[PATCH 2/7] dt-bindings: phy: add binding document for Allwinner F1C100s USB PHY

Icenowy Zheng uwu at icenowy.me
Wed Jun 8 07:52:52 PDT 2022


在 2022-06-08星期三的 08:49 -0600,Rob Herring写道:
> On Wed, Jun 08, 2022 at 03:04:47PM +0800, Icenowy Zheng wrote:
> > Allwinner F1C100s has the most simple USB PHY among all Allwinner
> > SoCs,
> > because it has only one OTG USB controller, no host-only OHCI/EHCI
> > controllers.
> > 
> > Add a binding document for it.
> > 
> > Signed-off-by: Icenowy Zheng <uwu at icenowy.me>
> > ---
> >  .../phy/allwinner,suniv-f1c100s-usb-phy.yaml  | 83
> > +++++++++++++++++++
> >  1 file changed, 83 insertions(+)
> >  create mode 100644
> > Documentation/devicetree/bindings/phy/allwinner,suniv-f1c100s-usb-
> > phy.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/phy/allwinner,suniv-
> > f1c100s-usb-phy.yaml
> > b/Documentation/devicetree/bindings/phy/allwinner,suniv-f1c100s-
> > usb-phy.yaml
> > new file mode 100644
> > index 000000000000..180fa8840bf7
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/phy/allwinner,suniv-
> > f1c100s-usb-phy.yaml
> > @@ -0,0 +1,83 @@
> > +# SPDX-License-Identifier: GPL-2.0
> 
> Dual license please.

I am based on another Allwinner USB PHY binding file in the same
directory, and that file is single licensed. I created a new file
because each variant of the PHY has a single file now.

> 
> > +%YAML 1.2
> > +---
> > +$id:
> > http://devicetree.org/schemas/phy/allwinner,suniv-f1c100s-usb-phy.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Allwinner F1C100s USB PHY Device Tree Bindings
> > +
> > +maintainers:
> > +  - Chen-Yu Tsai <wens at csie.org>
> > +  - Maxime Ripard <mripard at kernel.org>
> > +
> > +properties:
> > +  "#phy-cells":
> > +    const: 1
> > +
> > +  compatible:
> > +    const: allwinner,suniv-f1c100s-usb-phy
> > +
> > +  reg:
> > +    maxItems: 1
> > +    description: PHY Control registers
> > +
> > +  reg-names:
> > +    const: phy_ctrl
> > +
> > +  clocks:
> > +    maxItems: 1
> > +    description: USB OTG PHY bus clock
> > +
> > +  clock-names:
> > +    const: usb0_phy
> 
> *-names is not needed with only one entry. Plus, just using the
> module 
> name is not a great choice.

However the driver expects it...

Should I patch the driver to use no name on F1C100s?

> 
> > +
> > +  resets:
> > +    maxItems: 1
> > +    description: USB OTG reset
> > +
> > +  reset-names:
> > +    const: usb0_reset
> 
> Same here.
> 
> > +  usb0_id_det-gpios:
> > +    maxItems: 1
> > +    description: GPIO to the USB OTG ID pin
> > +
> > +  usb0_vbus_det-gpios:
> > +    maxItems: 1
> > +    description: GPIO to the USB OTG VBUS detect pin
> > +
> > +  usb0_vbus_power-supply:
> > +    description: Power supply to detect the USB OTG VBUS
> > +
> > +  usb0_vbus-supply:
> > +    description: Regulator controlling USB OTG VBUS
> 
> Why the 'usb0_' prefix?
> 
> Are these GPIOs and Vbus supply connected to the phy? If not, these
> all 
> belong in a connector node (as that is where they are connected to in
> h/w).

Well these are historical things of phy-sun4i-usb driver too.

> 
> > +
> > +required:
> > +  - "#phy-cells"
> > +  - compatible
> > +  - clocks
> > +  - clock-names
> > +  - reg
> > +  - reg-names
> > +  - resets
> > +  - reset-names
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > +  - |
> > +    #include <dt-bindings/gpio/gpio.h>
> > +    #include <dt-bindings/clock/suniv-f1c100s-ccu.h>
> > +    #include <dt-bindings/reset/suniv-f1c100s-ccu.h>
> > +
> > +    phy at 1c13400 {
> > +        compatible = "allwinner,suniv-f1c100s-usb-phy";
> > +        reg = <0x01c13400 0x10>;
> > +        reg-names = "phy_ctrl";
> > +        clocks = <&ccu CLK_USB_PHY0>;
> > +        clock-names = "usb0_phy";
> > +        resets = <&ccu RST_USB_PHY0>;
> > +        reset-names = "usb0_reset";
> > +        #phy-cells = <1>;
> > +        usb0_id_det-gpios = <&pio 4 2 GPIO_ACTIVE_HIGH>;
> > +    };
> > -- 
> > 2.36.0
> > 
> > 





More information about the linux-arm-kernel mailing list