[PATCH v6 0/3] PCI: IPQ6018 platform support

[Robert Marko]

On Wed, May 11, 2022 at 4:03 PM Lorenzo Pieralisi
<lorenzo.pieralisi at arm.com> wrote:
>
> On Tue, Apr 12, 2022 at 05:12:59PM +0100, Lorenzo Pieralisi wrote:
> > On Mon, Feb 07, 2022 at 04:51:23PM +0200, Baruch Siach wrote:
> > > This series adds support for the single PCIe lane on IPQ6018 SoCs. The code is
> > > ported from downstream Codeaurora v5.4 kernel. The main difference from
> > > downstream code is the split of PCIe registers configuration from .init to
> > > .post_init, since it requires phy_power_on().
> > >
> > > Tested on IPQ6010 based hardware.
> > >
> > > Changes in v6:
> > >
> > >   * Drop DT patch applied to the qcom tree
> > >
> > >   * Normalize driver changes subject line
> > >
> > >   * Add a preparatory patch to rename PCIE_CAP_LINK1_VAL to PCIE_CAP_SLOT_VAL,
> > >     and define it using PCI_EXP_SLTCAP_* macros
> > >
> > >   * Drop a vague comment about ASPM configuration
> > >
> > >   * Add a comment about the source of delay periods
> > >
> > > Changes in v5:
> > >
> > >   * Remove comments from qcom_pcie_init_2_9_0() (Bjorn Andersson)
> > >
> > > Changes in v4:
> > >
> > >   * Drop applied DT bits
> > >
> > >   * Add max-link-speed that was missing from the applied v2 patch
> > >
> > >   * Rebase the driver on v5.16-rc3
> > >
> > > Changes in v3:
> > >
> > >   * Drop applied patches
> > >
> > >   * Rely on generic code for speed setup
> > >
> > >   * Drop unused macros
> > >
> > >   * Formatting fixes
> > >
> > > Changes in v2:
> > >
> > >   * Add patch moving GEN3_RELATED macros to a common header
> > >
> > >   * Drop ATU configuration from pcie-qcom
> > >
> > >   * Remove local definition of common registers
> > >
> > >   * Use bulk clk and reset APIs
> > >
> > >   * Remove msi-parent from device-tree
> > >
> > > Baruch Siach (2):
> > >   PCI: dwc: tegra: move GEN3_RELATED DBI register to common header
> > >   PCI: qcom: Define slot capabilities using PCI_EXP_SLTCAP_*
> > >
> > > Selvam Sathappan Periakaruppan (1):
> > >   PCI: qcom: Add IPQ60xx support
> > >
> > >  drivers/pci/controller/dwc/pcie-designware.h |   7 +
> > >  drivers/pci/controller/dwc/pcie-qcom.c       | 155 ++++++++++++++++++-
> > >  drivers/pci/controller/dwc/pcie-tegra194.c   |   6 -
> > >  3 files changed, 160 insertions(+), 8 deletions(-)
> >
> > Hi Bjorn, Andy,
> >
> > any feedback on this series please ?
>
> Any feedback on these patches please ?

Finally dug the CP01, and for me, it works, so:
Tested-by: Robert Marko <robert.marko at sartura.hr>

Can we finally get this merged or at least looked at.
IPQ8074 will also benefit from this.

Regards,
Robert
>
> Thanks,
> Lorenzo



-- 
Robert Marko
Staff Embedded Linux Engineer
Sartura Ltd.
Lendavska ulica 16a
10000 Zagreb, Croatia
Email: robert.marko at sartura.hr
Web: www.sartura.hr