[PATCH v4 2/2] ARM: dts: bananapi-m2-ultra: Enable USB0_OTG and HOST support

[Samuel Holland]

Hi Qianfan,

On 5/18/22 5:17 AM, qianfanguijin at 163.com wrote:
> From: qianfan Zhao <qianfanguijin at 163.com>
> 
> let USB0 work at OTG mode.
> 
> Signed-off-by: qianfan Zhao <qianfanguijin at 163.com>
> ---
>  .../boot/dts/sun8i-r40-bananapi-m2-ultra.dts  | 39 +++++++++++++++++++
>  1 file changed, 39 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
> index 28197bbcb1d5..b3421e67967d 100644
> --- a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
> +++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
> @@ -122,6 +122,10 @@ &de {
>  	status = "okay";
>  };
>  
> +&ehci0 {
> +	status = "okay";
> +};
> +
>  &ehci1 {
>  	status = "okay";
>  };
> @@ -164,6 +168,7 @@ axp22x: pmic at 34 {
>  		reg = <0x34>;
>  		interrupt-parent = <&nmi_intc>;
>  		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> +		x-powers,drive-vbus-en;
>  	};
>  };
>  
> @@ -199,6 +204,10 @@ &mmc2 {
>  	status = "okay";
>  };
>  
> +&ohci0 {
> +	status = "okay";
> +};
> +
>  &ohci1 {
>  	status = "okay";
>  };
> @@ -216,6 +225,15 @@ &pio {
>  	vcc-pe-supply = <&reg_eldo1>;
>  	vcc-pf-supply = <&reg_dcdc1>;
>  	vcc-pg-supply = <&reg_dldo1>;
> +
> +	/* USB0_DRVVBUS connected to both the PMIC.N_VBUSEN and PI13,
> +	 * we chose PMIC.N_VBUSEN for control, so set the gpio as
> +	 * input mode here.
> +	 */

Toggling a GPIO is going to be more efficient and have lower latency than a PMIC
register write over I2C. (And there are several comments in the USB PHY driver
about latency being important.) So I would prefer to model this as a
GPIO-controlled regulator, and leave N_VBUSEN as an input.

Regards,
Samuel

> +	usb0_vbus_enable_gpio: usb0-vbus-enable-gpio {
> +		pins = "PI13";
> +		function = "gpio_in";
> +	};
>  };
>  
>  &reg_aldo2 {
> @@ -298,6 +316,11 @@ &reg_dldo4 {
>  	regulator-name = "vdd2v5-sata";
>  };
>  
> +&reg_drivevbus {
> +	regulator-name = "usb0-vbus";
> +	status = "okay";
> +};
> +
>  &reg_eldo3 {
>  	regulator-min-microvolt = <1200000>;
>  	regulator-max-microvolt = <1200000>;
> @@ -333,7 +356,23 @@ bluetooth {
>  	};
>  };
>  
> +&usb_otg {
> +	dr_mode = "otg";
> +	status = "okay";
> +};
> +
> +&usb_power_supply {
> +	status = "okay";
> +};
> +
>  &usbphy {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&usb0_vbus_enable_gpio>;
> +
> +	usb0_id_det-gpios = <&pio 8 4 GPIO_ACTIVE_HIGH>; /* PI4 */
> +	usb0_vbus_det-gpios = <&pio 8 8 GPIO_ACTIVE_HIGH>; /* PI8 */
> +	usb0_vbus_power-supply = <&usb_power_supply>;
> +	usb0_vbus-supply = <&reg_drivevbus>;
>  	usb1_vbus-supply = <&reg_vcc5v0>;
>  	usb2_vbus-supply = <&reg_vcc5v0>;
>  	status = "okay";
>