[PATCH v3 5/8] ARM: dts: sun8i: v3s: Add nodes for MIPI CSI-2 support

[Paul Kocialkowski]

MIPI CSI-2 is supported on the V3s with an A31-based MIPI CSI-2 bridge
controller. The controller uses a separate D-PHY, which is the same
that is otherwise used for MIPI DSI, but used in Rx mode.

On the V3s, the CSI0 controller is dedicated to MIPI CSI-2 as it does
not have access to any parallel interface pins.

Add all the necessary nodes (CSI0, MIPI CSI-2 bridge and D-PHY) to
support the MIPI CSI-2 interface.

Note that a fwnode graph link is created between CSI0 and MIPI CSI-2
even when no sensor is connected. This will result in a probe failure
for the controller as long as no sensor is connected but this is fine
since no other interface is available.

The interconnects property is used to inherit the proper DMA offset.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski at bootlin.com>
---
 arch/arm/boot/dts/sun8i-v3s.dtsi | 71 ++++++++++++++++++++++++++++++++
 1 file changed, 71 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
index a966b6a9acf5..a9405e011f3e 100644
--- a/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
@@ -619,6 +619,77 @@ gic: interrupt-controller at 1c81000 {
 			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
 		};
 
+		csi0: camera at 1cb0000 {
+			compatible = "allwinner,sun8i-v3s-csi";
+			reg = <0x01cb0000 0x1000>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CSI>,
+				 <&ccu CLK_CSI1_SCLK>,
+				 <&ccu CLK_DRAM_CSI>;
+			clock-names = "bus", "mod", "ram";
+			resets = <&ccu RST_BUS_CSI>;
+			interconnects = <&mbus 5>;
+			interconnect-names = "dma-mem";
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port at 1 {
+					reg = <1>;
+
+					csi0_in_mipi_csi2: endpoint {
+						remote-endpoint = <&mipi_csi2_out_csi0>;
+					};
+				};
+			};
+		};
+
+		mipi_csi2: csi at 1cb1000 {
+			compatible = "allwinner,sun8i-v3s-mipi-csi2",
+				     "allwinner,sun6i-a31-mipi-csi2";
+			reg = <0x01cb1000 0x1000>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CSI>,
+				 <&ccu CLK_CSI1_SCLK>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_CSI>;
+			status = "disabled";
+
+			phys = <&dphy>;
+			phy-names = "dphy";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				mipi_csi2_in: port at 0 {
+					reg = <0>;
+				};
+
+				mipi_csi2_out: port at 1 {
+					reg = <1>;
+
+					mipi_csi2_out_csi0: endpoint {
+						remote-endpoint = <&csi0_in_mipi_csi2>;
+					};
+				};
+			};
+		};
+
+		dphy: d-phy at 1cb2000 {
+			compatible = "allwinner,sun6i-a31-mipi-dphy";
+			reg = <0x01cb2000 0x1000>;
+			clocks = <&ccu CLK_BUS_CSI>,
+				 <&ccu CLK_MIPI_CSI>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_CSI>;
+			allwinner,direction = "rx";
+			status = "disabled";
+			#phy-cells = <0>;
+		};
+
 		csi1: camera at 1cb4000 {
 			compatible = "allwinner,sun8i-v3s-csi";
 			reg = <0x01cb4000 0x3000>;
-- 
2.35.1