[PATCH v5 3/3] ARM: dts: sun8i: r40: add second ethernet support

[Evgeny Boger]

14.01.2022 13:37, Andre Przywara пишет:
> On Fri, 14 Jan 2022 10:42:55 +0100
> Maxime Ripard <maxime at cerno.tech> wrote:
>
> Hi,
>
>> On Thu, Jan 13, 2022 at 08:37:34AM +0300, Evgeny Boger wrote:
>>> R40 (aka V40, A40i, T3) has two different Ethernet IPs
>>> called EMAC and GMAC. EMAC only support 10/100 Mbit in MII mode,
>>> while GMAC support both 10/100 (MII) and 10/100/1000 (RGMII).
>>>
>>> In contrast to A10/A20 where GMAC and EMAC share the same pins
>>> making EMAC somewhat pointless, on R40 EMAC can be routed to port H.
>>> Both EMAC (on port H) and GMAC (on port A) can be then enabled at
>>> the same time, allowing for two ethernet ports.
>>>
>>> Signed-off-by: Evgeny Boger <boger at wirenboard.com>
>>> ---
>>>   arch/arm/boot/dts/sun8i-r40.dtsi | 49 ++++++++++++++++++++++++++++++++
>>>   1 file changed, 49 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi
>>> index 03d3e5f45a09..8770b105f86e 100644
>>> --- a/arch/arm/boot/dts/sun8i-r40.dtsi
>>> +++ b/arch/arm/boot/dts/sun8i-r40.dtsi
>>> @@ -217,6 +217,19 @@ syscon: system-control at 1c00000 {
>>>   			#size-cells = <1>;
>>>   			ranges;
>>>   
>>> +			sram_a: sram at 0 {
>>> +				compatible = "mmio-sram";
>>> +				reg = <0x00000000 0xc000>;
>>> +				#address-cells = <1>;
>>> +				#size-cells = <1>;
>>> +				ranges = <0 0x00000000 0xc000>;
>>> +
>>> +				emac_sram: sram-section at 8000 {
>>> +					compatible = "allwinner,sun4i-a10-sram-a3-a4";
>>> +					reg = <0x8000 0x4000>;
>>> +				};
>>> +			};
>>> +
>>>   			sram_c: sram at 1d00000 {
>>>   				compatible = "mmio-sram";
>>>   				reg = <0x01d00000 0xd0000>;
>>> @@ -553,6 +566,24 @@ gmac_rgmii_pins: gmac-rgmii-pins {
>>>   				drive-strength = <40>;
>>>   			};
>>>   
>>> +			emac_pa_pins: emac-pa-pins {
>>> +				pins = "PA0", "PA1", "PA2",
>>> +				       "PA3", "PA4", "PA5", "PA6",
>>> +				       "PA7", "PA8", "PA9", "PA10",
>>> +				       "PA11", "PA12", "PA13", "PA14",
>>> +				       "PA15", "PA16";
>>> +				function = "emac";
>>> +			};
>>> +
>>> +			emac_ph_pins: emac-ph-pins {
>>> +				pins = "PH8", "PH9", "PH10", "PH11",
>>> +				       "PH14", "PH15", "PH16", "PH17",
>>> +				       "PH18","PH19", "PH20", "PH21",
>>> +				       "PH22", "PH23", "PH24", "PH25",
>>> +				       "PH26", "PH27";
>>> +				function = "emac";
>>> +			};
>> There's 17 pins on the first group, but 18 on the second, is it intentional?
> Yeah, looks like PA17 is missing above. This pin is used for MII only, so
> it is omitted from the existing gmac_rgmii_pins group.
>
> Evgeny: Did you try a 100MBit PHY on PortA? That should work with both the
> GMAC and EMAC, right? I wonder if we should add a group that connects all
> pins needed for MII to the GMAC as well, so basically the above (with PA17
> added), but using 'function = "gmac";'? Put an "/omit-if-no-ref/" before
> that (also to those above?) to avoid blowing up the DTB needlessly.
Hi Andre,

No, it's not intentional, thank you for noticing that!
I haven't tried EMAC on port A with the latest patch, but it should be 
trivial to do.
The problem with TXERR signal is that it's kind of optional, so it's 
hard to notice if it doesn't work properly.

As for adding gmac_*mii*_pins node, I think it could be useful. Do you 
suggest to add it to the same series? Strictly speaking, it has nothing 
to do with R40 and second ethernet support. GMAC is ubiquitous among 
Allwinner SoCs, so I think it would make sense to add to all SoCs at once.

As for /omit-if-no-ref/ on pinctrl nodes, is there a policy on it? I 
mean there are people (ourselves included) who use device tree overlays 
a lot, both in bootloader and kernel, so it's not that harmless.


> Cheers,
> Andre.


-- 
С уважением,
     Евгений Богер / Evgeny Boger
     CTO, Wiren Board Team
     https://wirenboard.com/ru
     +7 495 150 66 19 (# 33)