[PATCH v2 0/2] Add SCMI full message tracing

[Cristian Marussi]

Hi,

after a few recent troubles handling too strictly out-of-spec replies from
SCMI servers deployed in the wild, I though it could have been useful to
have a basic way to dump at will the effective full payloads of
successfully transmitted/received SCMI messages.

The existing SCMI traces already collect a bunch of information about SCMI
message exchanges but they do NOT keep any payload information: this is
certainly preferable most of the time since dumping full SCMI messages to
the trace buffer involves a full copy of the payload.

For this reason I added a new distinct trace_scmi_msg_dump with this series
in order to be able to selectively enable at will message dumping only when
required.

Only successfully transmitted and received (valid) xfers are dumped.

Following the advice from Jim, I added some parsing/interpretation of the
header, so that the final result is something like:

root at deb-guest:~# echo 1 > /sys/kernel/debug/tracing/events/scmi/scmi_msg_dump/enable 
root at deb-guest:~# cat /sys/kernel/debug/tracing/trace_pipe 

 ++ cmd/reply
    sugov:0-257     [000] .....   401.954788: scmi_msg_dump: pt=13 t=CMND msg_id=07 seq=0082 s=0 pyld=0000000000000000
     <idle>-0       [000] d.h2.   401.955085: scmi_msg_dump: pt=13 t=RESP msg_id=07 seq=0082 s=0 pyld=


 ++ cmd/reply/delayed
   cat-263     [001] .....   471.533806: scmi_msg_dump: pt=15 t=CMND msg_id=06 seq=008A s=0 pyld=0100000001000000
<idle>-0       [000] d.h2.   471.554001: scmi_msg_dump: pt=15 t=RESP msg_id=06 seq=008A s=0 pyld=
<idle>-0       [000] d.h2.   471.574102: scmi_msg_dump: pt=15 t=DLYD msg_id=06 seq=008A s=0 pyld=01000000a05a320000000000efbeaddefecafeca


 ++ enable notif/notif
iio_generic_buf-282     [000] .....   535.327307: scmi_msg_dump: pt=15 t=CMND msg_id=0A seq=00AB s=0 pyld=0800000003000000
         <idle>-0       [000] d.h2.   535.327561: scmi_msg_dump: pt=15 t=RESP msg_id=0A seq=00AB s=0 pyld=00000000
         <idle>-0       [000] d.h2.   535.334421: scmi_msg_dump: pt=15 t=NOTI msg_id=01 seq=0000 s=0 pyld=000000000800000008daffffffffffff008268d4c075fd1610daffffffffffff008268d4c075fd1618daffffffffffff008268d4c075fd16
         <idle>-0       [000] d.h2.   535.434649: scmi_msg_dump: pt=15 t=NOTI msg_id=01 seq=0000 s=0 pyld=000000000800000009daffffffffffff008268d4c075fd1611daffffffffffff008268d4c075fd1619daffffffffffff008268d4c075fd16

Payload is dumped as it comes through byte-by-byte without any endianity
conversion to avoid further load on the system.

Thanks,
Cristian

---
V1 --> V2
- changed dumping format

Cristian Marussi (2):
  include: trace: Add SCMI full message tracing
  firmware: arm_scmi: Use new SCMI full message tracing

 drivers/firmware/arm_scmi/driver.c | 21 ++++++++++++++++++++
 include/trace/events/scmi.h        | 31 ++++++++++++++++++++++++++++++
 2 files changed, 52 insertions(+)

-- 
2.32.0