[PATCH v2 15/18] ARM: dts: imx6q-apalis: Add support for Toradex Ixora V1.2 carrier boards
Max Krummenacher
max.oss.09 at gmail.com
Wed Jun 15 04:50:03 PDT 2022
From: Max Krummenacher <max.krummenacher at toradex.com>
The Ixora V1.2 carrier board adds SW relevant new features compared to
the V1.1 version.
- An I2C EEPROM is added.
- The SD card slot got a switchable 3.3V supply.
- Pull ups on the SD card signals are not assembled to faciliate 1.8V
speed modes.
- The CAN transceivers got a switchable 3.3V supply.
Add a new device tree and, as the differences are so small rework the
device tree for V1.1 to include the V1.2 device tree and adjust as
needed.
Drop adding the toradex,apalis_imx6q-ixora to the dtb compatible to
adhere to the binding yaml document.
Signed-off-by: Max Krummenacher <max.krummenacher at toradex.com>
---
Changes in v2:
- removed gpio-keys node. This has been moved to the SoM dtsi in v2
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts | 178 +----------
arch/arm/boot/dts/imx6q-apalis-ixora-v1.2.dts | 276 ++++++++++++++++++
3 files changed, 289 insertions(+), 166 deletions(-)
create mode 100644 arch/arm/boot/dts/imx6q-apalis-ixora-v1.2.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d3f1e3075178..428d758fc411 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -550,6 +550,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-apalis-eval.dtb \
imx6q-apalis-ixora.dtb \
imx6q-apalis-ixora-v1.1.dtb \
+ imx6q-apalis-ixora-v1.2.dtb \
imx6q-apf6dev.dtb \
imx6q-arm2.dtb \
imx6q-b450v3.dtb \
diff --git a/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts b/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
index 2d0324103804..44637d606e61 100644
--- a/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
+++ b/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
@@ -5,187 +5,33 @@
* Copyright 2011 Linaro Ltd.
*/
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include "imx6q.dtsi"
-#include "imx6qdl-apalis.dtsi"
+#include "imx6q-apalis-ixora-v1.2.dts"
/ {
model = "Toradex Apalis iMX6Q/D Module on Ixora Carrier Board V1.1";
- compatible = "toradex,apalis_imx6q-ixora-v1.1",
- "toradex,apalis_imx6q-ixora", "toradex,apalis_imx6q",
+ compatible = "toradex,apalis_imx6q-ixora-v1.1", "toradex,apalis_imx6q",
"fsl,imx6q";
- aliases {
- i2c0 = &i2c1;
- i2c1 = &i2c3;
- i2c2 = &i2c2;
- rtc0 = &rtc_i2c;
- rtc1 = &snvs_rtc;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpio_keys>;
-
- wakeup {
- label = "Wake-Up";
- gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WAKEUP>;
- debounce-interval = <10>;
- wakeup-source;
- };
- };
-
- leds {
- compatible = "gpio-leds";
-
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_leds_ixora>;
-
- led4-green {
- label = "LED_4_GREEN";
- gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
- };
- led4-red {
- label = "LED_4_RED";
- gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
- };
-
- led5-green {
- label = "LED_5_GREEN";
- gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
- };
-
- led5-red {
- label = "LED_5_RED";
- gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
- };
- };
};
+/delete-node/ &eeprom;
+/delete-node/ ®_3v3_vmmc;
+/delete-node/ ®_can1_supply;
+/delete-node/ ®_can2_supply;
+
&can1 {
- status = "okay";
+ /delete-property/ xceiver-supply;
};
&can2 {
- status = "okay";
-};
-
-/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
-&i2c1 {
- status = "okay";
-
- /* M41T0M6 real time clock on carrier board */
- rtc_i2c: rtc at 68 {
- compatible = "st,m41t0";
- reg = <0x68>;
- };
-};
-
-/*
- * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
- * board)
- */
-&i2c3 {
- status = "okay";
-};
-
-&pcie {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_reset_moci>;
- /* active-high meaning opposite of regular PERST# active-low polarity */
- reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
- reset-gpio-active-high;
- status = "okay";
-};
-
-&pwm1 {
- status = "okay";
-};
-
-&pwm2 {
- status = "okay";
-};
-
-&pwm3 {
- status = "okay";
-};
-
-&pwm4 {
- status = "okay";
-};
-
-®_usb_otg_vbus {
- status = "okay";
-};
-
-®_usb_host_vbus {
- status = "okay";
-};
-
-&sata {
- status = "okay";
-};
-
-&sound_spdif {
- status = "okay";
-};
-
-&spdif {
- status = "okay";
-};
-
-&uart1 {
- status = "okay";
-};
-
-&uart2 {
- status = "okay";
-};
-
-&uart4 {
- status = "okay";
-};
-
-&uart5 {
- status = "okay";
-};
-
-&usbh1 {
- vbus-supply = <®_usb_host_vbus>;
- status = "okay";
-};
-
-&usbotg {
- vbus-supply = <®_usb_otg_vbus>;
- status = "okay";
+ /delete-property/ xceiver-supply;
};
/* MMC1 */
&usdhc1 {
+ /delete-property/ cap-power-off-card;
+ /delete-property/ pinctrl-1;
+ /delete-property/ vmmc-supply;
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_mmc_cd>;
- bus-width = <4>;
- status = "okay";
-};
-
-&iomuxc {
- pinctrl_leds_ixora: ledsixoragrp {
- fsl,pins = <
- MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
- MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0
- MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
- MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
- >;
- };
};
diff --git a/arch/arm/boot/dts/imx6q-apalis-ixora-v1.2.dts b/arch/arm/boot/dts/imx6q-apalis-ixora-v1.2.dts
new file mode 100644
index 000000000000..f9f7d99bd4db
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-apalis-ixora-v1.2.dts
@@ -0,0 +1,276 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2014-2022 Toradex
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6q.dtsi"
+#include "imx6qdl-apalis.dtsi"
+
+/ {
+ model = "Toradex Apalis iMX6Q/D Module on Ixora Carrier Board V1.2";
+ compatible = "toradex,apalis_imx6q-ixora-v1.2", "toradex,apalis_imx6q",
+ "fsl,imx6q";
+
+ aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c3;
+ i2c2 = &i2c2;
+ rtc0 = &rtc_i2c;
+ rtc1 = &snvs_rtc;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds_ixora>;
+
+ led4-green {
+ gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+ label = "LED_4_GREEN";
+ };
+
+ led4-red {
+ gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+ label = "LED_4_RED";
+ };
+
+ led5-green {
+ gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+ label = "LED_5_GREEN";
+ };
+
+ led5-red {
+ gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ label = "LED_5_RED";
+ };
+ };
+
+ reg_3v3_vmmc: regulator-3v3-vmmc {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enable_3v3_vmmc>;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "3v3_vmmc";
+ startup-delay-us = <100>;
+ };
+
+ reg_can1_supply: regulator-can1-supply {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enable_can1_power>;
+ regulator-name = "can1_supply";
+ };
+
+ reg_can2_supply: regulator-can2-supply {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enable_can2_power>;
+ regulator-name = "can2_supply";
+ };
+};
+
+&can1 {
+ xceiver-supply = <®_can1_supply>;
+ status = "okay";
+};
+
+&can2 {
+ xceiver-supply = <®_can2_supply>;
+ status = "okay";
+};
+
+&gpio1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart24_forceoff>;
+
+ /*
+ * uart-2-4-on-x21-enable-hog enables the UART transceiver for Apalis
+ * UART2 and UART3. If one wants to disable the transceiver force
+ * the GPIO to output-low, if one wants to control the transceiver
+ * from user space delete the hog node.
+ */
+ uart-2-4-on-x21-enable-hog {
+ gpio-hog;
+ gpios = <11 GPIO_ACTIVE_HIGH>; /* MXM3 180 */
+ output-high;
+ };
+};
+
+/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
+&i2c1 {
+ status = "okay";
+
+ /* M41T0M6 real time clock on carrier board */
+ rtc_i2c: rtc at 68 {
+ compatible = "st,m41t0";
+ reg = <0x68>;
+ };
+
+ eeprom: eeprom at 50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+};
+
+/*
+ * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
+ * board)
+ */
+&i2c3 {
+ status = "okay";
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reset_moci>;
+ /* active-high meaning opposite of regular PERST# active-low polarity */
+ reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ reset-gpio-active-high;
+ status = "okay";
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&pwm3 {
+ status = "okay";
+};
+
+&pwm4 {
+ status = "okay";
+};
+
+®_usb_host_vbus {
+ status = "okay";
+};
+
+®_usb_otg_vbus {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&sound_spdif {
+ status = "okay";
+};
+
+&spdif {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+};
+
+&uart5 {
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_host_vbus>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ status = "okay";
+};
+
+/* MMC1 */
+&usdhc1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_mmc_cd>;
+ pinctrl-1 = <&pinctrl_usdhc1_4bit_sleep &pinctrl_mmc_cd_sleep>;
+ bus-width = <4>;
+ cap-power-off-card;
+ vmmc-supply = <®_3v3_vmmc>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_enable_3v3_vmmc: enable3v3vmmcgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_enable_can1_power: enablecan1powergrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0
+ >;
+ };
+
+ pinctrl_enable_can2_power: enablecan2powergrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_DA15__GPIO3_IO15 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart24_forceoff: uart24forceoffgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__GPIO1_IO11 0x1b0b0
+ >;
+ };
+
+ pinctrl_leds_ixora: ledsixoragrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
+ MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0
+ MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
+ MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
+ >;
+ };
+
+ pinctrl_mmc_cd_sleep: mmccdslpgrp {
+ fsl,pins = <
+ /* MMC1 CD */
+ MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x0
+ >;
+ };
+
+ pinctrl_usdhc1_4bit_sleep: usdhc1-4bitslpgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x3000
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x3000
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x3000
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x3000
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x3000
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x3000
+ >;
+ };
+};
--
2.20.1
More information about the linux-arm-kernel
mailing list