[PATCH v5 6/6] PCI: imx6: Add the compliance tests mode support

[Richard Zhu]

Refer to the system board signal Quality of PCIe archiecture PHY test
specification. Signal quality tests(for example: jitters,  differential
eye opening and so on ) can be executed with devices in the
polling.compliance state.

To let the device support polling.compliance stat, the clocks and powers
shouldn't be turned off when the probe of device driver is failed.

Based on CLB(Compliance Load Board) Test Fixture and so on test
equipments, the PHY link would be down during the compliance tests.
Refer to this scenario, add the i.MX PCIe compliance tests mode enable
support, and keep the clocks and powers on, and finish the driver probe
without error return.

Use the "pci_imx6.compliance=1" in kernel command line to enable the
compliance tests mode.

Signed-off-by: Richard Zhu <hongxing.zhu at nxp.com>
---
 drivers/pci/controller/dwc/pci-imx6.c | 47 ++++++++++++++++++---------
 1 file changed, 31 insertions(+), 16 deletions(-)

diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index 61b25f5cbf5c..773b9e45806b 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -146,6 +146,10 @@ struct imx6_pcie {
 #define PHY_RX_OVRD_IN_LO_RX_DATA_EN		BIT(5)
 #define PHY_RX_OVRD_IN_LO_RX_PLL_EN		BIT(3)
 
+static bool imx6_pcie_cmp_mode;
+module_param_named(compliance, imx6_pcie_cmp_mode, bool, 0644);
+MODULE_PARM_DESC(compliance, "i.MX PCIe compliance test mode (1=compliance test mode enabled)");
+
 static int pcie_phy_poll_ack(struct imx6_pcie *imx6_pcie, bool exp_val)
 {
 	struct dw_pcie *pci = imx6_pcie->pci;
@@ -832,10 +836,12 @@ static int imx6_pcie_start_link(struct dw_pcie *pci)
 	 * started in Gen2 mode, there is a possibility the devices on the
 	 * bus will not be detected at all.  This happens with PCIe switches.
 	 */
-	tmp = dw_pcie_readl_dbi(pci, offset + PCI_EXP_LNKCAP);
-	tmp &= ~PCI_EXP_LNKCAP_SLS;
-	tmp |= PCI_EXP_LNKCAP_SLS_2_5GB;
-	dw_pcie_writel_dbi(pci, offset + PCI_EXP_LNKCAP, tmp);
+	if (!imx6_pcie_cmp_mode) {
+		tmp = dw_pcie_readl_dbi(pci, offset + PCI_EXP_LNKCAP);
+		tmp &= ~PCI_EXP_LNKCAP_SLS;
+		tmp |= PCI_EXP_LNKCAP_SLS_2_5GB;
+		dw_pcie_writel_dbi(pci, offset + PCI_EXP_LNKCAP, tmp);
+	}
 
 	/* Start LTSSM. */
 	imx6_pcie_ltssm_enable(dev);
@@ -924,18 +930,20 @@ static void imx6_pcie_host_exit(struct pcie_port *pp)
 	struct device *dev = pci->dev;
 	struct imx6_pcie *imx6_pcie = to_imx6_pcie(pci);
 
-	imx6_pcie_reset_phy(imx6_pcie);
-	imx6_pcie_clk_disable(imx6_pcie);
-	switch (imx6_pcie->drvdata->variant) {
-	case IMX8MM:
-		if (phy_power_off(imx6_pcie->phy))
-			dev_err(dev, "unable to power off phy\n");
-		break;
-	default:
-		break;
+	if (!imx6_pcie_cmp_mode) {
+		imx6_pcie_reset_phy(imx6_pcie);
+		imx6_pcie_clk_disable(imx6_pcie);
+		switch (imx6_pcie->drvdata->variant) {
+		case IMX8MM:
+			if (phy_power_off(imx6_pcie->phy))
+				dev_err(dev, "unable to power off phy\n");
+			break;
+		default:
+			break;
+		}
+		if (imx6_pcie->vpcie)
+			regulator_disable(imx6_pcie->vpcie);
 	}
-	if (imx6_pcie->vpcie)
-		regulator_disable(imx6_pcie->vpcie);
 }
 
 static const struct dw_pcie_host_ops imx6_pcie_host_ops = {
@@ -1250,8 +1258,15 @@ static int imx6_pcie_probe(struct platform_device *pdev)
 		return ret;
 
 	ret = dw_pcie_host_init(&pci->pp);
-	if (ret < 0)
+	if (ret < 0) {
+		if (imx6_pcie_cmp_mode) {
+			dev_info(dev, "Driver loaded with compliance test mode enabled.\n");
+			ret = 0;
+		} else {
+			dev_err(dev, "Unable to add pcie port.\n");
+		}
 		return ret;
+	}
 
 	if (pci_msi_enabled()) {
 		u8 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_MSI);
-- 
2.25.1