[PATCH v2] rockchip: rk3328: add support for FriendlyARM NanoPi NEO3
Julian Pidancet
julian at pidancet.net
Sun Jan 23 08:19:19 PST 2022
This patch adds support for FriendlyARM NanoPi NEO3
Soc: RockChip RK3328
RAM: 1GB/2GB DDR4
LAN: 10/100/1000M Ethernet with unique MAC
USB Host: 1x USB3.0 Type A and 2x USB2.0 on 2.54mm pin header
MicroSD: x 1 for system boot and storage
LED: Power LED x 1, System LED x 1
Key: User Button x 1
Fan: 2 Pin JST ZH 1.5mm Connector for 5V Fan
GPIO: 26 pin-header, include I2C, UART, SPI, I2S, GPIO
Power: 5V/1A, via Type-C or GPIO
Signed-off-by: Julian Pidancet <julian at pidancet.net>
---
This is another shot at previous work submitted by Marty Jones
<mj8263788 at gmail.com> (https://lore.kernel.org/linux-arm-kernel/20201228152836.02795e09.mj8263788@gmail.com/),
which is now a year old.
v2: Following up on Robin Murphy's comments, the NEO3 DTS is now
standalone and no longer includes the nanopi R2S one. The lan_led and
wan_len nodes have been removed, and the sys_led node has been renamed
to stat_led in accordance with the board schematics.
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3328-nanopi-neo3.dts | 396 ++++++++++++++++++
2 files changed, 397 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-nanopi-neo3.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 479906f3a..5f6ffb496 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -10,6 +10,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3326-odroid-go2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-neo3.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock-pi-e.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-neo3.dts b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-neo3.dts
new file mode 100644
index 000000000..1eb7fd5f7
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-neo3.dts
@@ -0,0 +1,396 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 David Bauer <mail at david-bauer.net>
+ * Copyright (c) 2022 Julian Pidancet <julian at pidancet.net>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "rk3328.dtsi"
+
+/ {
+ model = "FriendlyElec NanoPi NEO3";
+ compatible = "friendlyarm,nanopi-neo3", "rockchip,rk3328";
+
+ aliases {
+ led-boot = &stat_led;
+ led-failsafe = &stat_led;
+ led-running = &stat_led;
+ led-upgrade = &stat_led;
+ };
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ gmac_clk: gmac-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "gmac_clkin";
+ #clock-cells = <0>;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&reset_button_pin>;
+ pinctrl-names = "default";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ debounce-interval = <50>;
+ };
+ };
+
+ vcc_rtl8153: vcc-rtl8153-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rtl8153_en_drv>;
+ regulator-always-on;
+ regulator-name = "vcc_rtl8153";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&stat_led_pin>;
+ pinctrl-names = "default";
+
+ stat_led: led-0 {
+ gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
+ label = "nanopi-neo3:green:stat";
+ };
+ };
+
+ vcc_io_sdio: sdmmcio-regulator {
+ compatible = "regulator-gpio";
+ enable-active-high;
+ gpios = <&gpio1 RK_PD4 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&sdio_vcc_pin>;
+ pinctrl-names = "default";
+ regulator-name = "vcc_io_sdio";
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-settling-time-us = <5000>;
+ regulator-type = "voltage";
+ startup-delay-us = <2000>;
+ states = <1800000 0x1>,
+ <3300000 0x0>;
+ vin-supply = <&vcc_io_33>;
+ };
+
+ vcc_sd: sdmmc-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&sdmmc0m1_pin>;
+ pinctrl-names = "default";
+ regulator-name = "vcc_sd";
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_io_33>;
+ };
+
+ vdd_5v: vdd-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_5v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&display_subsystem {
+ status = "disabled";
+};
+
+&gmac2io {
+ assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
+ assigned-clock-parents = <&gmac_clk>, <&gmac_clk>;
+ clock_in_out = "input";
+ phy-handle = <&rtl8211e>;
+ phy-mode = "rgmii";
+ phy-supply = <&vcc_io_33>;
+ pinctrl-0 = <&rgmiim1_pins>;
+ pinctrl-names = "default";
+ rx_delay = <0x18>;
+ snps,aal;
+ tx_delay = <0x24>;
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rtl8211e: ethernet-phy at 1 {
+ reg = <1>;
+ pinctrl-0 = <ð_phy_reset_pin>;
+ pinctrl-names = "default";
+ reset-assert-us = <10000>;
+ reset-deassert-us = <50000>;
+ reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+
+ rk805: pmic at 18 {
+ compatible = "rockchip,rk805";
+ reg = <0x18>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk805-clkout2";
+ gpio-controller;
+ #gpio-cells = <2>;
+ pinctrl-0 = <&pmic_int_l>;
+ pinctrl-names = "default";
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vdd_5v>;
+ vcc2-supply = <&vdd_5v>;
+ vcc3-supply = <&vdd_5v>;
+ vcc4-supply = <&vdd_5v>;
+ vcc5-supply = <&vcc_io_33>;
+ vcc6-supply = <&vdd_5v>;
+
+ regulators {
+ vdd_log: DCDC_REG1 {
+ regulator-name = "vdd_log";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1450000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vdd_arm: DCDC_REG2 {
+ regulator-name = "vdd_arm";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1450000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <950000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_io_33: DCDC_REG4 {
+ regulator-name = "vcc_io_33";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_18: LDO_REG1 {
+ regulator-name = "vcc_18";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc18_emmc: LDO_REG2 {
+ regulator-name = "vcc18_emmc";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_10: LDO_REG3 {
+ regulator-name = "vdd_10";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+ };
+ };
+
+ usb {
+ rtl8153_en_drv: rtl8153-en-drv {
+ rockchip,pins = <2 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&io_domains {
+ pmuio-supply = <&vcc_io_33>;
+ vccio1-supply = <&vcc_io_33>;
+ vccio2-supply = <&vcc18_emmc>;
+ vccio3-supply = <&vcc_io_sdio>;
+ vccio4-supply = <&vcc_18>;
+ vccio5-supply = <&vcc_io_33>;
+ vccio6-supply = <&vcc_io_33>;
+ status = "okay";
+};
+
+&pinctrl {
+ button {
+ reset_button_pin: reset-button-pin {
+ rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ ethernet-phy {
+ eth_phy_reset_pin: eth-phy-reset-pin {
+ rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ leds {
+ stat_led_pin: stat-led-pin {
+ rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ sd {
+ sdio_vcc_pin: sdio-vcc-pin {
+ rockchip,pins = <1 RK_PD4 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ disable-wp;
+ pinctrl-0 = <&sdmmc0_clk>, <&sdmmc0_cmd>, <&sdmmc0_dectn>, <&sdmmc0_bus4>;
+ pinctrl-names = "default";
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vcc_io_sdio>;
+ status = "okay";
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <0>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+&u2phy {
+ status = "okay";
+};
+
+&u2phy_host {
+ status = "okay";
+};
+
+&u2phy_otg {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb20_otg {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usbdrd3 {
+ status = "okay";
+};
+
+&usbdrd_dwc3 {
+ dr_mode = "host";
+ status = "okay";
+
+ usb-eth at 2 {
+ compatible = "realtek,rtl8153";
+ reg = <2>;
+
+ realtek,led-data = <0x87>;
+ };
+};
--
2.34.1
More information about the linux-arm-kernel
mailing list