[PATCH 2/2] arm64: dts: rockchip: rock-pi-s add more peripherals

[Heiko Stübner]

Am Mittwoch, 8. Juni 2022, 14:07:33 CEST schrieb Sjoerd Simons:
> Hey Michael,
> 
> On Mon, 2022-06-06 at 14:00 +0200, Michael Riesch wrote:
> > 
> > > +       aliases {
> > > +               ethernet0 = &gmac;
> > > +               mmc0 = &emmc;
> > > +               mmc1 = &sdmmc;
> > 
> > Sure? emmc is at address ff49000 which is larger than sdmmc's address
> > ff480000. I believe the aliases should be sorted w.r.t. addresses.
> 
> Do you have a reference about this sorting requirement? 

I do believe we used that mmcx -> *mmc-device sorted by address
when the aliases still were in the main soc dtsi. Simply because one
couldn't really know what was available on a specific board
(no emmc for example).

I guess now on a per-board level we could actually do that more relaxed
and let that be the decision of the board submitter ;-) .

Heiko

> Also do you mean that mmc0 should be &sdmmc *or* that the aliases
> should have mmc1 listed first.
> 
> For reference the reason is that mmc0 is emmc is because it seems more
> logical to have the builtin devices come first (e.g. as mmcblk0) 
> 
> 
> > Best regards,
> > Michael
> > 
> > > +       };
> > > +
> > >         chosen {
> > >                 stdout-path = "serial0:1500000n8";
> > >         };
> > > @@ -132,6 +138,15 @@ &emmc {
> > >         status = "okay";
> > >  };
> > >  
> > > +&gmac {
> > > +       clock_in_out = "output";
> > > +       phy-supply = <&vcc_io>;
> > > +       snps,reset-gpio = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
> > > +       snps,reset-active-low;
> > > +       snps,reset-delays-us = <0 50000 50000>;
> > > +       status = "okay";
> > > +};
> > > +
> > >  &i2c1 {
> > >         status = "okay";
> > >  };
> > > @@ -195,10 +210,47 @@ &sdmmc {
> > >         status = "okay";
> > >  };
> > >  
> > > +&u2phy {
> > > +       status = "okay";
> > > +
> > > +       u2phy_host: host-port {
> > > +               phy-supply = <&vcc5v0_otg>;
> > > +               status = "okay";
> > > +       };
> > > +
> > > +       u2phy_otg: otg-port {
> > > +               phy-supply = <&vcc5v0_otg>;
> > > +               status = "okay";
> > > +       };
> > > +};
> > > +
> > >  &uart0 {
> > >         status = "okay";
> > >  };
> > >  
> > >  &uart4 {
> > >         status = "okay";
> > > +
> > > +       bluetooth {
> > > +               compatible = "realtek,rtl8723bs-bt";
> > > +               device-wake-gpios = <&gpio4 RK_PB3
> > > GPIO_ACTIVE_HIGH>;
> > > +               host-wake-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>;
> > > +       };
> > > +};
> > > +
> > > +&usb_host_ehci {
> > > +       status = "okay";
> > > +};
> > > +
> > > +&usb_host_ohci {
> > > +       status = "okay";
> > > +};
> > > +
> > > +&usb20_otg {
> > > +       dr_mode = "peripheral";
> > > +       status = "okay";
> > > +};
> > > +
> > > +&wdt {
> > > +       status = "okay";
> > >  };
> 
>