644
--- a/arch/arm/boot/dts/suniv-f1c100s.dtsi
+++ b/arch/arm/boot/dts/suniv-f1c100s.dtsi
@@ -69,6 +69,42 @@ otg_sram: sram-section at 0 {
 			};
 		};
 
+		mmc0: mmc at 1c0f000 {
+			compatible = "allwinner,suniv-f1c100s-mmc",
+				     "allwinner,sun7i-a20-mmc";
+			reg = <0x01c0f000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC0>,
+				 <&ccu CLK_MMC0>,
+				 <&ccu CLK_MMC0_OUTPUT>,
+				 <&ccu CLK_MMC0_SAMPLE>;
+			clock-names = "ahb", "mmc", "output", "sample";
+			resets = <&ccu RST_BUS_MMC0>;
+			reset-names = "ahb";
+			interrupts = <23>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc at 1c10000 {
+			compatible = "allwinner,suniv-f1c100s-mmc",
+				     "allwinner,sun7i-a20-mmc";
+			reg = <0x01c10000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC1>,
+				 <&ccu CLK_MMC1>,
+				 <&ccu CLK_MMC1_OUTPUT>,
+				 <&ccu CLK_MMC1_SAMPLE>;
+			clock-names = "ahb", "mmc", "output", "sample";
+			resets = <&ccu RST_BUS_MMC1>;
+			reset-names = "ahb";
+			interrupts = <24>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
 		ccu: clock at 1c20000 {
 			compatible = "allwinner,suniv-f1c100s-ccu";
 			reg = <0x01c20000 0x400>;
@@ -96,6 +132,12 @@ pio: pinctrl at 1c20800 {
 			#interrupt-cells = <3>;
 			#gpio-cells = <3>;
 
+			mmc0_pins: mmc0-pins {
+				pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5";
+				function = "mmc0";
+				drive-strength = <30>;
+			};
+
 			uart0_pe_pins: uart0-pe-pins {
 				pins = "PE0", "PE1";
 				function = "uart0";
-- 
2.25.1