[PATCH 1/2] serial: Embed rs485_supported to uart_port
Lino Sanfilippo
LinoSanfilippo at gmx.de
Tue Jul 5 03:41:11 PDT 2022
On 04.07.22 11:45, Ilpo Järvinen wrote:
> Embed rs485_supported to uart_port to allow serial core to tweak it as
> needed.
>
> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen at linux.intel.com>
> ---
> drivers/tty/serial/8250/8250_bcm2835aux.c | 2 +-
> drivers/tty/serial/8250/8250_dwlib.c | 4 ++--
> drivers/tty/serial/8250/8250_exar.c | 2 +-
> drivers/tty/serial/8250/8250_fintek.c | 4 ++--
> drivers/tty/serial/8250/8250_lpc18xx.c | 2 +-
> drivers/tty/serial/8250/8250_of.c | 2 +-
> drivers/tty/serial/8250/8250_pci.c | 2 +-
> drivers/tty/serial/amba-pl011.c | 2 +-
> drivers/tty/serial/ar933x_uart.c | 4 ++--
> drivers/tty/serial/atmel_serial.c | 2 +-
> drivers/tty/serial/fsl_lpuart.c | 2 +-
> drivers/tty/serial/imx.c | 4 ++--
> drivers/tty/serial/max310x.c | 2 +-
> drivers/tty/serial/mcf.c | 4 ++--
> drivers/tty/serial/omap-serial.c | 2 +-
> drivers/tty/serial/sc16is7xx.c | 2 +-
> drivers/tty/serial/serial_core.c | 8 ++++----
> drivers/tty/serial/stm32-usart.c | 2 +-
> include/linux/serial_core.h | 2 +-
> 19 files changed, 27 insertions(+), 27 deletions(-)
>
> diff --git a/drivers/tty/serial/8250/8250_bcm2835aux.c b/drivers/tty/serial/8250/8250_bcm2835aux.c
> index d9f1e618cfbd..047e14ccb165 100644
> --- a/drivers/tty/serial/8250/8250_bcm2835aux.c
> +++ b/drivers/tty/serial/8250/8250_bcm2835aux.c
> @@ -108,7 +108,7 @@ static int bcm2835aux_serial_probe(struct platform_device *pdev)
> up.port.flags = UPF_SHARE_IRQ | UPF_FIXED_PORT | UPF_FIXED_TYPE |
> UPF_SKIP_TEST | UPF_IOREMAP;
> up.port.rs485_config = serial8250_em485_config;
> - up.port.rs485_supported = &serial8250_em485_supported;
> + up.port.rs485_supported = serial8250_em485_supported;
> up.rs485_start_tx = bcm2835aux_rs485_start_tx;
> up.rs485_stop_tx = bcm2835aux_rs485_stop_tx;
>
> diff --git a/drivers/tty/serial/8250/8250_dwlib.c b/drivers/tty/serial/8250/8250_dwlib.c
> index a8bbed74ea70..2c3b1468bd88 100644
> --- a/drivers/tty/serial/8250/8250_dwlib.c
> +++ b/drivers/tty/serial/8250/8250_dwlib.c
> @@ -255,10 +255,10 @@ void dw8250_setup_port(struct uart_port *p)
> if (pd->hw_rs485_support) {
> p->rs485_config = dw8250_rs485_config;
> up->lsr_save_mask = LSR_SAVE_FLAGS | DW_UART_LSR_ADDR_RCVD;
> - p->rs485_supported = &dw8250_rs485_supported;
> + p->rs485_supported = dw8250_rs485_supported;
> } else {
> p->rs485_config = serial8250_em485_config;
> - p->rs485_supported = &serial8250_em485_supported;
> + p->rs485_supported = serial8250_em485_supported;
> up->rs485_start_tx = serial8250_em485_start_tx;
> up->rs485_stop_tx = serial8250_em485_stop_tx;
> }
> diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
> index f5344cfe303c..314a05e009df 100644
> --- a/drivers/tty/serial/8250/8250_exar.c
> +++ b/drivers/tty/serial/8250/8250_exar.c
> @@ -550,7 +550,7 @@ pci_xr17v35x_setup(struct exar8250 *priv, struct pci_dev *pcidev,
>
> port->port.uartclk = baud * 16;
> port->port.rs485_config = platform->rs485_config;
> - port->port.rs485_supported = platform->rs485_supported;
> + port->port.rs485_supported = *(platform->rs485_supported);
>
> /*
> * Setup the UART clock for the devices on expansion slot to
> diff --git a/drivers/tty/serial/8250/8250_fintek.c b/drivers/tty/serial/8250/8250_fintek.c
> index eea693f5b577..65b6b3cbaff6 100644
> --- a/drivers/tty/serial/8250/8250_fintek.c
> +++ b/drivers/tty/serial/8250/8250_fintek.c
> @@ -433,9 +433,9 @@ static void fintek_8250_set_rs485_handler(struct uart_8250_port *uart)
> case CHIP_ID_F81865:
> uart->port.rs485_config = fintek_8250_rs485_config;
> if (!pdata->index)
> - uart->port.rs485_supported = &fintek_8250_rs485_supported_port0;
> + uart->port.rs485_supported = fintek_8250_rs485_supported_port0;
> else
> - uart->port.rs485_supported = &fintek_8250_rs485_supported;
> + uart->port.rs485_supported = fintek_8250_rs485_supported;
> break;
>
> default: /* No RS485 Auto direction functional */
> diff --git a/drivers/tty/serial/8250/8250_lpc18xx.c b/drivers/tty/serial/8250/8250_lpc18xx.c
> index d7cb3bb52069..d6ca0d47e9d5 100644
> --- a/drivers/tty/serial/8250/8250_lpc18xx.c
> +++ b/drivers/tty/serial/8250/8250_lpc18xx.c
> @@ -161,7 +161,7 @@ static int lpc18xx_serial_probe(struct platform_device *pdev)
> uart.port.uartclk = clk_get_rate(data->clk_uart);
> uart.port.private_data = data;
> uart.port.rs485_config = lpc18xx_rs485_config;
> - uart.port.rs485_supported = &lpc18xx_rs485_supported;
> + uart.port.rs485_supported = lpc18xx_rs485_supported;
> uart.port.serial_out = lpc18xx_uart_serial_out;
>
> uart.dma = &data->dma;
> diff --git a/drivers/tty/serial/8250/8250_of.c b/drivers/tty/serial/8250/8250_of.c
> index 65cccd559db2..1b461fba15a3 100644
> --- a/drivers/tty/serial/8250/8250_of.c
> +++ b/drivers/tty/serial/8250/8250_of.c
> @@ -165,7 +165,7 @@ static int of_platform_serial_setup(struct platform_device *ofdev,
>
> port->dev = &ofdev->dev;
> port->rs485_config = serial8250_em485_config;
> - port->rs485_supported = &serial8250_em485_supported;
> + port->rs485_supported = serial8250_em485_supported;
> up->rs485_start_tx = serial8250_em485_start_tx;
> up->rs485_stop_tx = serial8250_em485_stop_tx;
>
> diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
> index d31d2350a9db..8a39ae072c65 100644
> --- a/drivers/tty/serial/8250/8250_pci.c
> +++ b/drivers/tty/serial/8250/8250_pci.c
> @@ -1607,7 +1607,7 @@ static int pci_fintek_setup(struct serial_private *priv,
> port->port.iotype = UPIO_PORT;
> port->port.iobase = iobase;
> port->port.rs485_config = pci_fintek_rs485_config;
> - port->port.rs485_supported = &pci_fintek_rs485_supported;
> + port->port.rs485_supported = pci_fintek_rs485_supported;
>
> data = devm_kzalloc(&pdev->dev, sizeof(u8), GFP_KERNEL);
> if (!data)
> diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
> index c8f52945a4aa..abeceeefdece 100644
> --- a/drivers/tty/serial/amba-pl011.c
> +++ b/drivers/tty/serial/amba-pl011.c
> @@ -2779,7 +2779,7 @@ static int pl011_probe(struct amba_device *dev, const struct amba_id *id)
> uap->port.irq = dev->irq[0];
> uap->port.ops = &amba_pl011_pops;
> uap->port.rs485_config = pl011_rs485_config;
> - uap->port.rs485_supported = &pl011_rs485_supported;
> + uap->port.rs485_supported = pl011_rs485_supported;
> snprintf(uap->type, sizeof(uap->type), "PL011 rev%u", amba_rev(dev));
>
> ret = pl011_setup_port(&dev->dev, uap, &dev->res, portnr);
> diff --git a/drivers/tty/serial/ar933x_uart.c b/drivers/tty/serial/ar933x_uart.c
> index b73ce13683db..f931ecbc0bc0 100644
> --- a/drivers/tty/serial/ar933x_uart.c
> +++ b/drivers/tty/serial/ar933x_uart.c
> @@ -778,7 +778,7 @@ static int ar933x_uart_probe(struct platform_device *pdev)
> port->fifosize = AR933X_UART_FIFO_SIZE;
> port->ops = &ar933x_uart_ops;
> port->rs485_config = ar933x_config_rs485;
> - port->rs485_supported = &ar933x_rs485_supported;
> + port->rs485_supported = ar933x_rs485_supported;
>
> baud = ar933x_uart_get_baud(port->uartclk, AR933X_UART_MAX_SCALE, 1);
> up->min_baud = max_t(unsigned int, baud, AR933X_UART_MIN_BAUD);
> @@ -802,7 +802,7 @@ static int ar933x_uart_probe(struct platform_device *pdev)
> !up->rts_gpiod) {
> dev_err(&pdev->dev, "lacking rts-gpio, disabling RS485\n");
> port->rs485.flags &= ~SER_RS485_ENABLED;
> - port->rs485_supported = &ar933x_no_rs485;
> + port->rs485_supported = ar933x_no_rs485;
> }
>
> #ifdef CONFIG_SERIAL_AR933X_CONSOLE
> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
> index bc6004679585..30ba9eef7b39 100644
> --- a/drivers/tty/serial/atmel_serial.c
> +++ b/drivers/tty/serial/atmel_serial.c
> @@ -2498,7 +2498,7 @@ static int atmel_init_port(struct atmel_uart_port *atmel_port,
> port->mapbase = mpdev->resource[0].start;
> port->irq = platform_get_irq(mpdev, 0);
> port->rs485_config = atmel_config_rs485;
> - port->rs485_supported = &atmel_rs485_supported;
> + port->rs485_supported = atmel_rs485_supported;
> port->iso7816_config = atmel_config_iso7816;
> port->membase = NULL;
>
> diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
> index 8fe0494d4057..fc7d235a1e27 100644
> --- a/drivers/tty/serial/fsl_lpuart.c
> +++ b/drivers/tty/serial/fsl_lpuart.c
> @@ -2655,7 +2655,7 @@ static int lpuart_probe(struct platform_device *pdev)
> sport->port.rs485_config = lpuart32_config_rs485;
> else
> sport->port.rs485_config = lpuart_config_rs485;
> - sport->port.rs485_supported = &lpuart_rs485_supported;
> + sport->port.rs485_supported = lpuart_rs485_supported;
>
> sport->ipg_clk = devm_clk_get(&pdev->dev, "ipg");
> if (IS_ERR(sport->ipg_clk)) {
> diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
> index 3457006cea3f..522445a8f666 100644
> --- a/drivers/tty/serial/imx.c
> +++ b/drivers/tty/serial/imx.c
> @@ -2285,9 +2285,9 @@ static int imx_uart_probe(struct platform_device *pdev)
> sport->port.rs485_config = imx_uart_rs485_config;
> /* RTS is required to control the RS485 transmitter */
> if (sport->have_rtscts || sport->have_rtsgpio)
> - sport->port.rs485_supported = &imx_rs485_supported;
> + sport->port.rs485_supported = imx_rs485_supported;
> else
> - sport->port.rs485_supported = &imx_no_rs485;
> + sport->port.rs485_supported = imx_no_rs485;
> sport->port.flags = UPF_BOOT_AUTOCONF;
> timer_setup(&sport->timer, imx_uart_timeout, 0);
>
> diff --git a/drivers/tty/serial/max310x.c b/drivers/tty/serial/max310x.c
> index e162bfb44080..ab10ca4a45b5 100644
> --- a/drivers/tty/serial/max310x.c
> +++ b/drivers/tty/serial/max310x.c
> @@ -1370,7 +1370,7 @@ static int max310x_probe(struct device *dev, const struct max310x_devtype *devty
> s->p[i].port.membase = (void __iomem *)~0;
> s->p[i].port.uartclk = uartclk;
> s->p[i].port.rs485_config = max310x_rs485_config;
> - s->p[i].port.rs485_supported = &max310x_rs485_supported;
> + s->p[i].port.rs485_supported = max310x_rs485_supported;
> s->p[i].port.ops = &max310x_ops;
> s->p[i].regmap = regmaps[i];
>
> diff --git a/drivers/tty/serial/mcf.c b/drivers/tty/serial/mcf.c
> index 73c5287b8e5e..f4aaaadd0742 100644
> --- a/drivers/tty/serial/mcf.c
> +++ b/drivers/tty/serial/mcf.c
> @@ -506,7 +506,7 @@ int __init early_mcf_setup(struct mcf_platform_uart *platp)
> port->uartclk = MCF_BUSCLK;
> port->flags = UPF_BOOT_AUTOCONF;
> port->rs485_config = mcf_config_rs485;
> - port->rs485_supported = &mcf_rs485_supported;
> + port->rs485_supported = mcf_rs485_supported;
> port->ops = &mcf_uart_ops;
> }
>
> @@ -634,7 +634,7 @@ static int mcf_probe(struct platform_device *pdev)
> port->ops = &mcf_uart_ops;
> port->flags = UPF_BOOT_AUTOCONF;
> port->rs485_config = mcf_config_rs485;
> - port->rs485_supported = &mcf_rs485_supported;
> + port->rs485_supported = mcf_rs485_supported;
> port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_MCF_CONSOLE);
>
> uart_add_one_port(&mcf_driver, port);
> diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
> index 196bae704f85..0aa666e247d5 100644
> --- a/drivers/tty/serial/omap-serial.c
> +++ b/drivers/tty/serial/omap-serial.c
> @@ -1643,7 +1643,7 @@ static int serial_omap_probe(struct platform_device *pdev)
> up->port.flags = omap_up_info->flags;
> up->port.uartclk = omap_up_info->uartclk;
> up->port.rs485_config = serial_omap_config_rs485;
> - up->port.rs485_supported = &serial_omap_rs485_supported;
> + up->port.rs485_supported = serial_omap_rs485_supported;
> if (!up->port.uartclk) {
> up->port.uartclk = DEFAULT_CLK_SPEED;
> dev_warn(&pdev->dev,
> diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
> index 8cb92a3b3fb8..259e08cc347c 100644
> --- a/drivers/tty/serial/sc16is7xx.c
> +++ b/drivers/tty/serial/sc16is7xx.c
> @@ -1461,7 +1461,7 @@ static int sc16is7xx_probe(struct device *dev,
> s->p[i].port.iotype = UPIO_PORT;
> s->p[i].port.uartclk = freq;
> s->p[i].port.rs485_config = sc16is7xx_config_rs485;
> - s->p[i].port.rs485_supported = &sc16is7xx_rs485_supported;
> + s->p[i].port.rs485_supported = sc16is7xx_rs485_supported;
> s->p[i].port.ops = &sc16is7xx_ops;
> s->p[i].old_mctrl = 0;
> s->p[i].port.line = sc16is7xx_alloc_line();
> diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
> index 85ef7ef00b82..a9cf1044a9fa 100644
> --- a/drivers/tty/serial/serial_core.c
> +++ b/drivers/tty/serial/serial_core.c
> @@ -1285,7 +1285,7 @@ static int uart_check_rs485_flags(struct uart_port *port, struct serial_rs485 *r
> * For any bit outside of the legacy ones that is not supported by
> * the driver, return -EINVAL.
> */
> - if (flags & ~port->rs485_supported->flags)
> + if (flags & ~port->rs485_supported.flags)
> return -EINVAL;
>
> /* Asking for address w/o addressing mode? */
> @@ -1304,7 +1304,7 @@ static int uart_check_rs485_flags(struct uart_port *port, struct serial_rs485 *r
>
> static void uart_sanitize_serial_rs485(struct uart_port *port, struct serial_rs485 *rs485)
> {
> - u32 supported_flags = port->rs485_supported->flags;
> + u32 supported_flags = port->rs485_supported.flags;
>
> if (!(rs485->flags & SER_RS485_ENABLED)) {
> memset(rs485, 0, sizeof(*rs485));
> @@ -1323,7 +1323,7 @@ static void uart_sanitize_serial_rs485(struct uart_port *port, struct serial_rs4
> supported_flags |= SER_RS485_RTS_ON_SEND|SER_RS485_RTS_AFTER_SEND;
> }
>
> - if (!port->rs485_supported->delay_rts_before_send) {
> + if (!port->rs485_supported.delay_rts_before_send) {
> if (rs485->delay_rts_before_send) {
> dev_warn_ratelimited(port->dev,
> "%s (%d): RTS delay before sending not supported\n",
> @@ -1337,7 +1337,7 @@ static void uart_sanitize_serial_rs485(struct uart_port *port, struct serial_rs4
> port->name, port->line, rs485->delay_rts_before_send);
> }
>
> - if (!port->rs485_supported->delay_rts_after_send) {
> + if (!port->rs485_supported.delay_rts_after_send) {
> if (rs485->delay_rts_after_send) {
> dev_warn_ratelimited(port->dev,
> "%s (%d): RTS delay after sending not supported\n",
> diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
> index 13992e64a7df..ff5c7e0ebc4c 100644
> --- a/drivers/tty/serial/stm32-usart.c
> +++ b/drivers/tty/serial/stm32-usart.c
> @@ -1401,7 +1401,7 @@ static int stm32_usart_init_port(struct stm32_port *stm32port,
> port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_STM32_CONSOLE);
> port->irq = irq;
> port->rs485_config = stm32_usart_config_rs485;
> - port->rs485_supported = &stm32_rs485_supported;
> + port->rs485_supported = stm32_rs485_supported;
>
> ret = stm32_usart_init_rs485(port, pdev);
> if (ret)
> diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
> index b7b86ee3cb12..a6fa7c40c330 100644
> --- a/include/linux/serial_core.h
> +++ b/include/linux/serial_core.h
> @@ -255,7 +255,7 @@ struct uart_port {
> struct attribute_group *attr_group; /* port specific attributes */
> const struct attribute_group **tty_groups; /* all attributes (serial core use only) */
> struct serial_rs485 rs485;
> - const struct serial_rs485 *rs485_supported; /* Supported mask for serial_rs485 */
> + struct serial_rs485 rs485_supported; /* Supported mask for serial_rs485 */
> struct gpio_desc *rs485_term_gpio; /* enable RS485 bus termination */
> struct serial_iso7816 iso7816;
> void *private_data; /* generic platform data pointer */
Reviewed-by: Lino Sanfilippo <l.sanfilippo at kunbus.com>
Regards,
Lino
More information about the linux-arm-kernel
mailing list