[PATCH V2 4/8] dt-bindings: pinctrl: qcom: Add ipq5018 pinctrl bindings

[Sricharan Ramabadhran]

On 6/22/2022 8:43 PM, Krzysztof Kozlowski wrote:
> On 21/06/2022 18:11, Sricharan R wrote:
>> From: Varadarajan Narayanan <quic_varada at quicinc.com>
>>
>> Add device tree binding Documentation details for ipq5018
>> pinctrl driver.
>>
>> Co-developed-by: Nitheesh Sekar <quic_nsekar at quicinc.com>
>> Co-developed-by: Sricharan R <quic_srichara at quicinc.com>
>> Signed-off-by: Sricharan R <quic_srichara at quicinc.com>
>> Signed-off-by: Nitheesh Sekar <quic_nsekar at quicinc.com>
>> Signed-off-by: Varadarajan Narayanan <quic_varada at quicinc.com>
> SoB should go after Co-developed.
>
> https://elixir.bootlin.com/linux/v5.17.1/source/Documentation/process/submitting-patches.rst#L473

  ok, will follow this.


>> ---
>>   .../pinctrl/qcom,ipq5018-pinctrl.yaml         | 145 ++++++++++++++++++
>>   1 file changed, 145 insertions(+)
>>   create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq5018-pinctrl.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq5018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq5018-pinctrl.yaml
>> new file mode 100644
>> index 000000000000..9b16c08bd127
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq5018-pinctrl.yaml
>> @@ -0,0 +1,145 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq5018-pinctrl.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Qualcomm Technologies, Inc. IPQ5018 TLMM block
>> +
>> +maintainers:
>> +  - Varadarajan Narayanan <quic_varada at quicinc.com>
>> +  - Sricharan R <quic_srichara at quicinc.com>
>> +  - Nitheesh Sekar <quic_nsekar at quicinc.com>
>> +
>> +description: |
>> +  This binding describes the Top Level Mode Multiplexer block found in the
>> +  IPQ5018 platform.
>> +
>> +properties:
>> +  compatible:
>> +    const: qcom,ipq5018-pinctrl
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +  interrupts:
>> +    description: Specifies the TLMM summary IRQ
>> +    maxItems: 1
>> +
>> +  interrupt-controller: true
>> +
>> +  '#interrupt-cells':
>> +    description:
>> +      Specifies the PIN numbers and Flags, as defined in defined in
>> +      include/dt-bindings/interrupt-controller/irq.h
>> +    const: 2
>> +
>> +  gpio-controller: true
>> +
>> +  '#gpio-cells':
>> +    description: Specifying the pin number and flags, as defined in
>> +      include/dt-bindings/gpio/gpio.h
>> +    const: 2
>> +
>> +  gpio-ranges:
>> +    maxItems: 1
>> +
>> +#PIN CONFIGURATION NODES
>> +patternProperties:
>> +  '-pinmux$':
>> +    type: object
>> +    description:
>> +      Pinctrl node's client devices use subnodes for desired pin configuration.
>> +      Client device subnodes use below standard properties.
>> +    $ref: "/schemas/pinctrl/pincfg-node.yaml"
> No need for quotes

  ok.


>> +
>> +    properties:
>> +      pins:
>> +        description:
>> +          List of gpio pins affected by the properties specified in this
>> +          subnode.
>> +        items:
>> +          oneOf:
>> +            - pattern: "^gpio([1-9]|[1-7][0-9]|80)$"
> Use consistent quotes in the patch: either ' or ". Don't mix.

  ok.


>> +        minItems: 1
>> +        maxItems: 4
>> +
>> +      function:
>> +        description:
>> +          Specify the alternative function to be configured for the specified
>> +          pins.
>> +        enum: [ atest_char, atest_char0, atest_char1, atest_char2, atest_char3,
>> +          audio_pdm0, audio_pdm1, audio_rxbclk, audio_rxd, audio_rxfsync,
>> +          audio_rxmclk, audio_txbclk, audio_txd, audio_txfsync, audio_txmclk,
>> +          blsp0_i2c, blsp0_spi, blsp0_uart0, blsp0_uart1, blsp1_i2c0,
>> +          blsp1_i2c1, blsp1_spi0, blsp1_spi1, blsp1_uart0, blsp1_uart1,
>> +          blsp1_uart2, blsp2_i2c0, blsp2_i2c1, blsp2_spi, blsp2_spi0,
>> +          blsp2_spi1, btss0, btss1, btss10, btss11, btss12, btss13, btss2,
>> +          btss3, btss4, btss5, btss6, btss7, btss8, btss9, burn0, burn1,
>> +          cri_trng, cri_trng0, cri_trng1, cxc_clk, cxc_data, dbg_out, eud_gpio,
>> +          gcc_plltest, gcc_tlmm, gpio, mac0, mac1, mdc, mdio, pcie0_clk,
>> +          pcie0_wake, pcie1_clk, pcie1_wake, pll_test, prng_rosc, pwm0, pwm1,
>> +          pwm2, pwm3, qdss_cti_trig_in_a0, qdss_cti_trig_in_a1,
>> +          qdss_cti_trig_in_b0, qdss_cti_trig_in_b1, qdss_cti_trig_out_a0,
>> +          qdss_cti_trig_out_a1, qdss_cti_trig_out_b0, qdss_cti_trig_out_b1,
>> +          qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
>> +          qdss_tracedata_a, qdss_tracedata_b, qspi_clk, qspi_cs, qspi0, qspi1,
>> +          qspi2, qspi3, reset_out, sdc1_clk, sdc1_cmd, sdc10, sdc11, sdc12,
>> +          sdc13, wci0, wci1, wci2, wci3, wci4, wci5, wci6, wci7, wsa_swrm,
>> +          wsi_clk3, wsi_data3, wsis_reset, xfem0, xfem1, xfem2, xfem3, xfem4,
>> +          xfem5, xfem6, xfem7 ]
>> +
>> +      drive-strength:
>> +        enum: [2, 4, 6, 8, 10, 12, 14, 16]
>> +        default: 2
>> +        description:
>> +          Selects the drive strength for the specified pins, in mA.
>> +
>> +      bias-pull-down: true
>> +
>> +      bias-pull-up: true
>> +
>> +      bias-disable: true
>> +
>> +      output-high: true
>> +
>> +      output-low: true
>> +
>> +    required:
>> +      - pins
>> +      - function
>> +
>> +    additionalProperties: false
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +  - interrupts
>> +  - interrupt-controller
>> +  - '#interrupt-cells'
>> +  - gpio-controller
>> +  - '#gpio-cells'
>> +  - gpio-ranges
> Missing allOf with reference to pinctrl schema.

   ok, will fix this.

Regards,
   Sricharan