[PATCH v14 13/17] PCI: imx6: Reduce resume time by only starting link if it was up before suspend

[Hongxing Zhu]

> -----Original Message-----
> From: Lucas Stach <l.stach at pengutronix.de>
> Sent: 2022年7月13日 16:48
> To: Hongxing Zhu <hongxing.zhu at nxp.com>; bhelgaas at google.com;
> robh+dt at kernel.org; broonie at kernel.org; lorenzo.pieralisi at arm.com;
> festevam at gmail.com; francesco.dolcini at toradex.com
> Cc: linux-pci at vger.kernel.org; linux-arm-kernel at lists.infradead.org;
> linux-kernel at vger.kernel.org; kernel at pengutronix.de; dl-linux-imx
> <linux-imx at nxp.com>
> Subject: Re: [PATCH v14 13/17] PCI: imx6: Reduce resume time by only starting
> link if it was up before suspend
> 
> Am Freitag, dem 01.07.2022 um 11:25 +0800 schrieb Richard Zhu:
> > Because i.MX PCIe doesn't support hot-plug feature.  In the link down
> > scenario, only start the PCIe link training in resume when the link is
> > up before system suspend to avoid the long latency in the link
> > training period.
> >
> > Signed-off-by: Richard Zhu <hongxing.zhu at nxp.com>
> > Signed-off-by: Bjorn Helgaas <bhelgaas at google.com>
> > ---
> >  drivers/pci/controller/dwc/pci-imx6.c | 8 +++++---
> >  1 file changed, 5 insertions(+), 3 deletions(-)
> >
> > diff --git a/drivers/pci/controller/dwc/pci-imx6.c
> > b/drivers/pci/controller/dwc/pci-imx6.c
> > index e236f824c808..5a06fbca82d6 100644
> > --- a/drivers/pci/controller/dwc/pci-imx6.c
> > +++ b/drivers/pci/controller/dwc/pci-imx6.c
> > @@ -67,6 +67,7 @@ struct imx6_pcie {
> >  	struct dw_pcie		*pci;
> >  	int			reset_gpio;
> >  	bool			gpio_active_high;
> > +	bool			link_is_up;
> >  	struct clk		*pcie_bus;
> >  	struct clk		*pcie_phy;
> >  	struct clk		*pcie_inbound_axi;
> > @@ -881,11 +882,13 @@ static int imx6_pcie_start_link(struct dw_pcie
> *pci)
> >  		dev_info(dev, "Link: Gen2 disabled\n");
> >  	}
> >
> > +	imx6_pcie->link_is_up = true;
> >  	tmp = dw_pcie_readw_dbi(pci, offset + PCI_EXP_LNKSTA);
> >  	dev_info(dev, "Link up, Gen%i\n", tmp & PCI_EXP_LNKSTA_CLS);
> >  	return 0;
> >
> >  err_reset_phy:
> > +	imx6_pcie->link_is_up = false;
> >  	dev_dbg(dev, "PHY DEBUG_R0=0x%08x DEBUG_R1=0x%08x\n",
> >  		dw_pcie_readl_dbi(pci, PCIE_PORT_DEBUG0),
> >  		dw_pcie_readl_dbi(pci, PCIE_PORT_DEBUG1)); @@ -1032,9 +1035,8
> @@
> > static int imx6_pcie_resume_noirq(struct device *dev)
> >  		return ret;
> >  	dw_pcie_setup_rc(pp);
> >
> > -	ret = imx6_pcie_start_link(imx6_pcie->pci);
> > -	if (ret < 0)
> > -		dev_info(dev, "pcie link is down after resume.\n");
> > +	if (imx6_pcie->link_is_up)
> > +		imx6_pcie_start_link(imx6_pcie->pci);
> 
> While the change itself is correct, the removal of the return value check should
> be added to the previous patch, as that's the point where you change this
> function to always return 0, rendering this check pointless.
Thanks for your comments.
Yes, it is. Indeed the return check should be cleaned up in the 12/17, since
 imx6_pcie_start_link() always returns 0.

Best Regards
Richard Zhu

> 
> Regards,
> Lucas
> 
> >
> >  	return 0;
> >  }
>