[PATCH v9 2/3] arm64: dts: marvell: Add Armada 98DX2530 SoC and RD-AC5X board
Vadym Kochan
vadym.kochan at plvision.eu
Mon Jun 13 15:53:23 PDT 2022
From: Chris Packham <chris.packham at alliedtelesis.co.nz>
The 98DX2530 SoC is the Control and Management CPU integrated into
the Marvell 98DX25xx and 98DX35xx series of switch chip (internally
referred to as AlleyCat5 and AlleyCat5X).
These files have been taken from the Marvell SDK and lightly cleaned
up with the License and copyright retained.
Signed-off-by: Chris Packham <chris.packham at alliedtelesis.co.nz>
Signed-off-by: Vadym Kochan <vadym.kochan at plvision.eu>
---
Notes:
The Marvell SDK has a number of new compatible strings. I've brought
through some of the drivers or where possible used an in-tree
alternative (e.g. there is SDK code for a ac5-gpio but two instances of
the existing marvell,orion-gpio seems to cover what is needed if you use
an appropriate binding). I expect that there will a new series of
patches when I get some different hardware (or additions to this series
depending on if/when it lands).
Changes in v9 (proposed by Marvell):
It was discussed with Chris that Marvell will add some changes:
1) Rename "armada-" prefix in dts(i) file names to ac5, because
Armada has not much common with AC5 SoC.
2) Add clock fixes:
- rename core_clock to cnm_clock
- remove axi_clock
- change cnm_clock to 325MHZ
- use cnm_clock for the UART
Changes in v8:
- Remove unnecessary clock-frequency property on armv8-timer
- Remove unnecessary redistributor-stride property on gic
- Add GIC_SPI interrupts for gpios
Changes in v7:
- Add missing compatible on usb1
- Add "rd-ac5x" compatible for board
- Move aliases to board dts
- Move board specific usb info to board dts
- Consolidate usb1 board settings and remove unnecessary compatible
- Add Allied Telesis copyright
- Rename files after mailng-list discussion
Changes in v6:
- Move CPU nodes above the SoC (Krzysztof)
- Minor formatting clean ups (Krzysztof)
- Run through `make dtbs_check`
- Move gic nodes inside SoC
- Group clocks under a clock node
Changes in v5:
- add #{address,size}-cells property to i2c nodes
- make i2c nodes disabled in the SoC and enable them in the board
- add interrupt controller attributes to gpio nodes
- Move fixed-clock nodes up a level and remove unnecessary @0
Changes in v4:
- use 'phy-handle' instead of 'phy'
- move status="okay" on usb nodes to board dts
- Add review from Andrew
Changes in v3:
- Move memory node to board
- Use single digit reg value for phy address
- Remove MMC node (driver needs work)
- Remove syscon & simple-mfd for pinctrl
Changes in v2:
- Make pinctrl a child node of a syscon node
- Use marvell,armada-8k-gpio instead of orion-gpio
- Remove nand peripheral. The Marvell SDK does have some changes for the
ac5-nand-controller but I currently lack hardware with NAND fitted so
I can't test it right now. I've therefore chosen to omit the node and
not attempted to bring in the driver or binding.
- Remove pcie peripheral. Again there are changes in the SDK and I have
no way of testing them.
- Remove prestera node.
- Remove "marvell,ac5-ehci" compatible from USB node as
"marvell,orion-ehci" is sufficient
- Remove watchdog node. There is a buggy driver for the ac5 watchdog in
the SDK but it needs some work so I've dropped the node for now.
arch/arm64/boot/dts/marvell/Makefile | 1 +
arch/arm64/boot/dts/marvell/ac5-98dx25xx.dtsi | 291 ++++++++++++++++++
.../boot/dts/marvell/ac5-98dx35xx-rd.dts | 101 ++++++
arch/arm64/boot/dts/marvell/ac5-98dx35xx.dtsi | 13 +
4 files changed, 406 insertions(+)
create mode 100644 arch/arm64/boot/dts/marvell/ac5-98dx25xx.dtsi
create mode 100644 arch/arm64/boot/dts/marvell/ac5-98dx35xx-rd.dts
create mode 100644 arch/arm64/boot/dts/marvell/ac5-98dx35xx.dtsi
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 1c794cdcb8e6..b6d493e34dc5 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -24,3 +24,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += ac5-98dx35xx-rd.dtb
diff --git a/arch/arm64/boot/dts/marvell/ac5-98dx25xx.dtsi b/arch/arm64/boot/dts/marvell/ac5-98dx25xx.dtsi
new file mode 100644
index 000000000000..cf0b4a7de323
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/ac5-98dx25xx.dtsi
@@ -0,0 +1,291 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree For AC5.
+ *
+ * Copyright (C) 2021 Marvell
+ * Copyright (C) 2022 Allied Telesis Labs
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ model = "Marvell AC5 SoC";
+ compatible = "marvell,ac5";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ };
+ };
+
+ cpu0: cpu at 0 {
+ device_type = "cpu";
+ compatible = "arm,armv8";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu1: cpu at 1 {
+ device_type = "cpu";
+ compatible = "arm,armv8";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ l2: l2-cache {
+ compatible = "cache";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_PPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <GIC_PPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ dma-ranges;
+
+ internal-regs at 7f000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ /* 16M internal register @ 0x7f00_0000 */
+ ranges = <0x0 0x0 0x7f000000 0x1000000>;
+ dma-coherent;
+
+ uart0: serial at 12000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x12000 0x100>;
+ reg-shift = <2>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ reg-io-width = <1>;
+ clocks = <&cnm_clock>;
+ status = "okay";
+ };
+
+ mdio: mdio at 22004 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "marvell,orion-mdio";
+ reg = <0x22004 0x4>;
+ clocks = <&cnm_clock>;
+ };
+
+ i2c0: i2c at 11000{
+ compatible = "marvell,mv78230-i2c";
+ reg = <0x11000 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ clocks = <&cnm_clock>;
+ clock-names = "core";
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency=<100000>;
+
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-1 = <&i2c0_gpio>;
+ scl_gpio = <&gpio0 26 GPIO_ACTIVE_HIGH>;
+ sda_gpio = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+ status = "disabled";
+ };
+
+ i2c1: i2c at 11100{
+ compatible = "marvell,mv78230-i2c";
+ reg = <0x11100 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ clocks = <&cnm_clock>;
+ clock-names = "core";
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency=<100000>;
+
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&i2c1_pins>;
+ pinctrl-1 = <&i2c1_gpio>;
+ scl_gpio = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+ sda_gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+ status = "disabled";
+ };
+
+ gpio0: gpio at 18100 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18100 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pinctrl0 0 0 32>;
+ marvell,pwm-offset = <0x1f0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpio1: gpio at 18140 {
+ reg = <0x18140 0x40>;
+ compatible = "marvell,orion-gpio";
+ ngpios = <14>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pinctrl0 0 32 14>;
+ marvell,pwm-offset = <0x1f0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ /*
+ * Dedicated section for devices behind 32bit controllers so we
+ * can configure specific DMA mapping for them
+ */
+ behind-32bit-controller at 7f000000 {
+ compatible = "simple-bus";
+ #address-cells = <0x2>;
+ #size-cells = <0x2>;
+ ranges = <0x0 0x0 0x0 0x7f000000 0x0 0x1000000>;
+ /* Host phy ram starts at 0x200M */
+ dma-ranges = <0x0 0x0 0x2 0x0 0x1 0x0>;
+ dma-coherent;
+
+ eth0: ethernet at 20000 {
+ compatible = "marvell,armada-ac5-neta";
+ reg = <0x0 0x20000 0x0 0x4000>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cnm_clock>;
+ phy-mode = "sgmii";
+ status = "disabled";
+ };
+
+ eth1: ethernet at 24000 {
+ compatible = "marvell,armada-ac5-neta";
+ reg = <0x0 0x24000 0x0 0x4000>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cnm_clock>;
+ phy-mode = "sgmii";
+ status = "disabled";
+ };
+
+ usb0: usb at 80000 {
+ compatible = "marvell,orion-ehci";
+ reg = <0x0 0x80000 0x0 0x500>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ usb1: usb at a0000 {
+ compatible = "marvell,orion-ehci";
+ reg = <0x0 0xa0000 0x0 0x500>;
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+ };
+
+ pinctrl0: pinctrl at 80020100 {
+ compatible = "marvell,ac5-pinctrl";
+ reg = <0 0x80020100 0 0x20>;
+
+ i2c0_pins: i2c0-pins {
+ marvell,pins = "mpp26", "mpp27";
+ marvell,function = "i2c0";
+ };
+
+ i2c0_gpio: i2c0-gpio-pins {
+ marvell,pins = "mpp26", "mpp27";
+ marvell,function = "gpio";
+ };
+
+ i2c1_pins: i2c1-pins {
+ marvell,pins = "mpp20", "mpp21";
+ marvell,function = "i2c1";
+ };
+
+ i2c1_gpio: i2c1-gpio-pins {
+ marvell,pins = "mpp20", "mpp21";
+ marvell,function = "i2c1";
+ };
+ };
+
+ spi0: spi at 805a0000 {
+ compatible = "marvell,armada-3700-spi";
+ reg = <0x0 0x805a0000 0x0 0x50>;
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ clocks = <&spi_clock>;
+ interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+ num-cs = <1>;
+ status = "disabled";
+ };
+
+ spi1: spi at 805a8000 {
+ compatible = "marvell,armada-3700-spi";
+ reg = <0x0 0x805a8000 0x0 0x50>;
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ clocks = <&spi_clock>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+ num-cs = <1>;
+ status = "disabled";
+ };
+
+ gic: interrupt-controller at 80600000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x0 0x80600000 0x0 0x10000>, /* GICD */
+ <0x0 0x80660000 0x0 0x40000>; /* GICR */
+ interrupts = <GIC_PPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ clocks {
+ cnm_clock: core-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <325000000>;
+ };
+
+ spi_clock: spi-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <200000000>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/marvell/ac5-98dx35xx-rd.dts b/arch/arm64/boot/dts/marvell/ac5-98dx35xx-rd.dts
new file mode 100644
index 000000000000..f0ebdb84eec9
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/ac5-98dx35xx-rd.dts
@@ -0,0 +1,101 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree For RD-AC5X.
+ *
+ * Copyright (C) 2021 Marvell
+ * Copyright (C) 2022 Allied Telesis Labs
+ */
+/*
+ * Device Tree file for Marvell Alleycat 5X development board
+ * This board file supports the B configuration of the board
+ */
+
+/dts-v1/;
+
+#include "ac5-98dx35xx.dtsi"
+
+/ {
+ model = "Marvell RD-AC5X Board";
+ compatible = "marvell,rd-ac5x", "marvell,ac5x", "marvell,ac5";
+
+ aliases {
+ serial0 = &uart0;
+ spiflash0 = &spiflash0;
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ ethernet0 = ð0;
+ ethernet1 = ð1;
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x2 0x00000000 0x0 0x40000000>;
+ };
+
+ usb1phy: usb-phy {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+};
+
+&mdio {
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+ð0 {
+ status = "okay";
+ phy-handle = <&phy0>;
+};
+
+/* USB0 is a host USB */
+&usb0 {
+ status = "okay";
+};
+
+/* USB1 is a peripheral USB */
+&usb1 {
+ status = "okay";
+ phys = <&usb1phy>;
+ phy-names = "usb-phy";
+ dr_mode = "peripheral";
+};
+
+&spi0 {
+ status = "okay";
+
+ spiflash0: flash at 0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <50000000>;
+ spi-tx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
+ spi-rx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
+ reg = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "spi_flash_part0";
+ reg = <0x0 0x800000>;
+ };
+
+ parition at 1 {
+ label = "spi_flash_part1";
+ reg = <0x800000 0x700000>;
+ };
+
+ parition at 2 {
+ label = "spi_flash_part2";
+ reg = <0xF00000 0x100000>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/marvell/ac5-98dx35xx.dtsi b/arch/arm64/boot/dts/marvell/ac5-98dx35xx.dtsi
new file mode 100644
index 000000000000..50d464d9d2f4
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/ac5-98dx35xx.dtsi
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree For AC5X.
+ *
+ * Copyright (C) 2022 Allied Telesis Labs
+ */
+
+#include "ac5-98dx25xx.dtsi"
+
+/ {
+ model = "Marvell AC5X SoC";
+ compatible = "marvell,ac5x", "marvell,ac5";
+};
--
2.17.1
More information about the linux-arm-kernel
mailing list