[PATCH] arm64: dts: imx8mm-venice-gw73xx-0x: add dt overlays for serial modes
Tim Harvey
tharvey at gateworks.com
Mon Jan 10 16:00:21 PST 2022
On Tue, Dec 14, 2021 at 1:36 PM Tim Harvey <tharvey at gateworks.com> wrote:
>
> The imx8mm-venice-gw73xx-0x som+baseboard combination has a multi-protocol
> RS-232/RS-485/RS-422 transceiver to an off-board connector which
> can be configured in a number of ways via UART and GPIO configuration.
>
> The default configuration per the imx8mm-venice-gw73xx-0x dts is for
> UART2 TX/RX and UART4 TX/RX to be available as RS-232:
> J15.1 UART2 TX out
> J15.2 UART2 RX in
> J15.3 UART4 TX out
> J15.4 UART4 RX in
> J15.5 GND
>
> Add dt overlays to allow additional the modes of operation:
>
> rs232-rts (UART2 RS-232 with RTS/CTS hardware flow control)
> J15.1 TX out
> J15.2 RX in
> J15.3 RTS out
> J15.4 CTS in
> J15.5 GND
>
> rs485 (UART2 RS-485 half duplex)
> J15.1 TXRX-
> J15.2 N/C
> J15.3 TXRX+
> J15.4 N/C
> J15.5 GND
>
> rs422 (UART2 RS-422 full duplex)
> J15.1 TX-
> J15.2 RX+
> J15.3 TX+
> J15.4 RX-
> J15.5 GND
>
> Signed-off-by: Tim Harvey <tharvey at gateworks.com>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 3 +
> .../imx8mm-venice-gw73xx-0x-rs232-rts.dts | 53 ++++++++++++++++
> .../imx8mm-venice-gw73xx-0x-rs422.dts | 61 +++++++++++++++++++
> .../imx8mm-venice-gw73xx-0x-rs485.dts | 61 +++++++++++++++++++
> 4 files changed, 178 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs232-rts.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs422.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs485.dts
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index a14a6173b765..5ec8d59347b6 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -44,6 +44,9 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x-rs232-rts.dtbo
> +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x-rs422.dtbo
> +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x-rs485.dtbo
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7901.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7902.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mn-beacon-kit.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs232-rts.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs232-rts.dts
> new file mode 100644
> index 000000000000..c184cf4aea4e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs232-rts.dts
> @@ -0,0 +1,53 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2021 Gateworks Corporation
> + *
> + * GW73xx RS232 with RTS/CTS hardware flow control:
> + * - GPIO4_0 rs485_en needs to be driven low (in-active)
> + * - UART4_TX becomes RTS
> + * - UART4_RX becomes CTS
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +#include "imx8mm-pinfunc.h"
> +
> +/dts-v1/;
> +/plugin/;
> +
> +&{/} {
> + compatible = "gw,imx8mm-gw73xx-0x";
> +};
> +
> +&gpio4 {
> + rs485_en {
> + gpio-hog;
> + gpios = <0 GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "rs485_en";
> + };
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + rts-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
> + cts-gpios = <&gpio5 28 GPIO_ACTIVE_LOW>;
> + uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&uart4 {
> + status = "disabled";
> +};
> +
> +&iomuxc {
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
> + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140
> + MX8MM_IOMUXC_UART4_TXD_GPIO5_IO29 0x140
> + MX8MM_IOMUXC_UART4_RXD_GPIO5_IO28 0x140
> + >;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs422.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs422.dts
> new file mode 100644
> index 000000000000..3e6404340d52
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs422.dts
> @@ -0,0 +1,61 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2021 Gateworks Corporation
> + *
> + * GW73xx RS422 (RS485 full duplex):
> + * - GPIO1_0 rs485_term selects on-chip termination
> + * - GPIO4_0 rs485_en needs to be driven high (active)
> + * - GPIO4_2 rs485_hd needs to be driven low (in-active)
> + * - UART4_TX is DE for RS485 transmitter
> + * - RS485_EN needs to be pulled high
> + * - RS485_HALF needs to be low
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +#include "imx8mm-pinfunc.h"
> +
> +/dts-v1/;
> +/plugin/;
> +
> +&{/} {
> + compatible = "gw,imx8mm-gw73xx-0x";
> +};
> +
> +&gpio4 {
> + rs485_en {
> + gpio-hog;
> + gpios = <0 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "rs485_en";
> + };
> +
> + rs485_hd {
> + gpio-hog;
> + gpios = <2 GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "rs485_hd";
> + };
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + rts-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
> + linux,rs485-enabled-at-boot-time;
> + status = "okay";
> +};
> +
> +&uart4 {
> + status = "disabled";
> +};
> +
> +&iomuxc {
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
> + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140
> + MX8MM_IOMUXC_UART4_TXD_GPIO5_IO29 0x140
> + >;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs485.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs485.dts
> new file mode 100644
> index 000000000000..97f19c15c3d0
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs485.dts
> @@ -0,0 +1,61 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2021 Gateworks Corporation
> + *
> + * GW73xx RS485 HD:
> + * - GPIO1_0 rs485_term selects on-chip termination
> + * - GPIO4_0 rs485_en needs to be driven high (active)
> + * - GPIO4_2 rs485_hd needs to be driven high (active)
> + * - UART4_TX is DE for RS485 transmitter
> + * - RS485_EN needs to be pulled high
> + * - RS485_HALF needs to be pulled high
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +#include "imx8mm-pinfunc.h"
> +
> +/dts-v1/;
> +/plugin/;
> +
> +&{/} {
> + compatible = "gw,imx8mm-gw73xx-0x";
> +};
> +
> +&gpio4 {
> + rs485_en {
> + gpio-hog;
> + gpios = <0 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "rs485_en";
> + };
> +
> + rs485_hd {
> + gpio-hog;
> + gpios = <2 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "rs485_hd";
> + };
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + rts-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
> + linux,rs485-enabled-at-boot-time;
> + status = "okay";
> +};
> +
> +&uart4 {
> + status = "disabled";
> +};
> +
> +&iomuxc {
> + pinctrl_uart2: uast2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
> + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140
> + MX8MM_IOMUXC_UART4_TXD_GPIO5_IO29 0x140
> + >;
> + };
> +};
> --
> 2.17.1
>
gentle ping.
I'm mostly interested to see if my approach to dt fragments here and
the naming of the files makes sense to others.
This patch causes the kernel to build dtbo files for:
arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs232-rts.dtbo
arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs422.dtbo
arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs485.dtbo
The intention is that these files are used by boot firmware (U-Boot)
to adjust the dtb before passing it to the kernel.
Best regards,
Tim
More information about the linux-arm-kernel
mailing list