[RFC PATCH v1 5/5] ARM64: verdin-imx8mm: use regulator power domain to model sleep-moci

[Max Krummenacher]

From: Max Krummenacher <max.krummenacher at toradex.com>

The Verdin CTRL_SLEEP_MOCI# pin signals the carrier board that the module
is in sleep and it may switch off unneeded power.

Control this pin with a regulator power domain controller which uses a
fixed regulator with a gpio enable.

Signed-off-by: Max Krummenacher <max.krummenacher at toradex.com>

---

 .../dts/freescale/imx8mm-verdin-dahlia.dtsi   |  1 +
 .../boot/dts/freescale/imx8mm-verdin-dev.dtsi |  2 ++
 .../boot/dts/freescale/imx8mm-verdin.dtsi     | 35 +++++++++++++------
 3 files changed, 28 insertions(+), 10 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
index c2a5c2f7b204..03416dc593d8 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
@@ -92,6 +92,7 @@
 
 /* Verdin PCIE_1 */
 &pcie0 {
+	power-domains = <&pd_sleep_moci>;
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
index 73cc3fafa018..f887b907fdde 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
@@ -50,6 +50,7 @@
 	/* Audio Codec */
 	nau8822_1a: audio-codec at 1a {
 		compatible = "nuvoton,nau8822";
+		power-domains = <&pd_sleep_moci>;
 		reg = <0x1a>;
 	};
 };
@@ -59,6 +60,7 @@
 	linux,rs485-enabled-at-boot-time;
 	rs485-rts-active-low;
 	rs485-rx-during-tx;
+	power-domains = <&pd_sleep_moci>;
 };
 
 /* Limit frequency on dev board due to long traces and bad signal integrity */
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi
index eafa88d980b3..b5daa8f83bef 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi
@@ -53,6 +53,14 @@
 		};
 	};
 
+	pd_sleep_moci: power-domain-sleep-moci {
+		compatible = "regulator-pm-pd";
+		label = "pd_sleep_moci";
+		power-domains = <&pgc_pcie>;
+		power-supply = <&reg_sleep_moci>;
+		#power-domain-cells = <0>;
+	};
+
 	/* Carrier Board Supplies */
 	reg_1p8v: regulator-1p8v {
 		compatible = "regulator-fixed";
@@ -90,6 +98,19 @@
 		startup-delay-us = <200000>;
 	};
 
+	reg_sleep_moci: regulator-sleep-moci {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		off-on-delay = <2000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ctrl_sleep_moci>;
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "CTRL_SLEEP_MOCI#";
+		startup-delay-us = <2000>;
+	};
+
 	reg_usb_otg1_vbus: regulator-usb-otg1 {
 		compatible = "regulator-fixed";
 		enable-active-high;
@@ -109,6 +130,7 @@
 		gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_reg_usb2_en>;
+		power-domains = <&pd_sleep_moci>;
 		regulator-max-microvolt = <5000000>;
 		regulator-min-microvolt = <5000000>;
 		regulator-name = "USB_2_EN";
@@ -198,6 +220,7 @@
 		interrupts-extended = <&gpio1 6 IRQ_TYPE_EDGE_FALLING>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_can1_int>;
+		power-domains = <&pd_sleep_moci>;
 		reg = <0>;
 		spi-max-frequency = <8500000>;
 	};
@@ -305,16 +328,6 @@
 			  "SODIMM_212",
 			  "SODIMM_151",
 			  "SODIMM_153";
-
-	ctrl-sleep-moci-hog {
-		gpio-hog;
-		/* Verdin CTRL_SLEEP_MOCI# (SODIMM 256) */
-		gpios = <1 GPIO_ACTIVE_HIGH>;
-		line-name = "CTRL_SLEEP_MOCI#";
-		output-high;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ctrl_sleep_moci>;
-	};
 };
 
 /* On-module I2C */
@@ -560,6 +573,7 @@
 		enable-gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_10_dsi>;
+		power-domains = <&pd_sleep_moci>;
 		reg = <0x2c>;
 		status = "disabled";
 	};
@@ -576,6 +590,7 @@
 		compatible = "lontium,lt8912b";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_10_dsi>, <&pinctrl_pwm_3_dsi_hpd_gpio>;
+		power-domains = <&pd_sleep_moci>;
 		reg = <0x48>;
 		/* Verdin GPIO_9_DSI (LT8912 INT, SODIMM 17, unused) */
 		/* Verdin GPIO_10_DSI (SODIMM 21) */
-- 
2.20.1