[PATCH v11 10/12] drm/mediatek: dpi: Add dpintf support

Rex-BC Chen rex-bc.chen at mediatek.com
Thu Jun 16 02:09:27 PDT 2022


On Tue, 2022-06-14 at 14:04 +0800, CK Hu wrote:
> Hi, Bo-Chen:
> 
> On Mon, 2022-06-13 at 14:48 +0800, Bo-Chen Chen wrote:
> > From: Guillaume Ranquet <granquet at baylibre.com>
> > 
> > dpintf is the displayport interface hardware unit. This unit is
> > similar
> > to dpi and can reuse most of the code.
> > 
> > This patch adds support for mt8195-dpintf to this dpi driver. Main
> > differences are:
> >  - Some features/functional components are not available for dpintf
> >    which are now excluded from code execution once is_dpintf is set
> >  - dpintf can and needs to choose between different clockdividers
> > based
> >    on the clockspeed. This is done by choosing a different clock
> > parent.
> >  - There are two additional clocks that need to be managed. These
> > are
> >    only set for dpintf and will be set to NULL if not supplied. The
> >    clk_* calls handle these as normal clocks then.
> >  - Some register contents differ slightly between the two
> > components.
> > To
> >    work around this I added register bits/masks with a DPINTF_
> > prefix
> >    and use them where different.
> > 
> > Based on a separate driver for dpintf created by
> > Jitao shi <jitao.shi at mediatek.com>.
> > 
> > Signed-off-by: Markus Schneider-Pargmann <msp at baylibre.com>
> > Signed-off-by: Guillaume Ranquet <granquet at baylibre.com>
> > [Bo-Chen: Modify reviewers' comments.]
> > Signed-off-by: Bo-Chen Chen <rex-bc.chen at mediatek.com>
> > ---
> >  drivers/gpu/drm/mediatek/mtk_dpi.c          | 115
> > ++++++++++++++++++--
> >  drivers/gpu/drm/mediatek/mtk_dpi_regs.h     |  13 +++
> >  drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.c |   4 +
> >  drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.h |   1 +
> >  drivers/gpu/drm/mediatek/mtk_drm_drv.c      |   3 +
> >  5 files changed, 126 insertions(+), 10 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c
> > b/drivers/gpu/drm/mediatek/mtk_dpi.c
> > index 6b8cf648a5b5..08c8f21b4421 100644
> > --- a/drivers/gpu/drm/mediatek/mtk_dpi.c
> > +++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
> > @@ -71,6 +71,7 @@ struct mtk_dpi {
> >  	void __iomem *regs;
> >  	struct device *dev;
> >  	struct clk *engine_clk;
> > +	struct clk *pll_gate_clk;
> 
> Separate clock part to an independent patch.
> 

Hello CK,

as previous reply, I will drop this clock.

> >  	struct clk *pixel_clk;
> >  	struct clk *tvd_clk;
> >  	int irq;
> > @@ -126,6 +127,7 @@ struct mtk_dpi_conf {
> >  	const u32 *output_fmts;
> >  	u32 num_output_fmts;
> >  	bool is_ck_de_pol;
> > +	bool is_dpintf;
> >  	bool swap_input_support;
> >  	/* Mask used for HWIDTH, HPORCH, VSYNC_WIDTH and VSYNC_PORCH
> > (no shift) */
> >  	u32 dimension_mask;
> > @@ -439,6 +441,8 @@ static void mtk_dpi_power_off(struct mtk_dpi
> > *dpi)
> >  	mtk_dpi_disable(dpi);
> >  	clk_disable_unprepare(dpi->pixel_clk);
> >  	clk_disable_unprepare(dpi->engine_clk);
> > +	clk_disable_unprepare(dpi->pll_gate_clk);
> > +	clk_disable_unprepare(dpi->tvd_clk);
> >  }
> >  
> >  static int mtk_dpi_power_on(struct mtk_dpi *dpi)
> > @@ -448,10 +452,23 @@ static int mtk_dpi_power_on(struct mtk_dpi
> > *dpi)
> >  	if (++dpi->refcount != 1)
> >  		return 0;
> >  
> > +	ret = clk_prepare_enable(dpi->tvd_clk);
> > +	if (ret) {
> > +		dev_err(dpi->dev, "Failed to enable tvd pll: %d\n",
> > ret);
> > +		goto err_refcount;
> > +	}
> > +
> >  	ret = clk_prepare_enable(dpi->engine_clk);
> >  	if (ret) {
> >  		dev_err(dpi->dev, "Failed to enable engine clock:
> > %d\n", ret);
> > -		goto err_refcount;
> > +		goto err_engine;
> > +	}
> > +
> > +	ret = clk_prepare_enable(dpi->pll_gate_clk);
> > +	if (ret) {
> > +		dev_err(dpi->dev,
> > +			"Failed to enable pll_gate_clk clock: %d\n",
> > ret);
> > +		goto err_ck_cg;
> >  	}
> >  
> >  	ret = clk_prepare_enable(dpi->pixel_clk);
> > @@ -467,7 +484,11 @@ static int mtk_dpi_power_on(struct mtk_dpi
> > *dpi)
> >  	return 0;
> >  
> >  err_pixel:
> > +	clk_disable_unprepare(dpi->pll_gate_clk);
> > +err_ck_cg:
> >  	clk_disable_unprepare(dpi->engine_clk);
> > +err_engine:
> > +	clk_disable_unprepare(dpi->tvd_clk);
> >  err_refcount:
> >  	dpi->refcount--;
> >  	return ret;
> > @@ -498,12 +519,16 @@ static int mtk_dpi_set_display_mode(struct
> > mtk_dpi *dpi,
> >  	pll_rate = clk_get_rate(dpi->tvd_clk);
> >  
> >  	vm.pixelclock = pll_rate / factor;
> > +
> > +	if (dpi->conf->is_dpintf)
> > +		vm.pixelclock /= 4;
> 
> Separate this to an independent patch and explain why do this.
> 

This patch is for support dpintf, It think it should be placed in this
patch. I will add comment for this.
/*
 * For dp_intf, we need to divide clock by 4 because it's
 * 4 pixels for one round while dpi is 1 pixel for one round.
 */

> > +
> >  	if ((dpi->output_fmt == MEDIA_BUS_FMT_RGB888_2X12_LE) ||
> > -	    (dpi->output_fmt == MEDIA_BUS_FMT_RGB888_2X12_BE))
> > +	    (dpi->output_fmt == MEDIA_BUS_FMT_RGB888_2X12_BE)) {
> >  		clk_set_rate(dpi->pixel_clk, vm.pixelclock * 2);
> > -	else
> > +	} else {
> 
> This modification is not necessary.
> 

ok.

> >  		clk_set_rate(dpi->pixel_clk, vm.pixelclock);
> > -
> > +	}
> >  
> >  	vm.pixelclock = clk_get_rate(dpi->pixel_clk);
> >  
> > @@ -516,9 +541,21 @@ static int mtk_dpi_set_display_mode(struct
> > mtk_dpi *dpi,
> >  			    MTK_DPI_POLARITY_FALLING :
> > MTK_DPI_POLARITY_RISING;
> >  	dpi_pol.vsync_pol = vm.flags & DISPLAY_FLAGS_VSYNC_HIGH ?
> >  			    MTK_DPI_POLARITY_FALLING :
> > MTK_DPI_POLARITY_RISING;
> > +
> 
> This modification is not necessary.
> 

ok.

> >  	hsync.sync_width = vm.hsync_len;
> >  	hsync.back_porch = vm.hback_porch;
> >  	hsync.front_porch = vm.hfront_porch;
> > +
> > +	/*
> > +	 * For dp_intf, we need to divide everything by 4 because it's
> > +	 * 4 pixels for one round while dpi is 1 pixel for one round.
> > +	 */
> > +	if (dpi->conf->is_dpintf) {
> 
> I this this should define dpi->conf->round_pixels rather than dpi-
> > conf->is_dpintf.
> > +		hsync.sync_width = vm.hsync_len / 4;
> > +		hsync.back_porch = vm.hback_porch / 4;
> > +		hsync.front_porch = vm.hfront_porch / 4;
> > +	}
> > +

I think is_dpintf is ok, it just for dpintf.

> >  	hsync.shift_half_line = false;
> >  	vsync_lodd.sync_width = vm.vsync_len;
> >  	vsync_lodd.back_porch = vm.vback_porch;
> > @@ -560,13 +597,20 @@ static int mtk_dpi_set_display_mode(struct
> > mtk_dpi *dpi,
> >  	mtk_dpi_config_channel_limit(dpi);
> >  	mtk_dpi_config_bit_num(dpi, dpi->bit_num);
> >  	mtk_dpi_config_channel_swap(dpi, dpi->channel_swap);
> > -	mtk_dpi_config_yc_map(dpi, dpi->yc_map);
> >  	mtk_dpi_config_color_format(dpi, dpi->color_format);
> > -	mtk_dpi_config_2n_h_fre(dpi);
> > -	mtk_dpi_dual_edge(dpi);
> > -	mtk_dpi_config_disable_edge(dpi);
> > +	if (dpi->conf->is_dpintf) {
> 
> Separate this to an independent patch and give a better config name
> rather than dpi->conf->is_dpintf.
> 

This patch is for dpintf. I think it's better to remain in this patch.

> > +		mtk_dpi_mask(dpi, DPI_CON, DPINTF_INPUT_2P_EN,
> > +			     DPINTF_INPUT_2P_EN);
> > +	} else {
> > +		mtk_dpi_config_yc_map(dpi, dpi->yc_map);
> > +		mtk_dpi_config_2n_h_fre(dpi);
> > +		mtk_dpi_dual_edge(dpi);
> > +		mtk_dpi_config_disable_edge(dpi);
> > +	}
> >  	mtk_dpi_sw_reset(dpi, false);
> >  
> > +	mtk_dpi_enable(dpi);
> 
> Why do this? If this is necessary, separate this to an independent
> patch.
> 

Yes, no need to do this.
I will drop this.

> > +
> >  	return 0;
> >  }
> >  
> > @@ -643,7 +687,10 @@ static int mtk_dpi_bridge_atomic_check(struct
> > drm_bridge *bridge,
> >  	dpi->bit_num = MTK_DPI_OUT_BIT_NUM_8BITS;
> >  	dpi->channel_swap = MTK_DPI_OUT_CHANNEL_SWAP_RGB;
> >  	dpi->yc_map = MTK_DPI_OUT_YC_MAP_RGB;
> > -	dpi->color_format = MTK_DPI_COLOR_FORMAT_RGB;
> > +	if (out_bus_format == MEDIA_BUS_FMT_YUYV8_1X16)
> > +		dpi->color_format =
> > MTK_DPI_COLOR_FORMAT_YCBCR_422_FULL;
> 
> Separate this to an independent patch.
> 

ok

> > +	else
> > +		dpi->color_format = MTK_DPI_COLOR_FORMAT_RGB;
> >  
> >  	return 0;
> >  }
> > @@ -688,7 +735,7 @@ mtk_dpi_bridge_mode_valid(struct drm_bridge
> > *bridge,
> >  {
> >  	struct mtk_dpi *dpi = bridge_to_dpi(bridge);
> >  
> > -	if (mode->clock > dpi->conf->max_clock_khz)
> > +	if (dpi->conf->max_clock_khz && mode->clock > dpi->conf-
> > > max_clock_khz)
> 
> Why dp_intf has no max_clock_khz?
> 

I will add max_clock_khz to 600MHz for dpintf

> Regards,
> CK
> 
> >  		return MODE_CLOCK_HIGH;
> >  
> >  	return MODE_OK;
> > @@ -802,6 +849,16 @@ static unsigned int
> > mt8183_calculate_factor(int
> > clock)
> >  		return 2;
> >  }
> >  
> > +static unsigned int mt8195_dpintf_calculate_factor(int clock)
> > +{
> > +	if (clock < 70000)
> > +		return 4;
> > +	else if (clock < 200000)
> > +		return 2;
> > +	else
> > +		return 1;
> > +}
> > +
> >  static const u32 mt8173_output_fmts[] = {
> >  	MEDIA_BUS_FMT_RGB888_1X24,
> >  };
> > @@ -811,6 +868,12 @@ static const u32 mt8183_output_fmts[] = {
> >  	MEDIA_BUS_FMT_RGB888_2X12_BE,
> >  };
> >  
> > +static const u32 mt8195_output_fmts[] = {
> > +	MEDIA_BUS_FMT_RGB888_1X24,
> > +	MEDIA_BUS_FMT_YUV8_1X24,
> > +	MEDIA_BUS_FMT_YUYV8_1X16,
> > +};
> > +
> >  static const struct mtk_dpi_yc_limit mtk_dpi_limit = {
> >  	.c_bottom = 0x0010,
> >  	.c_top = 0x0FE0,
> > @@ -818,6 +881,13 @@ static const struct mtk_dpi_yc_limit
> > mtk_dpi_limit = {
> >  	.y_top = 0x0FE0,
> >  };
> >  
> > +static const struct mtk_dpi_yc_limit mtk_dpintf_limit = {
> > +	.c_bottom = 0x0000,
> > +	.c_top = 0xFFF,
> > +	.y_bottom = 0x0000,
> > +	.y_top = 0xFFF,
> > +};
> > +
> >  static const struct mtk_dpi_conf mt8173_conf = {
> >  	.cal_factor = mt8173_calculate_factor,
> >  	.reg_h_fre_con = 0xe0,
> > @@ -883,6 +953,19 @@ static const struct mtk_dpi_conf mt8192_conf =
> > {
> >  	.limit = &mtk_dpi_limit,
> >  };
> >  
> > +static const struct mtk_dpi_conf mt8195_dpintf_conf = {
> > +	.cal_factor = mt8195_dpintf_calculate_factor,
> > +	.output_fmts = mt8195_output_fmts,
> > +	.num_output_fmts = ARRAY_SIZE(mt8195_output_fmts),
> > +	.is_dpintf = true,
> > +	.dimension_mask = DPINTF_HPW_MASK,
> > +	.hvsize_mask = DPINTF_HSIZE_MASK,
> > +	.channel_swap_shift = DPINTF_CH_SWAP,
> > +	.yuv422_en_bit = DPINTF_YUV422_EN,
> > +	.csc_enable_bit = DPINTF_CSC_ENABLE,
> > +	.limit = &mtk_dpintf_limit,
> > +};
> > +
> >  static int mtk_dpi_probe(struct platform_device *pdev)
> >  {
> >  	struct device *dev = &pdev->dev;
> > @@ -935,6 +1018,15 @@ static int mtk_dpi_probe(struct
> > platform_device
> > *pdev)
> >  		return ret;
> >  	}
> >  
> > +	dpi->pll_gate_clk = devm_clk_get_optional(dev, "pll_gate");
> > +	if (IS_ERR(dpi->pll_gate_clk)) {
> > +		ret = PTR_ERR(dpi->pll_gate_clk);
> > +		if (ret != -EPROBE_DEFER)
> > +			dev_err(dev, "Failed to get dpi ck cg clock:
> > %d\n", ret);
> > +
> > +		return ret;
> > +	}
> > +
> >  	dpi->pixel_clk = devm_clk_get(dev, "pixel");
> >  	if (IS_ERR(dpi->pixel_clk)) {
> >  		ret = PTR_ERR(dpi->pixel_clk);
> > @@ -1005,6 +1097,9 @@ static const struct of_device_id
> > mtk_dpi_of_ids[] = {
> >  	{ .compatible = "mediatek,mt8192-dpi",
> >  	  .data = &mt8192_conf,
> >  	},
> > +	{ .compatible = "mediatek,mt8195-dp_intf",
> > +	  .data = &mt8195_dpintf_conf,
> > +	},
> >  	{ },
> >  };
> >  MODULE_DEVICE_TABLE(of, mtk_dpi_of_ids);
> > diff --git a/drivers/gpu/drm/mediatek/mtk_dpi_regs.h
> > b/drivers/gpu/drm/mediatek/mtk_dpi_regs.h
> > index 3a02fabe1662..f7f0272dbd6a 100644
> > --- a/drivers/gpu/drm/mediatek/mtk_dpi_regs.h
> > +++ b/drivers/gpu/drm/mediatek/mtk_dpi_regs.h
> > @@ -40,9 +40,13 @@
> >  #define FAKE_DE_LEVEN			BIT(21)
> >  #define FAKE_DE_RODD			BIT(22)
> >  #define FAKE_DE_REVEN			BIT(23)
> > +#define DPINTF_YUV422_EN		BIT(24)
> > +#define DPINTF_CSC_ENABLE		BIT(26)
> > +#define DPINTF_INPUT_2P_EN		BIT(29)
> >  
> >  #define DPI_OUTPUT_SETTING	0x14
> >  #define CH_SWAP				0
> > +#define DPINTF_CH_SWAP			1
> >  #define CH_SWAP_MASK			(0x7 << 0)
> >  #define SWAP_RGB			0x00
> >  #define SWAP_GBR			0x01
> > @@ -80,8 +84,10 @@
> >  #define DPI_SIZE		0x18
> >  #define HSIZE				0
> >  #define HSIZE_MASK			(0x1FFF << 0)
> > +#define DPINTF_HSIZE_MASK		(0xFFFF << 0)
> >  #define VSIZE				16
> >  #define VSIZE_MASK			(0x1FFF << 16)
> > +#define DPINTF_VSIZE_MASK		(0xFFFF << 16)
> >  
> >  #define DPI_DDR_SETTING		0x1C
> >  #define DDR_EN				BIT(0)
> > @@ -93,24 +99,30 @@
> >  #define DPI_TGEN_HWIDTH		0x20
> >  #define HPW				0
> >  #define HPW_MASK			(0xFFF << 0)
> > +#define DPINTF_HPW_MASK			(0xFFFF << 0)
> >  
> >  #define DPI_TGEN_HPORCH		0x24
> >  #define HBP				0
> >  #define HBP_MASK			(0xFFF << 0)
> > +#define DPINTF_HBP_MASK			(0xFFFF << 0)
> >  #define HFP				16
> >  #define HFP_MASK			(0xFFF << 16)
> > +#define DPINTF_HFP_MASK			(0xFFFF << 16)
> >  
> >  #define DPI_TGEN_VWIDTH		0x28
> >  #define DPI_TGEN_VPORCH		0x2C
> >  
> >  #define VSYNC_WIDTH_SHIFT		0
> >  #define VSYNC_WIDTH_MASK		(0xFFF << 0)
> > +#define DPINTF_VSYNC_WIDTH_MASK		(0xFFFF << 0)
> >  #define VSYNC_HALF_LINE_SHIFT		16
> >  #define VSYNC_HALF_LINE_MASK		BIT(16)
> >  #define VSYNC_BACK_PORCH_SHIFT		0
> >  #define VSYNC_BACK_PORCH_MASK		(0xFFF << 0)
> > +#define DPINTF_VSYNC_BACK_PORCH_MASK	(0xFFFF << 0)
> >  #define VSYNC_FRONT_PORCH_SHIFT		16
> >  #define VSYNC_FRONT_PORCH_MASK		(0xFFF << 16)
> > +#define DPINTF_VSYNC_FRONT_PORCH_MASK	(0xFFFF << 16)
> >  
> >  #define DPI_BG_HCNTL		0x30
> >  #define BG_RIGHT			(0x1FFF << 0)
> > @@ -217,4 +229,5 @@
> >  
> >  #define EDGE_SEL_EN			BIT(5)
> >  #define H_FRE_2N			BIT(25)
> > +
> >  #endif /* __MTK_DPI_REGS_H */
> > diff --git a/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.c
> > b/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.c
> > index 2aab1e1eda36..5bef085714a1 100644
> > --- a/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.c
> > +++ b/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.c
> > @@ -427,6 +427,7 @@ static const char * const
> > mtk_ddp_comp_stem[MTK_DDP_COMP_TYPE_MAX] = {
> >  	[MTK_DISP_RDMA] = "rdma",
> >  	[MTK_DISP_UFOE] = "ufoe",
> >  	[MTK_DISP_WDMA] = "wdma",
> > +	[MTK_DP_INTF] = "dp-intf",
> >  	[MTK_DPI] = "dpi",
> >  	[MTK_DSI] = "dsi",
> >  };
> > @@ -450,6 +451,8 @@ static const struct mtk_ddp_comp_match
> > mtk_ddp_matches[DDP_COMPONENT_DRM_ID_MAX]
> >  	[DDP_COMPONENT_DRM_OVL_ADAPTOR]	= { MTK_DISP_OVL_ADAPTOR,	
> > 0, &ddp_ovl_adaptor },
> >  	[DDP_COMPONENT_DSC0]		= { MTK_DISP_DSC,		
> > 0, &ddp_dsc },
> >  	[DDP_COMPONENT_DSC1]		= { MTK_DISP_DSC,		
> > 1, &ddp_dsc },
> > +	[DDP_COMPONENT_DP_INTF0]	= { MTK_DP_INTF,		0,
> > &ddp_dpi },
> > +	[DDP_COMPONENT_DP_INTF1]	= { MTK_DP_INTF,		1,
> > &ddp_dpi },
> >  	[DDP_COMPONENT_DSI0]		= { MTK_DSI,			
> > 0, &ddp_dsi },
> >  	[DDP_COMPONENT_DSI1]		= { MTK_DSI,			
> > 1, &ddp_dsi },
> >  	[DDP_COMPONENT_DSI2]		= { MTK_DSI,			
> > 2, &ddp_dsi },
> > @@ -575,6 +578,7 @@ int mtk_ddp_comp_init(struct device_node *node,
> > struct mtk_ddp_comp *comp,
> >  	    type == MTK_DISP_PWM ||
> >  	    type == MTK_DISP_RDMA ||
> >  	    type == MTK_DPI ||
> > +	    type == MTK_DP_INTF ||
> >  	    type == MTK_DSI)
> >  		return 0;
> >  
> > diff --git a/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.h
> > b/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.h
> > index af9a6671f9c4..3084cc4e2830 100644
> > --- a/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.h
> > +++ b/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.h
> > @@ -38,6 +38,7 @@ enum mtk_ddp_comp_type {
> >  	MTK_DISP_UFOE,
> >  	MTK_DISP_WDMA,
> >  	MTK_DPI,
> > +	MTK_DP_INTF,
> >  	MTK_DSI,
> >  	MTK_DDP_COMP_TYPE_MAX,
> >  };
> > diff --git a/drivers/gpu/drm/mediatek/mtk_drm_drv.c
> > b/drivers/gpu/drm/mediatek/mtk_drm_drv.c
> > index 78e79c8449c8..3b885ad61ac3 100644
> > --- a/drivers/gpu/drm/mediatek/mtk_drm_drv.c
> > +++ b/drivers/gpu/drm/mediatek/mtk_drm_drv.c
> > @@ -788,6 +788,8 @@ static const struct of_device_id
> > mtk_ddp_comp_dt_ids[] = {
> >  	  .data = (void *)MTK_DPI },
> >  	{ .compatible = "mediatek,mt8192-dpi",
> >  	  .data = (void *)MTK_DPI },
> > +	{ .compatible = "mediatek,mt8195-dp_intf",
> > +	  .data = (void *)MTK_DP_INTF },
> >  	{ .compatible = "mediatek,mt2701-dsi",
> >  	  .data = (void *)MTK_DSI },
> >  	{ .compatible = "mediatek,mt8173-dsi",
> > @@ -931,6 +933,7 @@ static int mtk_drm_probe(struct platform_device
> > *pdev)
> >  		    comp_type == MTK_DISP_OVL_2L ||
> >  		    comp_type == MTK_DISP_OVL_ADAPTOR ||
> >  		    comp_type == MTK_DISP_RDMA ||
> > +		    comp_type == MTK_DP_INTF ||
> >  		    comp_type == MTK_DPI ||
> >  		    comp_type == MTK_DSI) {
> >  			dev_info(dev, "Adding component match for
> > %pOF\n",
> 
> 




More information about the linux-arm-kernel mailing list