[PATCH v13 02/15] PCI: imx6: Move PHY management functions together
Richard Zhu
hongxing.zhu at nxp.com
Fri Jun 17 03:31:01 PDT 2022
From: Bjorn Helgaas <bhelgaas at google.com>
Collect imx6_pcie_init_phy(), imx7d_pcie_wait_for_phy_pll_lock(), and
imx6_setup_phy_mpll() earlier with other PHY-related code. No functional
change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas at google.com>
Acked-by: Richard Zhu <hongxing.zhu at nxp.com>
---
drivers/pci/controller/dwc/pci-imx6.c | 256 +++++++++++++-------------
1 file changed, 128 insertions(+), 128 deletions(-)
diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index 8653ca8cbfb9..e63eb6380020 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -296,6 +296,134 @@ static int pcie_phy_write(struct imx6_pcie *imx6_pcie, int addr, u16 data)
return 0;
}
+static void imx6_pcie_init_phy(struct imx6_pcie *imx6_pcie)
+{
+ switch (imx6_pcie->drvdata->variant) {
+ case IMX8MM:
+ /*
+ * The PHY initialization had been done in the PHY
+ * driver, break here directly.
+ */
+ break;
+ case IMX8MQ:
+ /*
+ * TODO: Currently this code assumes external
+ * oscillator is being used
+ */
+ regmap_update_bits(imx6_pcie->iomuxc_gpr,
+ imx6_pcie_grp_offset(imx6_pcie),
+ IMX8MQ_GPR_PCIE_REF_USE_PAD,
+ IMX8MQ_GPR_PCIE_REF_USE_PAD);
+ /*
+ * Regarding the datasheet, the PCIE_VPH is suggested
+ * to be 1.8V. If the PCIE_VPH is supplied by 3.3V, the
+ * VREG_BYPASS should be cleared to zero.
+ */
+ if (imx6_pcie->vph &&
+ regulator_get_voltage(imx6_pcie->vph) > 3000000)
+ regmap_update_bits(imx6_pcie->iomuxc_gpr,
+ imx6_pcie_grp_offset(imx6_pcie),
+ IMX8MQ_GPR_PCIE_VREG_BYPASS,
+ 0);
+ break;
+ case IMX7D:
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX7D_GPR12_PCIE_PHY_REFCLK_SEL, 0);
+ break;
+ case IMX6SX:
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6SX_GPR12_PCIE_RX_EQ_MASK,
+ IMX6SX_GPR12_PCIE_RX_EQ_2);
+ fallthrough;
+ default:
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6Q_GPR12_PCIE_CTL_2, 0 << 10);
+
+ /* configure constant input signal to the pcie ctrl and phy */
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6Q_GPR12_LOS_LEVEL, 9 << 4);
+
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+ IMX6Q_GPR8_TX_DEEMPH_GEN1,
+ imx6_pcie->tx_deemph_gen1 << 0);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+ IMX6Q_GPR8_TX_DEEMPH_GEN2_3P5DB,
+ imx6_pcie->tx_deemph_gen2_3p5db << 6);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+ IMX6Q_GPR8_TX_DEEMPH_GEN2_6DB,
+ imx6_pcie->tx_deemph_gen2_6db << 12);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+ IMX6Q_GPR8_TX_SWING_FULL,
+ imx6_pcie->tx_swing_full << 18);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+ IMX6Q_GPR8_TX_SWING_LOW,
+ imx6_pcie->tx_swing_low << 25);
+ break;
+ }
+
+ imx6_pcie_configure_type(imx6_pcie);
+}
+
+static void imx7d_pcie_wait_for_phy_pll_lock(struct imx6_pcie *imx6_pcie)
+{
+ u32 val;
+ struct device *dev = imx6_pcie->pci->dev;
+
+ if (regmap_read_poll_timeout(imx6_pcie->iomuxc_gpr,
+ IOMUXC_GPR22, val,
+ val & IMX7D_GPR22_PCIE_PHY_PLL_LOCKED,
+ PHY_PLL_LOCK_WAIT_USLEEP_MAX,
+ PHY_PLL_LOCK_WAIT_TIMEOUT))
+ dev_err(dev, "PCIe PLL lock timeout\n");
+}
+
+static int imx6_setup_phy_mpll(struct imx6_pcie *imx6_pcie)
+{
+ unsigned long phy_rate = clk_get_rate(imx6_pcie->pcie_phy);
+ int mult, div;
+ u16 val;
+
+ if (!(imx6_pcie->drvdata->flags & IMX6_PCIE_FLAG_IMX6_PHY))
+ return 0;
+
+ switch (phy_rate) {
+ case 125000000:
+ /*
+ * The default settings of the MPLL are for a 125MHz input
+ * clock, so no need to reconfigure anything in that case.
+ */
+ return 0;
+ case 100000000:
+ mult = 25;
+ div = 0;
+ break;
+ case 200000000:
+ mult = 25;
+ div = 1;
+ break;
+ default:
+ dev_err(imx6_pcie->pci->dev,
+ "Unsupported PHY reference clock rate %lu\n", phy_rate);
+ return -EINVAL;
+ }
+
+ pcie_phy_read(imx6_pcie, PCIE_PHY_MPLL_OVRD_IN_LO, &val);
+ val &= ~(PCIE_PHY_MPLL_MULTIPLIER_MASK <<
+ PCIE_PHY_MPLL_MULTIPLIER_SHIFT);
+ val |= mult << PCIE_PHY_MPLL_MULTIPLIER_SHIFT;
+ val |= PCIE_PHY_MPLL_MULTIPLIER_OVRD;
+ pcie_phy_write(imx6_pcie, PCIE_PHY_MPLL_OVRD_IN_LO, val);
+
+ pcie_phy_read(imx6_pcie, PCIE_PHY_ATEOVRD, &val);
+ val &= ~(PCIE_PHY_ATEOVRD_REF_CLKDIV_MASK <<
+ PCIE_PHY_ATEOVRD_REF_CLKDIV_SHIFT);
+ val |= div << PCIE_PHY_ATEOVRD_REF_CLKDIV_SHIFT;
+ val |= PCIE_PHY_ATEOVRD_EN;
+ pcie_phy_write(imx6_pcie, PCIE_PHY_ATEOVRD, val);
+
+ return 0;
+}
+
static void imx6_pcie_reset_phy(struct imx6_pcie *imx6_pcie)
{
u16 tmp;
@@ -500,19 +628,6 @@ static int imx6_pcie_enable_ref_clk(struct imx6_pcie *imx6_pcie)
return ret;
}
-static void imx7d_pcie_wait_for_phy_pll_lock(struct imx6_pcie *imx6_pcie)
-{
- u32 val;
- struct device *dev = imx6_pcie->pci->dev;
-
- if (regmap_read_poll_timeout(imx6_pcie->iomuxc_gpr,
- IOMUXC_GPR22, val,
- val & IMX7D_GPR22_PCIE_PHY_PLL_LOCKED,
- PHY_PLL_LOCK_WAIT_USLEEP_MAX,
- PHY_PLL_LOCK_WAIT_TIMEOUT))
- dev_err(dev, "PCIe PLL lock timeout\n");
-}
-
static void imx6_pcie_deassert_core_reset(struct imx6_pcie *imx6_pcie)
{
struct dw_pcie *pci = imx6_pcie->pci;
@@ -635,121 +750,6 @@ static void imx6_pcie_deassert_core_reset(struct imx6_pcie *imx6_pcie)
}
}
-static void imx6_pcie_init_phy(struct imx6_pcie *imx6_pcie)
-{
- switch (imx6_pcie->drvdata->variant) {
- case IMX8MM:
- /*
- * The PHY initialization had been done in the PHY
- * driver, break here directly.
- */
- break;
- case IMX8MQ:
- /*
- * TODO: Currently this code assumes external
- * oscillator is being used
- */
- regmap_update_bits(imx6_pcie->iomuxc_gpr,
- imx6_pcie_grp_offset(imx6_pcie),
- IMX8MQ_GPR_PCIE_REF_USE_PAD,
- IMX8MQ_GPR_PCIE_REF_USE_PAD);
- /*
- * Regarding the datasheet, the PCIE_VPH is suggested
- * to be 1.8V. If the PCIE_VPH is supplied by 3.3V, the
- * VREG_BYPASS should be cleared to zero.
- */
- if (imx6_pcie->vph &&
- regulator_get_voltage(imx6_pcie->vph) > 3000000)
- regmap_update_bits(imx6_pcie->iomuxc_gpr,
- imx6_pcie_grp_offset(imx6_pcie),
- IMX8MQ_GPR_PCIE_VREG_BYPASS,
- 0);
- break;
- case IMX7D:
- regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
- IMX7D_GPR12_PCIE_PHY_REFCLK_SEL, 0);
- break;
- case IMX6SX:
- regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
- IMX6SX_GPR12_PCIE_RX_EQ_MASK,
- IMX6SX_GPR12_PCIE_RX_EQ_2);
- fallthrough;
- default:
- regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
- IMX6Q_GPR12_PCIE_CTL_2, 0 << 10);
-
- /* configure constant input signal to the pcie ctrl and phy */
- regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
- IMX6Q_GPR12_LOS_LEVEL, 9 << 4);
-
- regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
- IMX6Q_GPR8_TX_DEEMPH_GEN1,
- imx6_pcie->tx_deemph_gen1 << 0);
- regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
- IMX6Q_GPR8_TX_DEEMPH_GEN2_3P5DB,
- imx6_pcie->tx_deemph_gen2_3p5db << 6);
- regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
- IMX6Q_GPR8_TX_DEEMPH_GEN2_6DB,
- imx6_pcie->tx_deemph_gen2_6db << 12);
- regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
- IMX6Q_GPR8_TX_SWING_FULL,
- imx6_pcie->tx_swing_full << 18);
- regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
- IMX6Q_GPR8_TX_SWING_LOW,
- imx6_pcie->tx_swing_low << 25);
- break;
- }
-
- imx6_pcie_configure_type(imx6_pcie);
-}
-
-static int imx6_setup_phy_mpll(struct imx6_pcie *imx6_pcie)
-{
- unsigned long phy_rate = clk_get_rate(imx6_pcie->pcie_phy);
- int mult, div;
- u16 val;
-
- if (!(imx6_pcie->drvdata->flags & IMX6_PCIE_FLAG_IMX6_PHY))
- return 0;
-
- switch (phy_rate) {
- case 125000000:
- /*
- * The default settings of the MPLL are for a 125MHz input
- * clock, so no need to reconfigure anything in that case.
- */
- return 0;
- case 100000000:
- mult = 25;
- div = 0;
- break;
- case 200000000:
- mult = 25;
- div = 1;
- break;
- default:
- dev_err(imx6_pcie->pci->dev,
- "Unsupported PHY reference clock rate %lu\n", phy_rate);
- return -EINVAL;
- }
-
- pcie_phy_read(imx6_pcie, PCIE_PHY_MPLL_OVRD_IN_LO, &val);
- val &= ~(PCIE_PHY_MPLL_MULTIPLIER_MASK <<
- PCIE_PHY_MPLL_MULTIPLIER_SHIFT);
- val |= mult << PCIE_PHY_MPLL_MULTIPLIER_SHIFT;
- val |= PCIE_PHY_MPLL_MULTIPLIER_OVRD;
- pcie_phy_write(imx6_pcie, PCIE_PHY_MPLL_OVRD_IN_LO, val);
-
- pcie_phy_read(imx6_pcie, PCIE_PHY_ATEOVRD, &val);
- val &= ~(PCIE_PHY_ATEOVRD_REF_CLKDIV_MASK <<
- PCIE_PHY_ATEOVRD_REF_CLKDIV_SHIFT);
- val |= div << PCIE_PHY_ATEOVRD_REF_CLKDIV_SHIFT;
- val |= PCIE_PHY_ATEOVRD_EN;
- pcie_phy_write(imx6_pcie, PCIE_PHY_ATEOVRD, val);
-
- return 0;
-}
-
static int imx6_pcie_wait_for_speed_change(struct imx6_pcie *imx6_pcie)
{
struct dw_pcie *pci = imx6_pcie->pci;
--
2.25.1
More information about the linux-arm-kernel
mailing list