[PATCH 5/6] ufs: host: ufs-exynos: add support for fsd ufs hci

Alim Akhtar alim.akhtar at samsung.com
Thu Jun 2 18:42:20 PDT 2022


Hi Chanho
Thanks for the review.

>-----Original Message-----
>From: Chanho Park [mailto:chanho61.park at samsung.com]
>Sent: Tuesday, May 31, 2022 1:07 PM
>To: 'Alim Akhtar' <alim.akhtar at samsung.com>; linux-arm-
>kernel at lists.infradead.org; linux-kernel at vger.kernel.org; linux-
>scsi at vger.kernel.org; linux-phy at lists.infradead.org
>Cc: devicetree at vger.kernel.org; robh+dt at kernel.org;
>krzysztof.kozlowski+dt at linaro.org; vkoul at kernel.org; avri.altman at wdc.com;
>bvanassche at acm.org; martin.petersen at oracle.com;
>pankaj.dubey at samsung.com; linux-fsd at tesla.com; 'Bharat Uppal'
><bharat.uppal at samsung.com>
>Subject: RE: [PATCH 5/6] ufs: host: ufs-exynos: add support for fsd ufs hci
>
>Hi,
>
>> -----Original Message-----
>> From: Alim Akhtar <alim.akhtar at samsung.com>
>> Sent: Tuesday, May 31, 2022 10:22 AM
>> To: linux-arm-kernel at lists.infradead.org;
>> linux-kernel at vger.kernel.org; linux-scsi at vger.kernel.org;
>> linux-phy at lists.infradead.org
>> Cc: devicetree at vger.kernel.org; robh+dt at kernel.org;
>> krzysztof.kozlowski+dt at linaro.org; vkoul at kernel.org;
>> avri.altman at wdc.com; bvanassche at acm.org;
>martin.petersen at oracle.com;
>> chanho61.park at samsung.com; pankaj.dubey at samsung.com; Alim Akhtar
>> <alim.akhtar at samsung.com>; linux- fsd at tesla.com; Bharat Uppal
>> <bharat.uppal at samsung.com>
>> Subject: [PATCH 5/6] ufs: host: ufs-exynos: add support for fsd ufs
>> hci
>>
>> Adds support of UFS HCI which is found in Tesla FSD SoC. FSD also have
>> an addition bit for MPHY APB clock which was not there (was reserved)
>> for previous exynos SoC.
>>
>> Cc: linux-fsd at tesla.com
>> Signed-off-by: Bharat Uppal <bharat.uppal at samsung.com>
>> Signed-off-by: Alim Akhtar <alim.akhtar at samsung.com>
>> ---
>>  drivers/ufs/host/ufs-exynos.c | 143
>> +++++++++++++++++++++++++++++++++-
>>  1 file changed, 142 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/ufs/host/ufs-exynos.c
>> b/drivers/ufs/host/ufs-exynos.c index a81d8cbd542f..b3efdc4caca2
>> 100644
>> --- a/drivers/ufs/host/ufs-exynos.c
>> +++ b/drivers/ufs/host/ufs-exynos.c
>> @@ -52,11 +52,12 @@
>>  #define HCI_ERR_EN_DME_LAYER	0x88
>>  #define HCI_CLKSTOP_CTRL	0xB0
>>  #define REFCLKOUT_STOP		BIT(4)
>> +#define MPHY_APBCLK_STOP        BIT(3)
>>  #define REFCLK_STOP		BIT(2)
>>  #define UNIPRO_MCLK_STOP	BIT(1)
>>  #define UNIPRO_PCLK_STOP	BIT(0)
>>  #define CLK_STOP_MASK		(REFCLKOUT_STOP | REFCLK_STOP |\
>> -				 UNIPRO_MCLK_STOP |\
>> +				 UNIPRO_MCLK_STOP |
>MPHY_APBCLK_STOP|\
>
>Please make this change into a separate patch of this series.
>
Sure, will separate it out.

>>  				 UNIPRO_PCLK_STOP)
>>  #define HCI_MISC		0xB4
>>  #define REFCLK_CTRL_EN		BIT(7)
>> @@ -386,6 +387,104 @@ static int exynos7_ufs_post_pwr_change(struct
>> exynos_ufs *ufs,
>>  	return 0;
>>  }
>>
>> +static inline int fsd_ufs_pre_link(struct exynos_ufs *ufs) {
>> +	int i;
>> +	struct ufs_hba *hba = ufs->hba;
>> +
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x9514), 1000000000L / ufs-
>> >mclk_rate);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x201), 0x12);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x200), 0x40);
>> +
>> +	for_each_ufs_tx_lane(ufs, i) {
>> +		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0xAA, i),
>1000000000L /
>> ufs->mclk_rate);
>> +		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x8F, i), 0x3F);
>> +	}
>> +
>> +	for_each_ufs_rx_lane(ufs, i) {
>> +		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x12, i),
>1000000000L /
>> ufs->mclk_rate);
>> +		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x5C, i), 0x38);
>> +		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x0F, i), 0x0);
>> +		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x65, i), 0x1);
>> +		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x69, i), 0x1);
>> +		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x21, i), 0x0);
>> +		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x22, i), 0x0);
>> +	}
>> +
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x200), 0x0);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x9536), 0x4E20);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x9564), 0x2e820183);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x155E), 0x0);
>
>Use PA_LOCAL_TX_LCC_ENABLE instead of 0x155E. I think you can find more
>values from unipro.h.
>Please try to use as much as possible :)
>
Noted

>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x3000), 0x0);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x3001), 0x1);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x4021), 0x1);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x4020), 0x1);
>
>They can be set from exynos_ufs_establish_connt.
>
Ok, 

>> +
>> +	return 0;
>> +}
>> +
>> +static inline int fsd_ufs_post_link(struct exynos_ufs *ufs) {
>> +	int i;
>> +	struct ufs_hba *hba = ufs->hba;
>> +	u32 hw_cap_min_tactivate;
>> +	u32 peer_rx_min_actv_time_cap;
>> +	u32 max_rx_hibern8_time_cap;
>> +
>> +	ufshcd_dme_get(hba, UIC_ARG_MIB_SEL(0x8F, 4),
>> +			&hw_cap_min_tactivate); /* HW Capability of
>> MIN_TACTIVATE */
>> +	ufshcd_dme_get(hba, UIC_ARG_MIB(0x15A8),
>> +			&peer_rx_min_actv_time_cap);    /* PA_TActivate */
>> +	ufshcd_dme_get(hba, UIC_ARG_MIB(0x15A7),
>> +			&max_rx_hibern8_time_cap);      /* PA_Hibern8Time
>*/
>> +
>> +	if (peer_rx_min_actv_time_cap >= hw_cap_min_tactivate)
>> +		ufshcd_dme_peer_set(hba, UIC_ARG_MIB(0x15A8),
>> +					peer_rx_min_actv_time_cap + 1);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x15A7),
>max_rx_hibern8_time_cap +
>> 1);
>> +
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x9529), 0x01);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x15A4), 0xFA);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x9529), 0x00);
>> +
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x200), 0x40);
>> +
>> +	for_each_ufs_rx_lane(ufs, i) {
>> +		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x35, i), 0x05);
>> +		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x73, i), 0x01);
>> +		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x41, i), 0x02);
>> +		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x42, i), 0xAC);
>> +	}
>> +
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x200), 0x0);
>> +
>> +	return 0;
>> +}
>> +
>> +static inline int fsd_ufs_pre_pwr_change(struct exynos_ufs *ufs,
>> +					struct ufs_pa_layer_attr *pwr)
>> +{
>> +	struct ufs_hba *hba = ufs->hba;
>> +
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x1569), 0x1);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x1584), 0x1);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x2041), 8064);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x2042), 28224);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x2043), 20160);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x15B0), 12000);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x15B1), 32000);
>> +	ufshcd_dme_set(hba, UIC_ARG_MIB(0x15B2), 16000);
>> +
>> +	unipro_writel(ufs, 8064, 0x7888);
>> +	unipro_writel(ufs, 28224, 0x788C);
>> +	unipro_writel(ufs, 20160, 0x7890);
>> +	unipro_writel(ufs, 12000, 0x78B8);
>> +	unipro_writel(ufs, 32000, 0x78BC);
>> +	unipro_writel(ufs, 16000, 0x78C0);
>> +
>> +	return 0;
>> +}
>> +
>>  /*
>>   * exynos_ufs_auto_ctrl_hcc - HCI core clock control by h/w
>>   * Control should be disabled in the below cases @@ -1595,6 +1694,46
>> @@ static struct exynos_ufs_drv_data exynos_ufs_drvs = {
>>  	.post_pwr_change	= exynos7_ufs_post_pwr_change,
>>  };
>>
>> +static struct exynos_ufs_uic_attr fsd_uic_attr = {
>> +	.tx_trailingclks		= 0x10,
>> +	.tx_dif_p_nsec			= 3000000,	/* unit: ns */
>> +	.tx_dif_n_nsec			= 1000000,	/* unit: ns */
>> +	.tx_high_z_cnt_nsec		= 20000,	/* unit: ns */
>> +	.tx_base_unit_nsec		= 100000,	/* unit: ns */
>> +	.tx_gran_unit_nsec		= 4000,		/* unit: ns */
>> +	.tx_sleep_cnt			= 1000,		/* unit: ns */
>> +	.tx_min_activatetime		= 0xa,
>> +	.rx_filler_enable		= 0x2,
>> +	.rx_dif_p_nsec			= 1000000,	/* unit: ns */
>> +	.rx_hibern8_wait_nsec		= 4000000,	/* unit: ns */
>> +	.rx_base_unit_nsec		= 100000,	/* unit: ns */
>> +	.rx_gran_unit_nsec		= 4000,		/* unit: ns */
>> +	.rx_sleep_cnt			= 1280,		/* unit: ns */
>> +	.rx_stall_cnt			= 320,		/* unit: ns */
>> +	.rx_hs_g1_sync_len_cap		= SYNC_LEN_COARSE(0xf),
>> +	.rx_hs_g2_sync_len_cap		= SYNC_LEN_COARSE(0xf),
>> +	.rx_hs_g3_sync_len_cap		= SYNC_LEN_COARSE(0xf),
>> +	.rx_hs_g1_prep_sync_len_cap	= PREP_LEN(0xf),
>> +	.rx_hs_g2_prep_sync_len_cap	= PREP_LEN(0xf),
>> +	.rx_hs_g3_prep_sync_len_cap	= PREP_LEN(0xf),
>> +	.pa_dbg_option_suite		= 0x2E820183,
>> +};
>> +
>> +struct exynos_ufs_drv_data fsd_ufs_drvs = {
>> +	.uic_attr               = &fsd_uic_attr,
>> +	.quirks                 = UFSHCD_QUIRK_PRDT_BYTE_GRAN |
>> +				  UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR |
>> +
>UFSHCD_QUIRK_BROKEN_OCS_FATAL_ERROR |
>> +				  UFSHCI_QUIRK_SKIP_RESET_INTR_AGGR,
>> +	.opts                   = EXYNOS_UFS_OPT_HAS_APB_CLK_CTRL |
>> +
>EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL |
>> +				  EXYNOS_UFS_OPT_SKIP_CONFIG_PHY_ATTR
>|
>> +				  EXYNOS_UFS_OPT_BROKEN_RX_SEL_IDX,
>> +	.pre_link               = fsd_ufs_pre_link,
>> +	.post_link              = fsd_ufs_post_link,
>> +	.pre_pwr_change         = fsd_ufs_pre_pwr_change,
>> +};
>> +
>>  static const struct of_device_id exynos_ufs_of_match[] = {
>>  	{ .compatible = "samsung,exynos7-ufs",
>>  	  .data	      = &exynos_ufs_drvs },
>> @@ -1602,6 +1741,8 @@ static const struct of_device_id
>> exynos_ufs_of_match[] = {
>>  	  .data	      = &exynosauto_ufs_drvs },
>>  	{ .compatible = "samsung,exynosautov9-ufs-vh",
>>  	  .data	      = &exynosauto_ufs_vh_drvs },
>> +	{ .compatible = "tesla,fsd-ufs",
>> +	  .data       = &fsd_ufs_drvs },
>>  	{},
>>  };
>>
>> --
>> 2.25.1
>





More information about the linux-arm-kernel mailing list